Stryker Quantum 2000 Manuel utilisateur
Quantum 2000 Light Source
Model Number: Q2000
Operating Manual
VERSION PAGE
English
1
Nederlander 13
Fraqais
27
Deutsch
41
Italian0 55
Espagiiol 69
Light Source Menu
Service Manual
CONTENTS
Thank you for purchasing the Stryker Quantum 2000 Light Source, designed
by a leading worldwide manufacturer of illuminated diagnostic instruments. By
following the use and care guidelines given in this manual, you will be reward-
ed with years of dependable, trouble-free service from your new Light Source.
Read these instructions thoroughly before use.
System
Symbol
Descriptions..
....................... 1
Warnings and
Precautions..
............................ 2
System Description..
........................................
4
System
Set-up/Operation ................................ 5
Lamp Replacement .......................................... 6
Fuse Replacement .......................................... 8
Cleaning ............................................................ 9
Specifications
.................................................. 10
Troubleshooting Guide..
..................................
1 1
Maintenance and Repair.. ................................ 12
Warranty and Service ...................................... 12
Ordering Information ...................................... 12
REF
CAUTION
0
SN
Catalog Number
Attention: Read operating manual for warnings, precautions,
and instructions for use.
Dangerous Voltage: Refer servicing to qualified personnel.
Type B Equipment
Caution
-
Hot
Warning: Risk of fire. replace fuses as marked.
Light; Lighting; Illumination Intensity
Conformance to:
93/42/EEC
Medical Device Directive
Serial Number
INDICATIONS
Use of the Quantum 2000 Light Source is indicated for medical lighting
applications requiring a remotely located, high-quality white light.
This product must only be used by qualified medical personnel.
CONTRAINDICATIONS
The use of the Quantum 2000 Light Source is contraindicated for applica-
tions where high intensity light might burn or damage tissue; such as
for neonate transillumination and ophthalmic procedures. For further
contraindications, the user must also consult the operating manual of
the instrument being used with the Light Source in the medical procedure.
1
WARNINGS AND PRECAUTIONS
2
SYSTEM DESCRIPTION
The Quantum 2000 Light Source is used to supply high-quality, white light
for video and optical illumination systems. It accepts standard
ACMI
connectors.
PowerSwitch
Minimum
Light Output
Maximum
Light Output
Fiber Optic
Bundle Port
Control Knob
FRONT
AC Power Outlet
Fuse
Draw
Fan Grill
BACK
Lamp Access
Door
4
SET-UP AND OPERATION
After a 15-second warm-up period, the light output will stabilize at its
normal intensity.
1.
Plug the Quantum 2000 Light Source into a hospital-grade receptacle.
2. Turn the light-intensity control knob to its minimum position. Plug the fiber
optic bundle into the illuminator port and connect the opposite end to the
instrument.
3. Turn the power switch to the on position. The lamp will take 15 seconds to
complete its warm-up cycle.
4. Set light intensity to desired level.
5. Turn unit off when not in use.
NOTE: Do not restart lamp immediately after turning off.The lamp
may fail to start. If this occurs, turn the power switch off and wait
15 seconds before restarting the Quantum 2000 Light Source.
5
1.
Turn unit off and unplug the power cord from both the wall outlet and the
Quantum 2000 Light Source.
2. Remove the lamp access door from the bottom of the Quantum 2000
Light Source by loosening the thumbscrew and gently lifting the door
open. Leaving the wires attached, gently lay door aside to gain access
to the lamp.
3. Disconnect the lamp connector
assembly by pulling back on the
black connector.
-1
m
Black Connector
4. Remove the lamp from the holding
spring assembly by firmly grasping
the ceramic lamp base and pulling
the lamp gently toward the rear.
While pulling back, slide the lamp
up and over the tension spring and
out of the light source.
Ceramic Lamp Base
Tension
Springs
6
NOTE: Replace with Stryker lamp #502 220 176 only. Do not touch the
lamp itself, or the interior reflective surface of the lamp. Skin oils on the
lamp will cause premature lamp failure. Always hold lamp by the ceramic
connector base. Remove any grease or fingerprints with a clean cotton
swab moistened with alcohol. Do not leave any lint on the lamp.
5. To install a new lamp, grasp the lamp by the ceramic base and be
sure that the alignment pin on the lamp is pointing up. Gently slide the
lamp down into place between the holding spring assembly and the front
of the box, allowing the holding spring to help seat the lamp in the fixture.
Check to be sure that the
alignment pin on the lamp is
securely placed in the slot on
the fixture. When the lamp is
properly seated, you will be
able to rotate the lamp slight-
ly in either direction. If lamp
does not rotate at all, or
rotates freely, pull back gen-
tly and reposition lamp as
described above. Plug the
black connector assembly
wire back into the lamp.
---A-)-1
assembly
I
/
Be sure
alignment pin
and lamp are
properly seated
black connector
‘wire
6. Reattach the lamp door securely. The unit will not power up unless the
lamp door is seated properly.
7
FUSE REPLACEMENT
1.
Turn the unit off and remove the power cord from both the wall outlet and
the Quantum 2000 Light Source.
Fuse Holder
2. Use a small screwdriver to remove the fuse holder below the power cord
connector by releasing the spring-loaded snap connections.
3. Pull out the fuse holder.
4. Remove and replace with new fuses of the same type. There is no
required orientation of the fuses. Be sure to replace both fuses.
5. Reinsert the fuse holder by pressing it into the power connector until it
snaps into place.
6. If the new fuse blows, immediately contact Stryker Technical Service.
Fuses
Snap
Connections
7
8
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Stryker Équipement médical
Stryker
Stryker IsoTour Standard 2872 Manuel utilisateur
Stryker
Stryker LIFEPAK 20 Instructions d'installation
Stryker
Stryker Harmonic Ace+7 Manuel utilisateur
Stryker
Stryker Secure Connect Manuel
Stryker
Stryker altrix Manuel utilisateur
Stryker
Stryker 5050 Manuel utilisateur
Stryker
Stryker 3002 Manuel utilisateur
Stryker
Stryker sdc classic Manuel utilisateur
Stryker
Stryker ComfortGel SE 1805-034-300 Manuel utilisateur
Stryker
Stryker PneumoSure Manuel utilisateur
Stryker
Stryker ProCuity Bed Series Manuel utilisateur
Stryker
Stryker 1550 Manuel utilisateur
Stryker
Stryker 6100 Rugged M1 Manuel
Stryker
Stryker 1004 Manuel utilisateur
Stryker
Stryker 3002 Manuel utilisateur
Stryker
Stryker 2100 Manuel utilisateur
Stryker
Stryker 1080 Manuel utilisateur
Stryker
Stryker 721 Manuel utilisateur
Stryker
Stryker Restep Manuel utilisateur
Stryker
Stryker S3 MEDSURG BED Manuel utilisateur
