Sumec 5554-511 Manuel utilisateur

After-sales Service Guide

12" snow shovel

SAN: 0533200803ZG

Customer Model: 5554-511

CONTENTS

Specification 3

Main parts Location 3

BOM& Spare Parts List 4

Operating Instructions 4

Maintenance and Storage 10

FAQS 11

Specification

Main parts Location

CARTON CONTENTS

•Electric snow shovel

•Joint -fixing knob and bolt

•Adjustable handle and knob

•Manual

BOM& Spare Parts List

See Appendix 1.

Operating Instructions

ASSEMBLY

CONNECTING THE UPPER AND LOWER TUBES

1. Fit the upper and lower tubes together and tighten the joint-fixing knob

(Fig.1).

2. Assemble the adjustable handle and tighten the handle knob (Fig. 2 and 3).

NOTE: the tip on the lower clip shall be inserted to the slot on the upper tube.

OPERATION

CONNECTING TO A POWER SUPPLY

To reduce the risk of electric shock, this appliance has a polarized plug (i.e.

one blade is wider than the other; see Fig. 4).

Use this appliance only with a polarized UL-, CSA- or ETL- listed extension

cord recommended for outdoor, all-weather use.

The appliance plug will fit into a polarized extension cord only one way. If the

appliance plug does not fit fully into the extension cord, reverse the plug. If the

plug still does not fit, obtain a correct polarized extension cord. A polarized

extension cord will require the use of a polarized wall outlet. The extension

cord plug will fit into the polarized wall outlet only one way. If the plug does not

fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact

a qualified electrician to install the proper wall outlet. Do not modify the

appliance plug, extension cord receptacle or extension cord plug in any way.

IMPORTANT: Check the extension cord frequently during use for holes or

cracks in the insulation. Do not use a damaged cord. Do not run the cord

through standing water or wet grass.

Use only an extension cord recommended for outdoor use.

SECURING THE EXTENSION CORD

Make a loop with the extension cord (Fig. 5).

Insert the loop through the opening in the back of the upper handle and secure

the loop onto the extension cord hook (Fig. 6).

Connect the extension cord to the snow shovel.

NOTE: Securing the extension cord in this way helps to prevent you from

acciden-tally disconnecting the extension cord from the snow shovel during

operation.

Plug the extension cord into a wall outlet.

Keep the area to be cleared free of stones, toys or other foreign objects that

the rotating paddles might pick up and throw. Such items could be covered by

snow and are easy to overlook, so be sure to conduct a thorough inspection of

the area before operating the snow shovel.

STARTING AND TOPPING

To start the electric snow shovel, push and hold the safety lock button on the

top of the handle grip with your thumb and then squeeze the trigger switch with

your fingers. Once the machine powers on, you can release the safety lock

button and proceed with operation (Fig. 7).

To stop the electric snow shovel, release the trigger switch (Fig. 7).

OPERATING TIPS

Start the electric snow shovel and tilt it forward until the scraper blade at the

base of the unit contacts the ground. Push the shovel forward at a comfortable

rat e, yet slow enough to clear the path completely. The clearing width of the

snow shovel and the depth of snowfall should dictate your forward speed.

Direct the snow discharge to the right or to the left by holding the electric snow

shovel at a slight angle. To remove snow most efficiently, throw the snow

down- wind and slightly overlap each swath.

If you need to clear snow from a crushed rock or gravel surface, push down on

the handle to clear the scraper of any loose material that the rotating paddles

could throw.

This electric snow shovel cuts a path 12" /30.5 cm wide and up to 6"/15.24 cm

deep in one pass.

When clearing deeper drifts, hold the electric snow shovel by the upper and

lower handles and use a swinging or sweeping motion. Remove up to 6" /15.24

cm of snow with each pass and repeat as many times as needed.

Keep the cord clear of obstructions, sharp objects and the rotating paddles. Do

not pull sharply on the cord or abuse it in any manner. Frequently inspect the

cord for signs of damage. If damage is found, replace the cord immediately.

This electric snow shovel is equipped with a 1 W LED light to facilitate clearing

at night and under conditions of poor visibility (Fig. 8). When you start the

machine, the LED light will automatically power on and illuminate the path in

front of you. When you stop the machine, the LED light will automati-cally

power off.

Disconnect the extension cord after using the electric snow shovel. Hang the

extension cord with the shovel so it will not be misplaced or damaged.

REPLACING THE PADDLE

Use a wrench to remove the bolt and the washer on the right side of the

housing (Fig. 9).

Using a cross-head screwdriver, disassemble the left side cover by removing

the seven screws (Fig. 10).

Remove the tensioner. Unscrew the three screws securing the big pulley plat e,

then remove the plate and pulley assembly (Fig. 11).

Remove the old paddle from the housing (Fig. 12).

To install the new paddle, place the washer (A) back onto the bolt (removed in

step 1) and insert the bolt so that it protrudes slightly into the housing of the

unit. Thread the nut and then the other washer (B) onto the bolt. Fit the new

paddles onto the end of bolt and tighten the bolt (Fig. 13).

Reinstall the big pulley plate and align it with the other end of the paddles. After

fitting the paddles into position, secure the big pulley plate with the three (3)

screws (Fig. 14).

NOTE: The housing will flex to allow for installation of the new paddl e.

Place the tensioner back into position. Rotate the paddles to ensure that the

belt and paddles move freely, then reinstall the cover by securing it with the

seven screws (Figs. 15 & 16).

WARNING! Do not power the unit until the cover guard is securely in place to

prevent damage or injury.

REPLACING THE BELT

Disassemble the left side cover by removing the seven screws (Fig. 10).

Remove the tensioner (Fig. 17).

Unscrew the three (3) screws from the big pulley plate and the four (4) screws

from the small pulley plate (Fig.17).

Replace the worn belt with a new belt.

Screw the big and small pulley plates back into position, then reinstall the

tensioner.

Place the left side cover back into position and refasten the seven screws.

REPLACING THE SCRAPER BLADE

Position the paddles so that you can gain access to the three screws that

secure the scraper blade to the base of the unit.

Using a long cross-head screwdriver, remove the three screws and the old

scraper blade (Fig. 18).

Install the new scraper blade and fasten it securely to the snow shovel with the

three screws.

LUBRICATING THE ELECTRIC SNOW SHOVEL

This electric snow shovel does NOT need lubrication. All bearings are

lubricated at the factory for the life of the product.

Maintenance and Storage

•Check all fasteners at frequent intervals for proper tightness to ensure that

the equipment is in safe working condition.

•Always refer to the operator's manual for important details, such as how to

properly store your electric snow shovel for an extended period of time.

•Maintain or replace safety and instruction labels as needed.

•Run the machine a few minutes after throwing snow to prevent the paddle

from freezing.

DOUBLE INSULATED: GROUNDING NOT REQUIRED.

WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS.

This snow shovel is double insulated, eliminating the need for a separate

grounding system. Use only identical replacement parts. Read the instructions

before servic-ing double insulated appliances. Use this snow shovel only as

described in this manual.

STORAGE

Examine the electric snow shovel thoroughly for worn, loosed or damaged

parts.

Should you need to repair or replace a part.

Examine the extension cord thoroughly for signs of excess wear or damage. If

it is worn or damaged, replace it immediately.

Disconnect the extension cord from the electric snow shovel before storing.

Store the cord with the electric snow shovel indoors in a clean, dry and locked

location out of the reach of children and animals.

NOTE: Devices for storing extension cords are commercially available, should

you wish to purchase one.

Table des matières

Autres manuels Sumec Souffleuse à neige

Sumec

Sumec 5554-747 Manuel utilisateur

Manuels Souffleuse à neige populaires d'autres marques

Murray

Murray 624504X4A Manuel utilisateur

Blizzard

Blizzard POWER PLOW 8100PP Manuel utilisateur

Craftsman

Craftsman 486.24837 Manuel utilisateur

Yard-Man

Yard-Man E2B5 Manuel utilisateur

ST ST 526 A Manuel utilisateur

MTD

MTD 3AA Manuel utilisateur

Toro

Toro Power TRX 1428 OHXE Manuel utilisateur

Ryobi

Ryobi RYAC800 Manuel utilisateur

Poulan Pro

Poulan Pro 416829 Manuel utilisateur

Poulan Pro

Poulan Pro 437986 Manuel utilisateur

MTD

MTD 319-180-00 Manuel utilisateur

Brute

Brute 1695565 Manuel utilisateur

Egholm

Egholm City Ranger 2250 Manuel utilisateur

Poulan Pro

Poulan Pro 420915 Manuel utilisateur

GreenWorks

GreenWorks SNF402 Manuel utilisateur

LOFTNESS

LOFTNESS 601D1 Manuel utilisateur

LOFTNESS

LOFTNESS 1082I Manuel utilisateur

LOFTNESS

LOFTNESS 481EL Manuel utilisateur