StressVest SUICIDE VEST Manuel utilisateur
Page 1
SUICIDE VEST
Quick Setup Guide
®
1. Insert the two speakers into the speaker pouches on the Suicide Vest. Slide the pipe bomb
props in the pipe bomb straps.The pipe bomb props can be disassembled and re-assembled
by unscrewing the end caps to easily secure into the straps. Add the prop wires for extra
realism and secure them with the straps.
2. Connect the two auxiliary connectors found on the StressVest® Suicide Vest Flashbox to
each speaker unit.
Assembling/Setting Up the StressVest® Suicide Vest
3. Place the StressVest® Face Sensor connector
(input) to the Suicide Vest’s shoulder strap using
Velcro.
4.The StressVest® Suicide Vest is now assembled and ready to put on the Role Player. Adjust
the body strap to fit on the Role Player’s body.
Page 2
How to Use the StressVest® Suicide Vest
1. Power on the StressVest® Suicide Vest Flashbox and the two speaker units by
pressing and holding the power button for a few seconds until the status light
is illuminated.The StressVest® Suicide Vest is ready to be activated.To turn off,
press and hold the power button on the flashbox and speakers until the status
light is off.
2. Activate the StressVest® Suicide Vest by pressing the Push Button Activator.
The StressVest® Suicide Vest will produce a realistic audible pipe bomb sound
with a bright light flash for auditory and visual effects.
WARNING: Do not activate and flash the LED lights near the eyes. It may hurt the eyes.
3. During the activation, the StressVest® Suicide Vest will register a hit to any StressVest®
within its set “kill radius” range of 0-100ft (RF MODE). For some closed room, close quarter
scenarios, the FLASH MODE produces a short invisible IR light ash to activate StressVests® panels
within line of sight to a range of approximately 15 feet.
5.To integrate StressVest® Face Sensor (sold separately), connect the green connector to the
StressVest® Suicide Vest Flashbox’s Face Sensor connector (input).
Face Sensor
connector (input)
Pain penalty or vibration
IR Flash
or
RF Signal
4. When a StressVest® Face Sensor is connected to the StressVest® Suicide
Vest, the StressVest® Suicide Vest power/battery status light will turn blue for 10
seconds once the Role’s Player’s Face Sensor is hit with an IR laser.The Push Button
Activator will not activate the Suicide Vest while the status light is blue.
Charging Batteries
STRESSVEST® SUICIDE VEST FLASHBOX
When StressVest® Suicide Vest battery is running low, the battery/power light
indicator will turn red. Charge the StressVest® Suicide Vest using a mini USB Charger.
The battery/power light indicator will turn green when fully charged.
SPEAKERS
The two speakers on the StressVest® Suicide Vest need to be charged separately. Use orange
micro USB cable to charge the speakers.The power light button on the speakers will turn blue
when fully charged.
SETCAN CORPORATION
1080 Kingsbury Ave. Winnipeg, Manitoba R2P 1W5 | Toll Free 1-866-353-5055 | Ph. (204) 336-0011 | Fax (204) 586-2049
Settings
1. Select a mode from RF (Radio Frequency), Flash (IR LED) or both by pressing the MODE
button.The status light indicates what mode you are on.
2. Adjust the speakers volume by pressing the VOLUME button. Note:You may
also adjust the volume using the speaker’s volume buttons. For your convenience,
always have the volume setting on the speaker unit itself maxed out.
3. When RF and BOTH modes are selected, you can adjust the range (“kill radius”)
from 0-100 feet. Press the RF Range button to toggle between the five levels of
range. Level 1 - 0ft to level 5 - 100ft.
FLASH RF
Range
RF
Table des matières
Autres manuels StressVest Dispositif de protection
Manuels Dispositif de protection populaires d'autres marques
nxt
nxt BIA-nXt-DPC 1-22 Manuel utilisateur
TFortis
TFortis SG-Switch Manuel utilisateur
BERNINI DESIGN
BERNINI DESIGN Be172 Manuel utilisateur
Rayleigh Instruments
Rayleigh Instruments RI-ENERGYSET-3P-ESS-50-100 Manuel utilisateur
GE
GE Multilin 3 Series Manuel utilisateur
E.K.T.
E.K.T. ke-DP01 Manuel utilisateur
