Studiobricks One Manuel utilisateur

One, OnePlus,

& OneXXL

Assembling

guide

Last update | January 2022

For safe usage

please observe

the following

All bricks are referenced therefore should be placed in

 certain order during assembly.

We recommend that you use  manual screwdriver to

avoid scratches.

Be very careful not to open the door while the cabin is

unnished. If there is no other option than to open the door

during assembling because you install the cabin between

walls, open it very carefully and balance the weight.

IMPORTANT! Please note that no part of the cabin

should touch the building except for the feet. Leave at least

5cm space between the cabin and the wall to avoid vibrations

and assure proper sound isolation properties

Installation, connection and commissioning must be

done by  qualied professional (according to IEC60050;

IEV195-04-01) with professional electrotechnical skills.

Inappropriate installation can lead to danger to life and

danger to the life of the users of the installation.

With improper installation you risk heavy material

damage e.g. through re. In case of  non properly done

installation, Studiobricks can’t be held liable in case of

damage of persons and material assets. Volt-free dismounting.

The carrier must unload the cabin on  flat floor, never

inclined such as an access ramp to  garage, for example,

the box could tip over and injure people.

It is suggested to have at least 3 people for the assembling

of this model as pieces are very heavy.

Caution in opening the box on the incorrect side as

parts may fall out.

Make sure there are no children or pets nearby during

the unpacking of the cabin.

During unpacking, remove the highest parts and those

on top of others, rst. Alternate parts on one side and

another to ensure the stability of the packaging. Any heavy

part that moves during unboxing can cause the entire

package to overturn.

Please follow the steps of this model carefully.

It is very important to level the floor well before begin-

ning the assembly. A poorly leveled cabin can jeopardize

the stability of the assembly and makes it challenging to

t the pieces correctly.

Make sure to adjust the feet of the booth well so it

keeps stable during the assembly.

IMPORTANT! The floor and the

ceiling frame come together,

make sure to separate them

before you start assembling.

Index

Precautions 2

Starting 4

Delivery 4

Unpacking 4

Parts 5

Tools 6

Organization 6

Diferences between Studiobricks One, 7

One Plus and One XXL

Assembly 8

Platform setup for Studiobricks One XXL

Building thestructureforStudiobricks One XXL

Platform setup for Studiobricks One/Plus 11

BuildingthestructureforStudiobricksOne/Plus

Common steps 14

Finishing 34

Moving your booth 44

Before the assembly

1. Starting

1.1 Delivery

Your Studiobricks One booth will arrive in  box.

NOTE! If you detect any damages on the box

during delivery please record these damages on

the shipping documents.

In case of damage  claim for reimbursement can be

done by the insurance company. Delivery company will

not be responsible for the removal of the empty box

and must be disposed by the receiver.

1.2 Unpacking

Open the box by unscrewing the lid on the marked

side labeled “open this side”.

Caution in opening the box on the incorrect

side as parts may fall out.

After taking all the pieces out please inspect carefully

that everything has arrived in good shape and that all

pieces are complete.

Before the assembly

List of parts for Studiobricks One XXL:

Bricks 16

Floor ring (with 8 battens) 1

Silentblocks 10

Central silentblocks 2

Floor carpet pieces 3

Roof ring 1

Cieling brick 1

Rubber parts 16

60cm vertical large battens 12

30 cm vertical short battens (level D) 4

Horizontal batten (A1, B1, C1, D1) 4

Square battens B 16

Square battens C 4

Door 1

Door handle 1

Ventilation kit (optional) 1

Cieling absorber (as part of the roof) 1

Led light 1

Cable port 1

Trim cable port 2

Voltage transformer (USA) 1

Paint pot 1

1.3 Parts

List of parts for Studiobricks One and One Plus:

Bricks 16

Floor (with 8 battens) 1

Silentblocks Studiobricks One/One Plus 5/7

Floor carpet piece 1

Roof ring 1

Cieling brick 1

Rubber parts 16

60cm vertical large battens 12

30 cm vertical short battens (level D) 4

Square battens A 4

Square battens B 12

Square battens C 4

Door 1

Door handle 1

Ventilation kit (optional) 1

Cieling absorber (as part of the roof) 1

Led light 1

Cable port 1

Trim cable port 2

Voltage transformer (USA) 1

Paint pot 1

IMPORTANT!

The floor and the ceiling frame come together, make sure to separate

them before you start assembling.

Before the assembly

1 . 4 Tools

To build this booth you will need the following tools: 

rubber mallet, snap blade utility knife,  screwdriver, 

spirit level and  stepladder.

