StyleCrest VEXAR CD36M-B Guide de démarrage rapide

For more information, visit www.fmiproducts.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

DIRECT VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

MODELS WITH FAN

CD36M-B, CD42M AND CD42M-A

MODELS WITH FAN AND DOOR SWITCH

CD36M-B2, CD42M-A2

PFS

www.fmiproducts.com 119212-01E2

WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause injury or

property damage. Refer to this manual for correct in-

stallation and operational procedures. For assistance

or additional information consult a qualied installer,

service agency or the gas supplier.

WARNING: This direct vent gas replace is intended

for use with natural or propane/LP gas only. Do not at-

tempt to burn any solid fuels in this appliance.

This replace is manufactured for Stylecrest Inc. under

the Vexar brand name by FMI PRODUCTS, LLC.

This replace may be installed as an OEM installation

in a manufactured (mobile) home and must be installed

in accordance with the manufacturers instructions and

the Manufactured Home Construction and Safety Stan-

dard, Title 24 CFR, Part 3280 in the United States. This

replace is only for use with the type(s) of gas indicated

on the rating plate. A conversion kit is supplied with the

replace.

State of Massachusetts: The installation must be made

by a licensed plumber or gas tter in the Commonwealth

of Massachusetts.

SAVE THIS BOOK

This book is valuable. In addition to instructing you on how to install and

maintain your appliance, it also contains information that will enable you to

obtain replacement parts or optional accessory items when needed. Keep

it with your other important papers.

TABLE OF CONTENTS

Introduction.......................................................... 3

Selecting Location ............................................... 3

Safety .................................................................. 4

Local Codes......................................................... 6

Product Features................................................. 6

Pre-Installation Preparation.................................. 6

Requirements for the Commonwealth of

Massachusetts..................................................... 9

Installation ......................................................... 10

Burner Flame Adjustment.................................. 25

Operation........................................................... 26

Gas Conversion................................................. 27

Troubleshooting................................................. 29

Specications .................................................... 30

Replacement Parts............................................ 30

Service Hints ..................................................... 30

Technical Service............................................... 30

Accessories ....................................................... 31

Parts .................................................................. 32

Limited Two Year Warranty..................Back Cover

www.fmiproducts.com

119212-01E 3

INTRODUCTION

WARNING: This product con-

tains and/or generates chemicals

known to the State of California

to cause cancer or birth defects

or other reproductive harm.

Models CD36M-B series and CD42M-A

series are heat circulating gravity direct vent

replaces with sealed combustion chamber.

These replaces use millivolt gas control valve

and millivolt ignition system.

These fireplaces are convertible with the

standard setup as natural gas. Conversion

may be performed by the OEM mobile home

builder or by a qualied service person on-

site. If you are uncertain as to what gas your

unit is equipped for, please check the rating

plate located inside of the appliance opening

or consult your mobile home supplier or your

local distributor of Style Crest, Inc. products.

NOTICE: Check local building

codes for area requirements

before installing this appliance.

BEFORE YOU BEGIN

Before beginning the installation of your

appliance, read these instructions through

completely.

Figure 1 - Common Fireplace Locations

FULL

PROJECTION CORNER

INSTALLATION

FLUSH

INSTALLATION

To determine the safest and most efcient

location for your replace, consider the fol-

lowing guidelines:

1. The location must allow for proper clear-

ances (see Figure 1).

• Flush installation is recommended where

living space is limited.

• Projected installation may be ideal for a

new addition to an existing nished wall.

• Corner installation makes use of a space

that may not normally be used and pro-

vides a wider and more efcient range

for radiant heat transfer.

2. Consider a location where the replace

would not be affected by drafts, air con-

ditioning ducts, windows or doors.

3. A location that avoids the cutting of joists

or roof rafters makes ventilation installa-

tion easier.

In selecting a location, the following precau-

tions must be observed:

• Do not connect this appliance to a chimney

system used for solid fuel burning replace.

• Due to high temperatures, do not locate

This Style Crest, Inc.replace and its com-

ponents are safe when installed according

to this installation manual and operated as

recommended. Unless you use Style Crest,

Inc.components designed and tested for

this replace system, YOU MAY CAUSE A

SAFETY HAZARD!

The Style Crest, Inc.warranty will be voided

by, and Style Crest, Inc.disclaims any respon-

sibility for the following actions:

A) Modication to the replace, components,

doors, blower, fans or vent system.

B)Use of any component part not manu-

factured or approved by Style Crest, Inc.

in combination with a Style Crest, Inc.

replace system.

Proper installation is the most important step

in ensuring safe and continuous operation of

the replace. Consult the local building codes

as to the particular requirements concerned

with the installation of all factory built re-

places. This replace, when installed, must be

electrically grounded in accordance with local

codes or in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70.

The installation must conform with local codes

or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1. This

appliance complies with ANSI Z21.88.

SELECTING LOCATION

this appliance in high trafc areas or near

furniture and draperies.

• Never obstruct openings of the appliance or

ow of ventilation air. Keep control compart-

ments accessible.

• Do not locate appliance close to where

gasoline or other ammable liquids may be

stored. The appliance must be kept clear

and free from combustible materials.

www.fmiproducts.com 119212-01E4

SELECTING LOCATION

Continued

• Do not use this appliance if any part has

been under water. Immediately contact a

local service technician to examine the

SAFETY

DANGER: Carbon monoxide poisoning may lead to death!

This replace must be installed by the O.E.M. builder or by a qualied (certied or licensed)

service person. It has a sealed gas combustion chamber that uses a coaxial pipe (pipe within a

pipe and having the same center) venting system. It brings in fresh air for combustion through

the outer pipe and combustion gases are exhausted through the inner pipe. If the glass door

assembly and venting pipe are not properly seated, connected and sealed, carbon monoxide

leakage (spillage) can occur.

Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning resemble the u,

with headaches, dizziness or nausea. If you have these signs, the replace may not be work-

ing properly. Get fresh air at once! Have replace serviced. Some people are more affected

by carbon monoxide than others. These include pregnant women, people with heart or lung

disease or anemia, those under the inuence of alcohol and those at high altitudes.

Propane/LP & Natural Gas:Propane/LP and natural gas are odorless. An odor-making agent

is added to the gas. The odor helps you detect a gas leak. However, the odor added to the

gas can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual for reference. It is your

guide to safe and proper operation of this replace.

WARNING: Any change to this replace or it’s controls can be

dangerous. Do not modify this replace under any circumstances.

Any parts removed for servicing must be replaced prior to operat-

ing replace.

WARNING: Do not use a blower insert, heat exchanger insert or

other accessory not approved for use with this replace.

WARNING: This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not convertible for

use with other gases unless a certied kit is used.

WARNING: Do not allow fans to blow directly into the replace.

Avoid any drafts that alter burner ame patterns.

Due to high temperatures, the appliance should be located out of

trafc and away from furniture and draperies.

Do not place clothing or other ammable material on or near the

appliance. Never place any objects on the appliance.

Do not use this replace to cook food or burn paper or other am-

mable material.

appliance and to replace any part(s) of the

control ignition system and other related

components that have been submerged

under water.

www.fmiproducts.com

119212-01E 5

This replace reaches high temperatures. Keep children and adults

away from hot surface to avoid burns or clothing ignition. Fireplace

will remain hot for a time after shutdown. Allow surface to cool

before touching.

SAFETY

Continued

Carefully supervise young children when they are in the room with

replace.

Keep the area around your replace clear of combustible materials,

gasoline and other ammable vapor or liquids. Do not run replace

where these are used or stored.

1. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lbs. capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not

use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier's instructions

• if you cannot reach you gas supplier, call

the re department.

3. Never install the replace

• in windy or drafty areas where curtains

or other combustible (ammable) objects

can make contact with the replace front

• in high trafc areas

4. Turn replace off and let cool before servic-

ing, installing or repairing. Only a qualied

service person should install, service or re-

pair this replace. Have replace inspected

annually by a qualied service person.

5. You must keep control compartments,

burners and circulating air passages clean.

More frequent cleaning may be needed due

to excessive lint and dust from carpeting,

bedding material, etc. Turn off the gas valve

and pilot light before cleaning replace.

6. Have venting system inspected annually

by a qualied service person. If needed,

have venting system cleaned or repaired.

7. Do not use any solid fuels (wood, coal, paper,

cardboard, etc.) in this replace. Use only the

gas type indicated on replace nameplate.

8. This appliance, when installed, must be

electrically grounded in accordance with local

codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70.

9. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

10. Do not operate replace if any log is

broken.

11. Do not operate replace with glass door

removed, cracked or broken.

12. Provide adequate clearances around air

openings.

www.fmiproducts.com 119212-01E6

PRODUCT FEATURES

These are a few facts that can help you un-

derstand and enjoy your direct-vent replace:

• The venting system may be routed to the

outside of your home in several ways. It

may vent through the roof (vertical) or it

may vent to an outside/exterior wall (hori-

zontal). The vent pipe installation is very

important to allow for proper operation.

You must follow the venting instructions

very carefully for either vertical or horizontal

applications.

