Struers Lavamin Manuel utilisateur
Lavamin
Pre-installation checklist
Doc. no.: 16237037_B_en-us
Date of release: 2023.03.23
Copyright
The contents of this manual are the property of Struers ApS. Reproduction of any part of this manual without
the written permission of Struers ApS is not allowed.
All rights reserved. © Struers ApS 2023.03.23.
2 Lavamin
1 Installation requirements
– Power supply
– Water supply
– Compressed air supply
– Water drain
– Workbench
2 Packaging specifications
X: 75 cm (29")
Y: 38 cm (15")
Z: 41 cm 16")
Weight 23 kg (51 lbs). The weight is stated on the
crate.
3 Location
CRUSHING HAZARD
Take care of your fingers when handling the machine.
Wear safety shoes when handling heavy machinery.
• Make sure that the following facilities are available:
– Power supply
– Water supply
– Compressed air supply
1 Installation requirements
Lavamin 3
Recommended workbench dimensions
Height
Width
Depth
Recommended: 80 cm (31.5")
70 cm (27.6")
80 cm (31.5")
• Place the machine on a rigid, stable workbench with a horizontal surface and an adequate
height.
• The machine must rest securely with all 4 feet on the table.
• To facilitate easy access for service technicians, allow sufficient space around the machine.
Illumination
Illumination: Make sure that the machine is adequately lit up. A minimum of 300 Lumen is
recommended to illuminate the controls and other work areas.
Ambient conditions
Operating environment Surrounding temperature 5-40°C (40-105°F)
Humidity 35-85% RH non-condensing
4 Lavamin
3 Location
4 Dimensions
Width: 317 mm (12.5")
Depth: 629 mm (24.8")
Height:
• Closed: 325 mm
(12.1")
• Open: 488 mm
(19.2")
Weight: 17 kg (37.5 lbs)
Front view
X: 317 mm
(35")
Z: 325 mm
(12.8")
4 Dimensions
Lavamin 5
Side view
X: 629 mm
(24.8")
Z: 488 mm
(19.2")
5 Recommended space
Space in front of the machine
• Make sure that there is enough room in front of the
machine.
100 cm (40”)
6 Transport and storage
If, at any time after the installation, you have to move the unit or place it in storage, there is a number
of guidelines we recommend that you follow.
• Package the unit securely before transportation. Insufficient packaging could cause damage to
the unit and will void the warranty. Contact Struers Service.
• We recommend that you use the original packaging and fittings.
6 Lavamin
5 Recommended space
6.1 Transport
CRUSHING HAZARD
Take care of your fingers when handling the machine.
Wear safety shoes when handling heavy machinery.
Note
We recommend that you keep all original packaging and fittings for future use.
To transport the machine safely, follow these instructions.
Preparing for transport
1. Disconnect the unit from the electrical power supply.
2. Remove any accessories.
3. Clean and dry the unit.
6.2 Storage
CRUSHING HAZARD
Take care of your fingers when handling the machine.
Wear safety shoes when handling heavy machinery.
Note
We recommend that you keep all original packaging and fittings for future use.
1. Disconnect the machine from the electrical power supply, water supply and compressed air
supply.
2. Check that there is no specimen holder or mover plate in the machine.
3. Clean and dry the unit before storage.
4. Place the machine and accessories in their original packaging.
Note
If the machine is not to be used for a longer period of time, wrap the machine in
plastic along with silica gel.
7 Unpack the machine
CRUSHING HAZARD
Take care of your fingers when handling the machine.
Wear safety shoes when handling heavy machinery.
7 Unpack the machine
Lavamin 7
Note
We recommend that you keep all original packaging and fittings for future use.
1. Cut the packing tape on the top of the box.
2. Fold out the side of the box (see the illustration).
3. Remove the loose parts.
4. Remove the unit from the box.
8 Lift the machine
CRUSHING HAZARD
Take care of your fingers when handling the machine.
Wear safety shoes when handling heavy machinery.
Note
Always lift the machine from beneath.
Weight
Lavamin 17 kg (37.5 lbs)
At the new location
1. Place the machine on a rigid, stable workbench with a horizontal surface and an adequate
height.
2. Make sure that the unit is level and rests securely on the workbench.
9 Safety specifications
Safety Circuit Categories/Performance Level
Rotation of the specimen holder PL d,Stop category0
Down movement of the hood PL c,Stop category0
8 Lavamin
8 Lift the machine
10 Power supply
WARNING
Switch off the machine, disconnect the electrical power cable and wait 5 minutes
before you dismantle the machine or install additional components.