.5 Organization

Please keep in hand all tools that will be needed

during the assembly. The order of assembly will be the

following:

1) Platform setup

2) Assembly of level A

3) Assembly of level B

4) Roof assembly

5) Electric Connection

6) Interior extras

Please note that each brick is labeled with  specic

letter and  number.The letters show in what level the

brick is meant to be at. The numbers is the position in

respect to the door. The rst brick from the left side

of the door is number 1.

Before the assembly

1.6 Diferences

between

Studiobricks

One, One Plus

and One XXL

Studiobricks One models have the same, therefore the

same assembling instructions, except for some small

diereneces:

1) The Studiobricks One Plus is the same as the

Studiobricks One, but with some 30 cm.

2) The Studiobricks One XXL is the same as the

Studiobricks One Plus, but the floor structure is

dierent to facilitate assembly and transportation:

a) The floor of the XXL model is made up of 

perimeter ring and 3 carpeted central pieces.

On the other hand, in Studiobricks One and

Studiobricks One Plus’ floor is  single piece

covered with carpet.

b) Studiobricks One XXL doesn’t come with A

battens, only B battens + horizontal batten instead.

We use Studiobricks One Plus booth as the

model for this assembly guide.

Studiobricks One and One Plus floor

Studiobricks One XXL floor

Assembly

2. Assembly

2.1 Platform

setup for

Studiobricks

One XXL

The Studiobricks One models are equipped with

silentblocks on the bottom of the ring floor piece.

Stack  felt piece in each silentblock to

prevent them from staining and denting the floor

over time.

First, put them in the holes underneath the floor level.

Then you need to level the ring floor platform by

adjusting the silentblocks.

Start by adjusting the silentblocks, then balance the

whole ring using  spirit level to ensure it is level.

Next adjust the silentblocks so they rest on the

floor. Again, use  spirit level to ensure the floor is

completely level.

You need to level the ring floor by adjusting

the silentblocks.

Felt

piece

Silent

blocks

IMPORTANT! The floor and the ceiling

frame come together, make sure

to separate them before you start

assembling.

LEVEL

DOWN

2.2 Start

building the

structure for

Studiobricks

One XXL

You will now go on slotting all the panels in

numerical order and clockwise. It´s easier if you

slot in panel A5  bit later.

We advise to tilt the piece  bit before placing

it in place. Use this little trick to t the following

bricks for level A.

Please note that you can change the A2 Brick

with the A4 Brick in case you want the wire shaft

and ventilator in the opposite side.

A1 brick:

Start with the A1 brick. Place it on the left side of the

entrance door as indicated by the image. You can now

start building the walls.

A2 brick:

Place brick A2 as seen in the image to the left, tting

it with the A1 brick.

A3 brick:

Place brick A3 as seen in the image to the left, tting

it with the A2 brick.

brick:

Assembly

Floor carpet panels:

Once you’ve completed level A except for A4 and A5

brick it’s time to place the 3 panels that make up the

floor. Like the wall bricks, the floor panels are made

of sound isolating materials to prevent sound from

scaping downwards.

We will start by placing the 2 panels of the end.

Next, we can place the center panel.

Be careful not to catch your ngers when

putting the central panel on the floor.

A4 brick:

Place brick A4 as seen in the image, tting it with the

A3 brick.

Central

panel:

brick:

Floor

carpet

panels

Assembly

Autres manuels pour One

Ce manuel convient aux modèles suivants

Table des matières

Manuels Produits de plomberie populaires d'autres marques

Weka

Weka 506.2020.00E Mode d'emploi

Kohler

Kohler K-6228 Instructions de montage

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manuel utilisateur

American Standard

American Standard DetectLink 6072121 Manuel utilisateur

Uponor

Uponor Contec TS Manuel utilisateur

Pfister

Pfister Selia 49-SL Manuel utilisateur

Fortis

Fortis VITRINA 6068700 Manuel utilisateur

Fortis

Fortis MILANO 78211JS Manuel utilisateur

Kohler

Kohler K-12183 Instructions de montage

Maxxus

Maxxus MX-M206-01 Manuel utilisateur

Moen

Moen 5922 Series Manuel utilisateur

Viega

Viega Prevista Pure 8512 Manuel utilisateur

Kohler

Kohler Centerset K-15240 Instructions de montage

Viega

Viega Prevista Dry 8522.33 Manuel utilisateur

Sanela

Sanela Lema SLP 59RB Manuel utilisateur

Elkay

Elkay EDF15AC Manuel d'installation

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manuel

baliv

baliv WT-140 Manuel utilisateur

studiobricks One Manuel utilisateur

Manuels Produits de plomberie populaires d'autres marques