• This replace may be installed in any room

of your house provided all local codes and

these installation instructions are followed.

• A piezo ignitor and ceramic electrode cre-

ate spark to ignite the pilot light. It does not

require any matches, batteries or any other

sources of ignition to light the pilot.

• Each time you turn on your replace, you

may notice some amount of condensation

on the inside of the replace glass. This

is normal and will disappear after 10-20

minutes of operation.

• Your direct-vent gas fireplace system

(replace and venting) is a balanced and

sealed gas operating unit. It requires ap-

proximately 10-20 minutes of operating

time before the ame pattern stabilizes.

• This replace is equipped with a millivolt

gas control system that does not require

electricity to operate. A piezo ignitor is

provided to light the pilot without using

matches or lighters.

• This model can accept an optional circulat-

ing air blower when 120 VAC connection is

supplied. If you plan to install an optional

blower, do not forget to wire the replace

outlet when framing.

PRE-INSTALLATION

PREPARATION

Figure 2 - Mantel Clearances

Top of Louver Opening

Wall

Mantel Depth Mantel From Top of Opening

(1) 14" (A) 16"

(2) 12" (B) 14"

(3) 10" (C) 12"

(4) 8" (D) 10"

(5) 6" (E) 8"

(6) 4" (F) 6"

(7) 2" (G) 4"

CAUTION: Do not block

required air spaces with insula-

tion or any other material. Do not

obstruct the effective opening

of the appliance with any type

of facing material.

CLEARANCES TO COMBUSTIBLES

Minimum clearances to combustibles for the

replace are:

• Back and Sides of Fireplace ........ 0"

• Floor .......................... 0"

• Perpendicular Wall ............... 6"

• Front ......................... 36"

• Top of Standoffs.................. 0"

MANTEL CLEARANCES

Woodwork, such as wood trims, mantles

and other combustible materials should be

placed within the required clearance speci-

ed in Figure 2.

LOCAL CODES

Install and use replace with care. Follow all

local codes. In the absence to local codes,

use the current National Fuel Gas Code ANSI

Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

www.fmiproducts.com

119212-01E 7

VENT TERMINATION CLEARANCES

Final position of your replace depends on

location of the vent termination in relation to

clearances that must be observed as shown

in Figure 5 on page 8.

The vent system serves as the “chimney” as

well as combustion air supply (air intake). The

horizontal run must have a rise of 1/4" (0.6 cm)

for every 12" (30.48 cm) of horizontal run to-

wards the termination. Maximum horizontal run

depends on vertical rise from replace adapter

collar to vent termination (see table below).

VERTICAL HORIZONTAL

0 to 1 ft (30.48 cm)

1 ft (30.48 cm) to 4 ft (121.92 cm)

2 ft (60.96 cm) to 8 ft (243.84 cm)

3 ft (91.44 cm) to 12 ft (365.76 cm)

4 ft (121.92 cm) to 16 ft (487.68 cm)

5 ft (152.40 cm) to 15 ft (457.20 cm)

6 ft (182.88 cm) to 14 ft (426.72 cm)

7 ft (213.36 cm) to 13 ft (396.24 cm)

8 ft (243.84 cm) to 12 ft (365.76 cm)

WARNING: Never allow the

vent to run downward as this

may cause excessive tempera-

tures which could cause a re.

WARNING: Horizontal sec-

tions of this vent system require

a minimum clearance of 2" from

the top of the pipe and 1" mini-

mum to the sides and bottom.

Vertical sections of this system

require a minimum of 1" clear-

ance to combustible materials

on all sides of the pipe.

PRE-INSTALLATION PREPARATION

Continued

Figure 3 - Framing Dimension

Figure 4 - Corner Installation

CD36M-B CD42M-A

A 35 3/4" 41 5/8"

B 15" 21 5/8"

C 49 5/8" 58 1/2"

D 10 3/8" 13 1/2"

E 13 3/4" 16 3/4"

F 41" 48"

G 41 1/4" 48 1/4"

H 68 1/2" 81 1/2"

FRAMING

Once the nal location has been determined,

observing height clearances for vent termina-

tion, you may construct framing using dimen-

sions shown in Figures 3 and 4, depending on

your installation.

If the appliance is to be installed directly on

carpeting, tile (other than ceramic) or any

combustible material other than wood oor-

ing, appliance must be installed on a metal

or wood panel extending full width and depth

of the appliance.

Nailing Tabs

Nailing

Tabs

CD36M-B CD42M-A

A 36 1/8" 40 1/8"

B 41 1/4" 48 1/4"

C 23 1/2" 25 5/8"

www.fmiproducts.com 119212-01E8

Fixed

Closed OpenableFixed

Closed

TERMINATION CAP AIR SUPPLY INLET GAS METERRESTRICTED AREA

(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or

balcony [*12" (30.5 cm) minimum]

B = clearance to window or door that may be opened

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

if between 10,000 and 50,000, 12" (30 cm) in Canada

if between 10,000 and 100,000; 12" (30 cm) in US if

greater than 50,000, 36" (91 cm) in Canada if greater

than 100,000]

C = clearance to permanently closed window

[minimum 12" (30.5 cm) recommended to prevent

condensation on window]

D = vertical clearance to ventilated soffit located above the

terminal within a horizontal distance of 24" (61 cm) from

the center-line of the terminal [18" (45.7 cm) minimum]

E = clearance to unventilated soffit [12" (30.5 cm) minimum]

F = clearance to outside corner (see below)

G = clearance to inside corner (see below)

H = *not to be installed above a meter/regulator assembly

within 36" (91.4 cm) horizontally from the center line

of the regulator

I = clearance to service regulator vent outlet [*72" (182.9 cm)

minimum]

J = clearance to non-mechanical air supply inlet to building

or the combustion air inlet to any other fireplace

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

if between 10,000 and 50,000, 12" (30 cm) in Canada

if between 10,000 and 100,000; 12" (30 cm) in US if

greater than 50,000, 36" (91 cm) in Canada if greater

than 100,000]

K = clearance to a mechanical air supply inlet [*In Canada,

6 ft. (1.83m) minimum; In US 3 ft. (91 cm) above if within

10 ft. (3 m) horizontally]

L = † clearance above paved side-walk or a paved driveway

located on public property [*84" (213.3 cm) minimum]

M = clearance under veranda, porch, deck

[*12" (30.5 cm) minimum ‡]

N = clearance above a roof shall extend a minimum of

24" (61 cm) above the highest point when it passes

through the roof surface and any other obstruction within

a horizontal distance of 18" (45.7 cm)

† vent shall not terminate directly above a side-walk or paved driveway which is located between two

single family dwellings and serves both dwellings*

‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.

Note: Local codes or regulations may require different clearances

A = 6" (15.2 cm)

Inside Corner

B = 6" (15.2 cm)

C = Maximum depth of 48" (121.9 cm)

for recessed location

D = Minimum width for back wall of

recessed location -

Combustible - 38" (965 mm)

Noncombustible - 24" (61 cm)

E = Clearance from corner in

recessed location-

Combustible - 6" (15.2 cm)

Noncombustible - 2" (5.1 cm)

Outside Corner Recessed Location

G = 12" (30.5 cm) minimum clearance

Balcony with No Side Wall

Combustible &

Noncombustible

H = 24" (61 cm)

J = 20" (50.8 cm)

Balcony with Perpendicular Side Wall

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Openable

Figure 5 - Minimum Clearances for Vent Terminations

PRE-INSTALLATION PREPARATION

Continued

www.fmiproducts.com

119212-01E 9

REQUIREMENTS FOR THE COMMONWEALTH OF

MASSACHUSETTS

For all side wall horizontally vented gas fueled

equipment installed in every dwelling, building or

structure used in whole or in part for residential

purposes, including those owned or operated by

the Commonwealth and where the side wall ex-

haust vent termination is less than seven (7) feet

above nished grade in the area of the venting,

including but not limited to decks and porches,

the following requirements shall be satised:

INSTALLATION OF CARBON

MONOXIDE DETECTORS

At the time of installation of the side wall horizon-

tal vented gas fueled equipment, the installing

plumber or gas tter shall observe that a hard

wired carbon monoxide detector with an alarm

and battery backup is installed on the oor level

where the gas equipment is to be installed. In

addition, the installing plumber or gas tter shall

observe that a battery operated or hard wired car-

bon monoxide detector with an alarm is installed

on each additional level of the dwelling, building or

structure served by the side wall horizontal vented

gas fueled equipment. It shall be the responsibility

of the property owner to secure the services of

qualied licensed professionals for the installation

of hard wired carbon monoxide detectors.

In the event that the side wall horizontally

vented gas fueled equipment is installed

in a crawl space or an attic, the hard wired

carbon monoxide detector with alarm and

battery back-up may be installed on the next

adjacent oor level.

In the event that the requirements of this

subdivision can not be met at the time of

completion of installation, the owner shall

have a period of thirty (30) days to comply with

the above requirements; provided, however,

that during said thirty (30) day period, a battery

operated carbon monoxide detector with an

alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required

in accordance with the above provisions shall

comply with NFPA 720 and be ANSI/UL 2034

listed and IAS certied.

SIGNAGE

A metal or plastic identication plate shall be

permanently mounted to the exterior of the

building at a minimum height of eight (8) feet

above grade directly in line with the exhaust

vent terminal for the horizontally vented gas

fueled heating appliance or equipment. The

sign shall read, in print size no less than 1/2" in

size, "GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS".

INSPECTION

The state or local gas inspector of the side

wall horizontally vented gas fueled equipment

shall not approve the installation unless, upon

inspection, the inspector observes carbon

monoxide detectors and signage installed in

accordance with the provisions of 248 CMR

5.08(2)(a) 1 through 4.

EXEMPTIONS: The following equipment is

exempt from 248 CMR 5.08(2)(a) 1 through 4:

• The equipment listed in Chapter 10 entitled

"Equipment Not Required To Be Vented"

in the most current edition of NFPA 54 as

adopted by the Board; and

• Product Approved side wall horizontally

vented gas fueled equipment installed in a

room or structure separate from the dwell-

ing, building or structure used in whole or

in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved

side wall horizontally vented gas equipment

provides a venting system design or venting

system components with the equipment, the

instructions provided by the manufacturer for

installation of the equipment and the venting

system shall include:

• Detailed instructions for the installation of

the venting system design or the venting

system components; and

• A complete parts list for the venting system

design or venting system.

Gas Equipment Venting System Not

Provided

When the manufacturer of a Product Ap-

proved side wall horizontally vented gas fu-

eled equipment does not provide the parts for

venting the ue gases, but identies "special

venting systems", the following requirements

shall be satised by the manufacturer:

•

The referenced "special venting system" in-

structions shall be included with the appliance

or equipment installation instructions; and

• The "special venting systems" shall be Prod-

uct Approved by the Board, and the instruc-

tions for that system shall include a parts list

and detailed installation instructions.

A copy of all installation instructions for all

Product Approved side wall horizontally

vented gas fueled equipment, all venting in-

structions, all parts lists for venting instruc-

tions, and/or all venting design instructions

shall remain with the appliance or equipment

at the completion of the installation.

www.fmiproducts.com 119212-01E10

INSTALLATION

WARNING: This gas replace

and vent assembly must be

vented directly to the outside. The

venting system must NEVER be

attached to a chimney serving a

separate solid fuel burning appli-

ance. Each gas appliance must

use a separate vent system. Do

not use common vent systems.

WARNING: Horizontal sec-

tions of this vent system require

a minimum clearance of 2" from

the top of the pipe and 1" mini-

mum to the sides and bottom.

Vertical sections of this system

require a minimum of 1" clear-

ance to combustible materials

on all sides of the pipe.

VENTING INSTALLATION

1. Install elbow to replace collar adapter

located on back of the unit at a 45° angle.

Slide elbow over collar and twist to lock.

Check to insure proper connection (see

Figure 6).

2. Continue to install remainder of pipe for

desired installation. Make sure each sec-

tion is twist-locked securely.

3. When installation of vent pipe is complete,

in stall vent termination. Depending on

location of your replace, you will vent

vertically or horizontally.

4. Allow 1" of pipe to protrude from internal

wall, depending on wall thickness. See

Figure 7, page 11.

Figure 6 - Venting Installation

Female

Locking

Lugs

Male

Locking Lugs

Vertical Flue

Restrictor

(For Vertical

Venting

Application)

WARNING: Read all instruc-

tions completely and thoroughly

before attempting installation.

Failure to do so could result in

serious injury, property dam-

age or loss of life. Operation of

improperly installed and main-

tained venting system could

result in serious injury, property

damage or loss of life.

NOTICE:Failure tofollow thesein-

structions will void the warranty.

VENTING INSTALLATION

PRECAUTIONS

Consult local building codes before beginning

installation. Installer must make sure to select

proper vent system for installation. Before

installing vent kit, installer must read this re-

place manual and vent kit instructions.

Only a qualied service person should install

venting system. The installer must follow

these safety rules:

• Wear gloves and safety glasses for

protection

• Use extreme caution when using ladders

or when on roof tops

• Be aware of electrical wiring locations in

walls and ceilings

The following actions will void the warranty

on your venting system:

• Installation of any damaged venting compo-

nent

• Unauthorized modification of the venting

system

• Installation of any component part not

manufactured or approved for use with the

replace.

• Installation other than as instructed by

these instructions

NOTICE:All Style Crest, Inc direct

vent replaces only approved

5/8" pipe components and ter-

minations.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels StyleCrest Cheminée intérieure

StyleCrest

StyleCrest Vexar C42MW Guide de démarrage rapide

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation