Sun Cupid Riptide Manuel utilisateur
Riptide
User Manual
CONTENTS
Getting Started ……………………………………………………………………… 3
Waterproof & Dustproof Performance …………………………………….. 9
Specifications ……………………………………………………………………… 10
Troubleshooting
……………………………………………………………………… 11
Contact Support
……………………………………………………………………… 13
Warnings
……………………………………………………………………… 13
FCC Statements
……………………………………………………………………… 16
Warranty Information
…………………………………………………………… 17
2
GETTING STARTED
(g)
(h)
(i)
(j)
(e)
(b)
(f)
(a)
(d)
( c)
(k)
IN THE BOX
- NUU Riptide
- MicorUSB Cable
- 3.5mm to 3.5mm audio cable
- User Manual
- Carabiner (optional)
3
(a). Bluetooth Status LED
This is a small LED that illuminates to show the current status of the Riptide’s Bluetooth connection.
•
•
Flashing Quickly and Steadily: Pairing mode.
•
Solidly Lit: Paired and connected.
(b). On/Off Button
NOTE: The Bluetooth Status LED will light when the Riptide is on, and go dark when it is off .
Flashing Slowly and Intermittently: The Riptide is on and is not in pairing mode. This is also the indicator for “auto-reconnect”, where the
Riptide attempts to connect with the last paired Bluetooth device immediately after it is powered on. Riptide will enter pairing mode when it
cannot find the previous paired Bluetooth device.
Off: Press and hold the button for ~3 seconds to turn the NUU Riptide off. You will hear a two-tone (high-low) sound, indicating that the speaker has
been switched off.
On: Press and hold the button for ~3 seconds to turn the NUU Riptide on. You will hear a two-tone (low-high) sound, indicating that the speaker is
on.
Auto-off: After 30 minutes of inactivity, the NUU Riptide will shut off automatically. To turn the Riptide on again, Press and hold the button for ~3
seconds. The NUU Riptide will not automatically shut off if you are playing audio through Bluetooth, or 3.5mm connection.
4
( c). Action Button
The Action button has the Play/Pause symbol embossed into it as well as a Phone icon silkscreened above it This button controls:
- Pairing of Bluetooth device
- Play/Pause
- Answer/Reject Phone Call
TO PAIR THE Riptide WITH YOUR BLUETOOTH DEVICE:
1. Switch on the NUU Riptide. The Bluetooth Status LED will flash slowly.
3. Enable Bluetooth on your phone or other device.* Then select “NUU Riptide” from the list of discoverable devices.
4. If prompted for a PIN code, enter “0000” (4 zeros).
5. It will take between 10-15 seconds for the NUU Riptide to pair with your device. When pairing is successful, you will hear a two-tone (low-high)
sound and the Bluetooth Status LED will remain steadily lit.
2. Press and hold the Action Button for about ~3 seconds. You will hear a double-beep (low-low) and the Bluetooth Status Light will flash quickly. The
NUU Riptide is now in pairing mode.
NOTE: Procedures for activating Bluetooth will vary across devices. Consult the documentation that came with your phone or other device for further
information.
5
PLAYBACK:
ANSWER / REJECT PHONE CALL:
During a phone call, press and hold the Action button for 1-2 seconds to switch between using the NUU Riptide and your phone to talk. You will hear a
'beep' indicating that the call has been transferred to your phone or the NUU Riptide.
The Action Button doubles as a “Play/Pause” button. While music is playing, press and release the Action Button to pause the music. Press and
release the button again to resume playback.
The NUU Riptide may be used as a wireless speakerphone. Use your phone to dial as usual, and speak toward the built-in microphone located below
the power on/off button of the unit. The built-in microphone only works when your phone/device is connected via Bluetooth.
To answer or end an incoming call, press and release the Action button. Incoming and outgoing calls are given priority over Bluetooth audio playback.
If a call comes in while you are streaming Bluetooth audio, the track will pause and the Riptide will play the ring tone. It will resume once the call is
ended.
To reject an incoming call, press and hold the Action Button for one second. You will hear a two-tone sound and the call will go to voicemail.
6
(d) Volume up (e) Volume down
CONTROLLING VOLUME
(f) Charging Indicator
Press or hold the volume keys to adjust the volume. The NUU Riptide will beep with each change in volume. When you reach maximum volume, you
will hear a high-pitched beep. When you reach minimum volume, you will hear a faint low-pitched beep.
NOTE: Volume may only be adjusted while the NUU Riptide is connected to a Bluetooth device. While the Riptide is connected via the AUX-IN, the
volume is set to maximum. You must then adjust playback volume via the volume controls on your phone/device.
An occasional flashing red light indicates that the battery is low and should be recharged soon. When charging, this light shows green until the NUU
Riptide is fully charged.
7
(g) Micro-USB port
CHARGING THE Riptide'S BATTERY
USB SPEAKER
(h) AUX IN (i) AUX OUT
The NUU Riptide can connect to any device with a 3.5mm headphone jack. Use the supplied 3.5mm cable to plug in the AUX IN port of Riptide and
the other end to the 3.5mm headphone jack of your phone/device. Like any phone's headphone jack, the AUX OUT of Riptide can be used as music
source that you can connect to another Riptide's AUX IN to double the sound output power.
Connect the supplied Micro-USB cable into the charging port, and plug USB side into your computer or USB AC adapter (adapter not supplied). The
green charging indicator will remain illuminated while the unit is charging. The indicator will automatically switch off when the unit is fully charged. Allow
around 2.5 hours for the battery to fully charge.
NUU Riptide can be used as USB speaker when connected to your computer USB port. No driver is required. Ensure Riptide is fully charged before
use as your computer USB port may not be able to supply enough power to charge and play music at the same time.
8
(j) Carabiner Loop
An attached ring on the I/O port side for hooking a carabiner.
(k). Tripod Mount
For mounting to a tripod.
WATERPROOF & DUSTPROOF PERFORMANCE
The NUU Riptide is designed to be waterproof and dustproof. Damage caused from misuse, abuse or failure to properly maintain the Riptide is not
covered by the limited warranty.
• The Riptide is IP57 certified and will operate at a water depth of 3 feet for up to 30 minutes.
• Use the Riptide in the recommended operating water temperature range of –10°C to +40°C (14°F to 104°F). Do not use in hot springs.
• As for dustproof performance, there is no guarantee that the Riptide will not become scratched or dented.
• Accessories supplied do not meet waterproof and dustproof specification cations.
9
NOTES BEFORE USING Riptide UNDER/NEAR WATER
Specifications -
Design and specifications are subjected to change without notice.
- IP57 waterproof & dustproof rating
- 1 x Passive bass radiator
- Bluetooth Version: 4.0
- Pairs with any Bluetooth 2.0 device
- 1 x 50mm 4 ohm speaker driver
- 10m Bluetooth Range
- 3.5mm AUX-IN & AUX OUT
- up to 6 hours of playback time (80% volume)
- Dimensions (WxHxD): 68 x 69 x 68mm
- 1 x 3W audio output power
- A2DP profile
- Weight : 165g
• Always confirm that the cover over the charging, AUX-IN & AUX-OUT ports has been securely sealed. Riptide will only meet IP57 standards when
cover has been securely closed. To securely close the cover, follow these steps:
1. Firmly seat the inside edge of the cover in place
2. Using both thumbs, press down at both ends of the cover at the same time to ensure it is in place, flush, and sealed
• If dirt or sand gets on the power charging port, wipe the area clean with a soft cloth that will not leave behind and fibers.
• Do not open or close the charging port cover with wet or sandy hands or near water.
• Make sure the Riptide is completely dry before opening the charging port cover.
10
Table des matières
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur