Sun Microsystems Netra 440 Manuel utilisateur
Introduction
This guide presents an overview of the Netra™ 440 server
installation.
For complete installation instructions, refer to the
Netra 440 Server Installation Guide.
Documentation
You can view, print, or download manuals from the
Sun™ documentation web site:
http://www.sun.com/documentation
■Netra 440 Server Release Notes
(817-3885-xx)
Latest product updates
■Netra 440 Server Product Overview
(817-3881-xx)
Product overview information
■Netra 440 Server Installation Guide
(817-3882-xx)
Detailed rackmounting, cabling, power-on, and
configuring information
■Netra 440 Server Service Manual
(817-3883-xx)
Service information
■Netra 440 Server System Administration Guide
(817-3884-xx)
Administration information
■Netra 440 Server Diagnostics and Troubleshooting Guide
(817-3886-xx)
Diagnostics and troubleshooting information
■Sun Advanced Lights Out Manager User’s Guide for the
Netra 440 Server (817-5481-xx)
Advanced Lights Out Manager (ALOM) software
information
■Netra 440 Server Safety and Compliance Manual
(817-6225-xx)
Essential safety and compliance information
Shipment Contents
Besides the server (shown on the left), the ship kit contains:
Note – The DC connectors are for the DC-powered servers
only. Use the separately ordered AC cables with the
AC-powered server.
Antistatic
wrist strap
RJ-45 serial
console cable
M5 nut kit
RJ-45 to
DB-9 adapter
RJ-45 to DB-25
adapter
Rackmount kit
DC connectors
(For DC servers only)
Netra™440 Server Quick Start Guide
The shipment also contains these documents:
Important Safety Information for Sun Hardware (816-7190-xx),
Sun Netra 440 Server Product Documentation (817-4755-xx),
Binary Code Licenses (816-4835-xx), Sun Install Check Tool
(817-0440-xx), and this guide.
1. Viewing Front Components
1. Press in on the door release latches to lower the front
door.
2. View the components accessible from the front panel.
2. Mount Server to Rack
Detailed instructions on mounting the server in a rack are
in the Netra 440 Server Installation Guide. The following rack
mount kits are available for the Netra 440 server.
■19-inch 4-post sliding or hardmount
■19-inch 2-post hardmount
■23-inch 2-post hardmount
■600 mm 4-post hardmount
Door release latches
SCC
System configuration
card reader Rotary switch
On/Standby
button
Hard drives
Fan trays 0-2
Power distribution
DVD drive board
Following are the basic instructions for the 19-inch 4-post
hardmount rack mount kit:
1. Get the front hardmount brackets from the rack kit
and secure the front brackets to the sides of the server.
2. Get the two rear mount support brackets from the
rack kit and install the rear mount support brackets at
the rear of the server.
3. Lift the server to the desired location in the rack.
4. Secure the front hardmount brackets attached to the
sides of the server to the front of the rack.
5. Get the two rear mount flanges from the rack kit and,
at the rear of the rack, use the two captive screws to
secure the two rear mount flanges to the rear mount
support brackets that are attached to the server.
6. Using two screws for each rear mount support
bracket, secure the rear mount support brackets to the
rear of the rack.
3. Attach Cables
Alarm
DB-15 connector; use this port to connect to the central
office alarming system.
Serial
DB-9 connector; use this port (TTYB) for general purpose
serial data transfer.
USB
Use the ports (USB0–3) to connect to external USB devices.
Captive screws to
secure flange to
rear of server
Screws to secure
flange to rack
AlarmSerial USB Ethernet SCSI Net MGT
Serial MGT
AC power OR DC power Ground
studs
You cannot mix AC and DC power supplies in the same server
Ethernet
RJ-45 connectors; use these ports (NET0, NET1) to connect
to autonegotiating 10/100/1000BASE-T Ethernet networks.
SCSI
Ultra320 LVD SCSI connector; use this port to connect to
external SCSI devices.
SERIAL MGT
RJ-45 connector; use this serial port for server management
using the ALOM software. If needed, use the supplied
RJ-45 to DB-9 or RJ-45 to DB-25 adapters.
NET MGT
RJ-45 connector; use this port for making an Ethernet
connection to the ALOM software.
AC Power (AC Server Only)
Connect the AC power cords to the AC power source.
DC Power (DC Server Only)
Assemble DC connectors and connect to DC power source.
Ground Studs (DC Server Only)
Connect to protected earth ground.
Note – Refer to the Netra 440 Server Installation Guide for
complete cabling instructions.
4. Power On Server
Note – The server goes into Standby mode as soon as the
power cables are connected to the power source.
1. Make sure the rotary switch is in the Normal (|)
position before powering on the server.
SCC
Forced Normal Locked
Diagnostics
standby
Part No. 817-4756-11, Rev. A
August 2004
Sun Microsystems, Inc.
www.sun.com
2. Set up a console connection to the server using the
server’s SERIAL MGT port.
Refer to the Netra 440 Server Installation Manual for
complete instructions.
3. Power on server either from the keyboard or by
pressing the system power button at the front of the
server.
Note – Refer to the Netra 440 Server Installation Manual for
complete power on and configuration instructions.
Indicator Overview
Front Panel Indicators
SCC
System status Hard drives Fan trays 0-2
Alarms
Rear Panel Indicators
Note – Refer to the Netra 440 Server Installation Manual for
the description of these indicators.
System status NET MGT
Ethernet connection
Power supply
Copyright 2004 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers. Portions
may be derived from Berkeley BSD systems, licensed from U. of CA. Sun, Sun Microsystems, the Sun logo, Netra, and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in
the U.S. and in other countries. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and in other countries.
U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and applicable provisions of the FAR and its supplements.
Copyright 2004 Sun Microsystems, Inc. Tous droits réservés. Distribué par des licences qui en restreignent l’utilisation. Le logiciel détenu par des tiers, et qui comprend la technologie relative aux
polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun. Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de
Californie. Sun, Sun Microsystems, le logo Sun, Netra, et Solaris sont des marques de fabrique ou des marques déposées de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes
les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans d’autres pays.
Autres manuels pour Netra 440
5
Table des matières
Autres manuels Sun Microsystems Serveur
Sun Microsystems
Sun Microsystems Netra 440 Manuel utilisateur
Sun Microsystems
Sun Microsystems Netra X1 Manuel utilisateur
Sun Microsystems
Sun Microsystems Enterprise 250 Manuel de service
Sun Microsystems
Sun Microsystems Netra ct Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire V480 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire V100 Manuel utilisateur
Sun Microsystems
Sun Microsystems Netra t 1125 Manuel utilisateur
Sun Microsystems
Sun Microsystems Enterprise 6 00 Series Manuel utilisateur
Sun Microsystems
Sun Microsystems Blade X6275M2-BB Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire V215 Mode d’emploi
Sun Microsystems
Sun Microsystems Fire 4810 Manuel d'instructions d'installation
Sun Microsystems
Sun Microsystems Blade X6450 Manuel utilisateur
Sun Microsystems
Sun Microsystems Netra 240 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire V880 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Fire X2250 Manuel utilisateur
Sun Microsystems
Sun Microsystems Enterprise 3500 Manuel utilisateur
Sun Microsystems
Sun Microsystems Sun Enterprise 10000 Manuel technique
Sun Microsystems
Sun Microsystems Sun Fire E25K Manuel utilisateur
Sun Microsystems
Sun Microsystems SUN FIRE X4640 Manuel utilisateur
Sun Microsystems
Sun Microsystems Netra ct Manuel utilisateur