ELECTRICAL HAZARD
Switch off the electrical power supply before installing electrical equipment.
The machine must be earthed (grounded).
Make sure that the actual electrical power supply voltage corresponds to the
voltage stated on the type plate of the machine.
Incorrect voltage can damage the electrical circuit.
Electrical data
Voltage/frequency 200 - 240 V 50-60Hz 100 - 120V 50-60Hz
Power inlet 1-phase (N+L1+PE) or 2-phase (L1+L2+PE)
Power consumption: Idle Max 2.5 W
140 W
@ 200-240V
2.5 W
140 W
@ 100-120V
Current 0.7 A
@ 200-240V
1.2 A
@ 100-120V
Power socket
The electrical power supply socket must be easy to access. The electrical power supply socket
must be located at a height ranging from 0.6 m to 1.9 m (2½” to 6’) above floor level. Not higher
than 1.7 m (5’ 6”) is recommended.
Note
The equipment is shipped with 2 types of electrical power cables. If the plug
supplied on these cables is not approved in your country, the plug must be
replaced with an approved plug.
Single-phase supply
The 2-pin plug (European Schuko) is for use on single-phase
electrical power connections.
The leads must be connected as follows:
Yellow/Green Earth (ground)
Black/Brown Line (live)
Blue Neutral
10 Power supply
Lavamin 9
2-phase supply
The 3-pin plug (North American NEMA) is for use on 2-phase
electrical power connections.
The leads must be connected as follows:
Green Earth (ground)
Black Line (live)
White Line (live)
Residual Current Circuit Breaker (RCCB)
Note
Local standards can override the recommendations for the main electrical power
supply cable.Always contact a qualified electrician to verify which option is suitable
for the local installation setup.
Residual Current Circuit Breaker
(RCCB)
Type A, 30 mA (or better) is recommended
Power the machine
ELECTRICAL HAZARD
Switch off the electrical power supply before installing electrical equipment.
The machine must be earthed (grounded).
Make sure that the actual electrical power supply voltage corresponds to the voltage
stated on the type plate of the machine.
Make sure that the fuse is set to the correct voltage setting.
Incorrect voltage can damage the electrical circuit.
1. Connect the electrical power cable to the machine (IEC
320 connector).
2. Connect the other end of the cable to the electrical power
supply socket.
Note
In countries with a 100 - 120V electrical power supply, you must change the setting
of the equipment.
– 115V: 100-120 V/50/60 Hz
– 230 V: 200-240 V/50/60 Hz (factory setting)
10 Lavamin
10 Power supply
Autres manuels pour Lavamin
1
Table des matières
Autres manuels Struers Équipement de laboratoire
Struers
Struers LaboPol-20 Manuel utilisateur
Struers
Struers LaboPol-35 Manuel utilisateur
Struers
Struers LaboPol-30 Manuel utilisateur
Struers
Struers LaboDoser-10 Manuel utilisateur
Struers
Struers Abramin Manuel utilisateur
Struers
Struers Lavamin Manuel utilisateur
Struers
Struers AbraPlan-30 Manuel utilisateur
Struers
Struers Xmatic Compact Manuel utilisateur
Struers
Struers Discotom-5 Manuel utilisateur
Struers
Struers LaboPol-60 Manuel utilisateur
Struers
Struers TegraDoser-5 Manuel utilisateur
Struers
Struers LaboForce-Mi Manuel utilisateur
Struers
Struers Labotom-20 Manuel utilisateur
Struers
Struers Epovac Manuel utilisateur
Struers
Struers Duramin-100 Manuel utilisateur
Struers
Struers LaboForce-100 Manuel utilisateur
Struers
Struers Xmatic Manuel utilisateur
Struers
Struers LaboPol-1 Manuel utilisateur
Struers
Struers Accutom-100 Manuel utilisateur
Struers
Struers LaboForce-3 Manuel utilisateur
Manuels Équipement de laboratoire populaires d'autres marques
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuel utilisateur
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuel utilisateur
NI
NI PXI-5422 Manuel
Collomix
Collomix Aqix Manuel utilisateur
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur
Ocean Insight
Ocean Insight FLAME-NIR+ Manuel utilisateur
