Strip Technology Strip-Tec 1000 Manuel utilisateur

STRIP-TEC

WIRE STRIPPER

MODEL 1000

Strip Technology, Inc.

3700 N. Commerce St

Fort Worth, TX 76106

(800) 426-4126

800.321.3396

nascoop.com

STRIP TECHNOLOGY

Strip Technology, a leader cable and wiring recovery systems, offer 4 patented wire

strippers. Built tough, to be efficient and dependable, at our manufacturing facility in Fort

Worth, Texas, Strip Technology can also custom build any cable/wire recovery system to

your specs. Call us at 1.800.426 .4126 or 1.817.626.1504 and ask how we can fill your wire

stripping needs.

Strip Technology is one of the many business ventures created by the Alexander family.

Founded by Bill Alexander, Sr. and now run by his immediate family, Ronnie, Bobby and

Bill Alexander Jr., Strip Technology is based on the family's tradition of quality at a

reasonable price.

Driven by the demand to conserve and noting that our world only has a finite amount of raw

materials, Strip Technology was born. Recycling is not only smart, in that it conserves

resources, but it also profitable, because raw materials are not needed to produce an end

product that you can recover. There is no pollution, no hazardous byproducts and no

manufacturing labor involved.

The Alexander’s base their integrity on 3 generations of family ownership and dedication to

you, the customer. Our company's no-nonsense approach and 'esprit de corp' attitude of our

employees only enhance the kind of workmanship we place into everything we manufacture.

Strip Technology has 4 patented wire strippers on the market today. Give us, or one of our

authorized dealers a call if you require any special applications. We can custom build a wire

stripper specifically for you.

TABLE OF

CONTENTS

SECTION ONE – INSTRODUCTION

1-1, Model 1000 S/N Plate

1-2, Specifications

1-3, Model 1000 Limited Warranty

SECTION TWO – FREIGHT NOTICE

2-1, Freight Notice

2-2,

Unpacking Wire Stripper

SECTION THREE – SAFETY PRECAUTIONS

3-1, General

3-2, Before Operating the Wire Stripper

3-3,

Observe Electrical Precautions

3-4,

Caution Labels

SECTION FOUR – OPERATIONS

4-1, Operations

A. Connect units to the proper power source as follows

B. Observe All Warning and Danger Signs

C. Start and Stop Buttons

D. Emergency Stop Button

E. Adjusting The Cutting Blades

F. Over Tightening of Cutter Blades

SECTION FIVE – MAINTENANCE and REPAIR

5-1 Maintenance

A. Service Points

SECTION SIX – PARTS ILLUSTRATIONS

Figure 1, Cutter System

Figure 2, Drive System

Figure 3, Electrical System - Single Phase - 120 volt

SECTION SEVEN – VENDOR LITERATURE

SECTION ONE

INTRODUCTION

1-1 Model 1000 Strip-Tec Wire Stripper

Strip Technology, Inc. machines are designed and built to give long and trouble-free

life, providing that you conduct the simple maintenance procedures detailed in this

manual.

Remember that removing the outer insulation cover off the wire can be hazardous.

Before operating the Wire Stripper, it is important that the operator reads the safety

instructions contained in this manual (section 3). Please ensure that your operators

are fully trained in the use of the Wire Stripper and that you should conduct periodic

safety reviews of the equipment’s safety features and warning labels.

If you need any further help or assistance, or with to order parts for the Wire Stripper

please contact your distributor or the manufacturer:

Strip Technology, Inc.

3700 N. Commerce St

Fort Worth, TX 76106

(800) 426-4126

SECTION ONE

INTRODUCTION

1-2 MODEL 1000 SERIAL NUMBER PLATE

Before operating the Wire Stripper the unit must be wired and grounded in

accordance with National Electrical Codes including any and all Local codes.

The VENT PLUG is to be installed on the GEAR REDUCER before starting this

product.

MOTOR:

Model Number _________________________

Voltage: _______________________________

Phase: _________________________________

Serial Number: __________________________

Supply Circuit: __________________________ Amps MAX

1-3 SPECIFICATIONS:

Motor: 1 HP, 110 volts, Single Phase

Production: Approx. 50 ft/minute

Machine Height: 37 inches

Machine Length: 46 inches

Wire Size: 1/16 to 1 inch diameter

Weight: 100 lbs

SECTION ONE

INTRODUCTION

1-4 MODEL 1000 LIMITED WARRANTY.

Strip Technology, Inc., (warrantor) warrant to the original consumer purchaser only that all

products manufactured or supplied by warrantor will be free from defects in material and

workmanship under normal use and service for the period of 90 days from the date of

purchase for all warranted products. (Proof of purchase required)

This warranty does not cover damage from normal wear and tear, accident, misuse, or lack of

reasonable and necessary maintenance and service, nor does it warranty the improper

installation or unauthorized repair, alteration, modification, or defects in the unit when product

is installed.

In the event of a warranted product defect, please call Strip Technology, Inc., with a

description of the defect. It is Strip Technology, Inc.’s option to repair or replace with

functionally equivalent product. Proof of purchase and the return of product may be required

for replacements. Such repair or replacement shall be at warrantor’s expense, but you shall

bear all other expenses, including, but not limited to, cost of removal, transportation, re-

installation, communication and any special service requested by you such as overtime labor,

ect. Repaired or replaced items carry only the un-expired portion of the original warranty.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN

DURATION TO THE SHORTER OF THE PERIOD PROVIDED BY LAW OR THE PERIOD OF THE

WARRANTY AND UNDER NO CIRCUMSTANCES SHALL STRIP TECHNOLOGY, INC., BE LIABLE FOR

INCIDENTIAL OR CONSEQUENTIAL DAMAGES SUSTAINED IN CONNECTION WITH THE PRODUCT.

THE EXPRESS WARRANTY ABOVE CONSTITUTES THE ENTIRE WARRANTY AND IS IN LIEU OF ALL

OTHERS EXPRESSED OR IMPLIED.

Some states to not allow the exclusion or limitation or consequential damages, or limitation on

how long an implied warranty lasts, so the above limited or exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary

from state to state.

Customer Service Department

800-426-4126 Phone

817-625-2207 Fax

Strip Technology, Inc.

SECTION TWO

PREPARATION FOR USE

2.1 FREIGHT NOTICE

If crate and Wire Stripper should arrive to your company damaged, immediately take

photos of damage and fill out the proper paper work with the freight company. Contact

the manufacturer Strip Technology, Inc. to get costs of damaged parts and report to the

freight company.

2.2 UNPACKING WIRE STRIPPER

CAUTION

Remove crate from around Wire Stripper and before

removing Wire Stripper off of crate base be sure

lifting device is correctly lifting Wire Stripper from

underneath the table frame because of being top

heavy.

Model 1000 Shipping Crate

SECTION TWO

PREPARATION FOR USE

2.3 PRELIMINARY SERVICING

After removing the Model 1000 Wire Stripper from its shipping crate, set the unit

in its proper operating position (see figure 2-1).

Figure 2-1 Model 1000 Wire Stripper

The Model 1000 Wire Stripper was shipped completely serviced except for the VENT

PLUG being installed.

To install VENT PLUG remove the pipe plug and install the VENT PLUG shown in figure

2-2.

VENT PLUG

Figure 2-2 Gear Box Vent Plug

SECTION THREE

SAFETY PRECAUTIONS

3.1 GENERAL:

It is impossible to compile a list of safety precautions covering all situations. However,

there are basic safety precautions that MUST be followed during your daily routine.

Safety is YOUR PRIME RESPONSIBILITY, since any piece of equipment is only as safe

AS THE PERSON OPERATING THE EQUIPMENT.

With this in mind, this information has been provided to assist the operator, in promoting

a safe working area for yourself and those around you. It is not meant to cover every

conceivable circumstance which could arise. It is intended to present basic safety

precautions that should be followed in daily operations.

You, the operator, are the only one who can be relied upon to assure the safety of

yourself and those around you. Be a PROFESSIONAL and follow the RULES of safety.

Be aware at all times that you are responsible for the safety of yourself, your co-workers,

the WIRE STRIPPER and everything around it.

Read and understand the Operator’s Section 4 before operating the WIRE STRIPPER.

3.2 BEFORE OPERATING THE WIRE STRIPPER:

Be sure that the operator has read and understood this manual.

Be sure that the operator always wears eye protection.

Be sure that the operator is wearing the proper protective clothing and boots.

Inspect the entire unit before each use for worn, loose, missing, or damaged parts.

Be sure that all protective cutter blades guard plate is in proper position (see figure 3-1),

wire guide plate (see figure 3-2 and drive shaft and gear cover (see figure 3-3) are in

place and properly installed.

Figure 3-1 Cutter Blade Guard Figure 3-2, Guide Plate Figure 3-3, Drive Shaft Cover

Check that all safety and warning notices are clean and legible.

SECTION THREE

SAFETY PRECAUTIONS

Use proper size guide hole for wire size being stripped.

When operating the Wire Stripper, operator must stand on end of unit where ON/OFF

Switch is for easy access (See figure 3-4).

Figure 3-4, ON-OFF Switch

3-3 OBSERVE ELECTRICAL PRECAUTIONS:

Wire Stripper must be wired and grounded in accordance with National Electrical Codes.

Do not use in damp or wet locations or expose to snow, rain, or water to avoid the

possibility of electrical shock.

Use extension cords specifically marked suitable for outdoor use.

Inspect the insulation and connectors on the Wire Stripper and extension cord before

each use. If there is any damage, DO NOT USE until damage is repaired by qualified

service personnel.

DO NOT use ON/OFF switch if not operating properly. Repairs to switch must be made

by qualified service personnel.

Keep extension cord clear of operator, and other obstacles, which may damage cord at

all times.

DO NOT expose to heat, oil, or sharp edges.

Avoid any body contact with any grounded conductor, to avoid electrical shock.

Table des matières

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser