Sun Microsystems SUN FIRE X4640 Manuel utilisateur
1
This guide describes the minimum steps you must perform to power on and boot your server for the first time.
Detailed installation information can be found in the Sun Fire X4640 Server Installation Guide (821-0240). Service
and diagnostics information can be found in the Sun Fire X4640 Server Service Manual (821-0243) and Sun Fire
X4640 Server Diagnostics Guide (820-0472). These documents are available at the following web site:
http://docs.sun.com/app/docs/prod/sf.x4640#hic
To purchase a printed book, go to http://store.vervante.com and follow the links to the Sun
Microsystems store. Refer to the section “Documentation for This Product” at the end of this document for
a complete list of documentation for this system.
Contents
Safety and Compliance Information
Before performing an installation, refer to the following documents for safety information regarding the Sun Fire
X4640 Server:
■Important Safety Information for Sun Hardware Systems—Printed document included in the ship kit.
■Sun Fire X4640 Safety and Compliance Guide (821-0242)—Available online at the Sun documentation web site.
Figure Legend
1Server
2Documentation set, licensing agreement,
safety information, and other documents
3Network cables
4Four power cables (part of country kit; part number
varies depending on country.)
59-pin serial to 8-pin RJ-45 adapter
Sun Fire™X4640 Server
Getting Started Guide
2
Install Optional Components
Before installing the server into the rack, you must first install any optional components that you ordered with
the server, such as DIMMs, PCIe cards, and so on. Refer to the Service Manual for the instructions on installing
optional components.
Mount the System In a Rack
For rackmounting instructions, refer to the instructions included with the rail kit, the service label on the server,
and the online Installation Guide.
▼To Connect the Cables
1. Connect a serial cable between the server’s SER MGT port and a terminal device.
This connection provides your initial communication with the service processor (SP). The device must be
set up to communicate using the following settings:
■9600 baud
■8 bit
■no parity
■1 stop bit
A null modem configuration is needed, meaning the transmit and receive signals are reversed (crossed over)
for DTE-to-DTE communications. You can use the supplied RJ-45 crossover adapters with a standard RJ-45
cable to achieve the null modem configuration.
2. (Optional) Connect an Ethernet cable between the server’s NET MGT port and the network to which
future connections to the SP and host will be made.
After the initial configuration of the system using the SER MGT port, communication with the SP and host
is usually performed through this Ethernet interface.
3. Connect an Ethernet cable between one of the server’s NET ports (for example, NET 0) and the network
to which the server will communicate.
Figure Legend
1Power supply 0, 1, 2, and 3 (bottom to top)
2SER MGT port
3NET MGT port
4NET 0, NET 1, NET 2, and NET 3 ports
3
4. Connect the power cords to the power supplies and then to separate power sources.
There can be a maximum of 4 hot-swappable 1133W power supplies. The redundancy scenarios are:
■1 PSU = System will not power on
■2 PSUs = No redundancy
■3 PSUs = 2 + 1 redundancy
■4 PSUs = 2 + 2 redundancy
To provide redundancy, connect each power supply to a separate power source.
When power is applied, the SP initializes and the power supply LEDs illuminate. After a few minutes, the
SP login prompt appears on the terminal device. Note that the host is not initialized or powered on yet.
For more information on connecting cables, refer to the Installation Guide.
▼To Power On the System
Use this procedure to apply standby power to the service processor (SP) before initial configuration.
Caution – Do not operate the server without all fans, component heat sinks, air baffles, and the cover
installed. Severe damage to server components can occur if the server is operated without adequate
cooling mechanisms.
1. Verify that the power cords are connected and that standby power is on.
At this point, standby power is supplied only to the service processor and power supply fans. Do not apply
main power to the rest of the server until you are ready to install a platform operating system. In standby
power mode, the Power/OK LED on the front panel flashes.
2. Use a non-conducting pointed object to press and release the recessed Power button on the front panel.
When main power is applied to the full server, the Power/OK LED next to the Power button illuminates and
remains lit.
Figure Legend
1Locate LED/button
2Service-action-required LED
3Power/OK LED
4Power button
5Front fan fault LED
6Power supply fault LED
7System overheat fault LED
8Drive status indicator LED
9USB ports (2)
10 DVD-ROM drive (top of CD to left at insertion)
11 Disk drives (4)
4
Note – The first time the server powers on, the power-on self-test (POST) can take from one to several minutes
to complete.
3. Continue with initial software setup tasks, as described in the Installation Guide.
Connection Options
This section describes the tasks for initial setup of the service processor (SP) and Integrated Lights Out Manager
(ILOM) software. Refer to the Sun Integrated Lights Out Manager documentation for instructions on using
ILOM to configure and manage the server.
You can connect to the ILOM SP to perform initial setup and configuration in three ways:
■Using a Serial Connection (serial management port)
■Using an Ethernet Connection (DHCP)
■Using an Ethernet Connection (static IP address)
The method for connecting to ILOM using a serial connection is given in this document. For the remaining
methods, refer to the Installation Guide.
▼To Connect to ILOM Using a Serial Connection
1. Press Enter on the terminal device to create a connection between the terminal device and the ILOM SP.
2. Log in to ILOM.
The default user name is root; the default password is changeme.
3. Start the serial console:
-> cd /SP/console
-> start
Set Up the Platform Operating System, Driver Software, and Firmware
After configuring the ILOM SP with network settings, you can configure a preinstalled OS or install a
supported OS.
Note – Sun highly recommends using the Sun Installation Assistant (SIA) to update firmware (regardless of
OS) and to install a Linux or Windows OS. SIA is available in your Documentation and Media Kit and online at:
http://www.sun.com/systemmanagement/sia.jsp
5
Update Firmware
Sun highly recommends that you use the Sun Installation Assistant (SIA) to upgrade system BIOS and Sun
Integrated Lights Out Manager (ILOM) firmware. SIA is easy to use and available in the Documentation and
Media Kit, or online at:
http://www.sun.com/systemmanagement/sia.jsp
For more information, refer to the documentation for the version of SIA supported for your server at:
http://docs.sun.com/app/docs/prod/install.x64svr#hic
To upgrade system BIOS and ILOM firmware without using SIA, refer to Sun ILOM 3.0 Supplement for the
Sun Fire X4640 Servers at:
http://docs.sun.com/app/docs/prod/sf.x4640#hic
Hardware Warranty and Software Service Plan
For information on hardware warranty, see: http://www.sun.com/service/warranty/index.jsp
For information on a software service plan, see: http://www.sun.com/service/serviceplanssoftware/
You might be asked for your hardware serial number if you need service for your system. To find the serial
number of your system, use the ILOM command get /SYS or see your Installation Guide or Service Manual.
Documentation for This Product
The following table lists the documentation in the approximate order of the tasks that you might perform when
installing a new system. Review the tasks on the left, and then refer to the corresponding documentation on the
right. You can find the most up-to-date versions of all the documents at the Sun documentation web site:
http://docs.sun.com/app/docs/prod/sf.x4640#hic
OS
Read this
document: For information, go to:
For drivers and
firmware, go to: For patch information:
Preinstalled
Solaris OS
Installation
Guide (821-
0240)
http://www.sun.com/
software/preinstall/
http://store.vervante.com
http://
www.sun.com/
software/
solaris/10/
index.jsp
See the Sun Fire X4640
Server Product Notes (821-
0245)
http://
sunsolve.sun.com
Solaris OS See the
appropriate
OS Installation
Guide on
docs.sun.com
http://www.sun.com/
software/solaris/
OpenSolaris http://
www.opensolaris.org/os/
VMware
(ESX)
http://www.vmware.com/
http://www.sun.com/
servers/x64/x4640/os.jsp
http://
www.sun.com/
servers/x64/
x4640/
downloads.jsp
http://
www.vmware.com/
download/
Windows http://www.sun.com/
servers/x64/x4640/os.jsp
Use SIA for automatic driver and
firmware updates:
http://www.sun.com/
systemmanagement/sia.jsp
http://
update.microsoft.com/
Linux Red Hat: https://
www.redhat.com/apps/
download/
SUSE: http://
download.novell.com/
index.jsp
6
Part No. 821-0090-10, Rev. A
October 2009
Sun Microsystems, Inc.
www.sun.com
Sun Contact Information
Topic URL
Technical support http://www.sun.com/service/contacting
Submitting comments on this
document
http://www.sun.com/hwdocs/feedback
Please include the title and part number of your document with your feedback:
Sun Fire X4640 Server Getting Started Guide (821-0090-10)
Some of the documentation is available in French, Simplified Chinese, and Japanese; however, the English
documentation is the most up-to-date. For translated versions of the documentation, go to
http://docs.sun.com and select your language.
Task Document Part Number
Review safety information. Safety and Compliance Manual 821-0242
Important Safety Information for Sun Hardware Systems 816-7190
Review any known issues and workarounds. Sun Fire X4640 Server Product Notes 821-0245
Cable and power on the server. Connect to the
service processor and determine the network
settings. Configure the preinstalled Solaris OS.
Sun Fire X4640 Server Installation Guide 821-0240
Manage server accounts, monitor alerts, set
remote access and redirection, and view
component status and event logs.
Sun ILOM 3.0 Supplement for the X4640 Server 821-0241
Customize BIOS settings and RAID settings.
Remove and replace hardware components.
Troubleshoot and isolate server problems.
Sun Fire X4640 Server Service Manual
Also available at http://store.vervante.com
821-0243
Copyright 2009 Sun Microsystems, Inc. All rights reserved.
Copyright 2009 Sun Microsystems, Inc. Tous droits réservés.
Autres manuels pour SUN FIRE X4640
1
Table des matières
Autres manuels Sun Microsystems Serveur
Sun Microsystems
Sun Microsystems Fire 6800 Mode d’emploi
Sun Microsystems
Sun Microsystems Netra 150 Guide de démarrage rapide
Sun Microsystems
Sun Microsystems Sun Fire X4100 Manuel de service
Sun Microsystems
Sun Microsystems Sun Fire V480 Manuel
Sun Microsystems
Sun Microsystems Sun Fire T200 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire X4150 Server Manuel de service
Sun Microsystems
Sun Microsystems Sun Fire V445 Mode d’emploi
Sun Microsystems
Sun Microsystems Sun Fire X4150 Server Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Manuel utilisateur
Sun Microsystems
Sun Microsystems Ultra Enterprise 450 Manuel utilisateur
Sun Microsystems
Sun Microsystems Ultra 30 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire V100 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire X4150 Server Mode d’emploi
Sun Microsystems
Sun Microsystems Blade X6270 M2 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire V480 Manuel utilisateur
Sun Microsystems
Sun Microsystems SPARC T5120 Manuel utilisateur
Sun Microsystems
Sun Microsystems Netscape Enterprise Server Manuel de service
Sun Microsystems
Sun Microsystems Fire High-End Server Systems Manuel de programmation
Sun Microsystems
Sun Microsystems Netra T4 AC100 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Blade X6270 Manuel utilisateur
