Stout Designs TRAILBLAZER Manuel utilisateur
2020
TRAILBLAZER - Operation Manual
Stout Designs, LLC
1/1/2020
TRAILBLAZER –OWNER’S MANUAL
Operating tips: VERY IMPORTANT
• Always run TRAILBLAZER at full throttle when cutting.
• Make sure the kill switch somewhere close to you so you can shut the machine down in the event you need to. (i.e. if you
get the saw in a bind or your around bystanders.)
• If you get the saw in bind and the belts slip or start stalling the motor, the first reaction you should have is to reverse
backwards or use the kill switch.
• Always walk away from the blade side while the blades are running.
• Don't let debris build up to heavy on top of the motor as the debris could get hot and ignite if left on top of the engine.
• Try to always use 91 or better non-ethanol fuel.
• Always tighten your blades with an impact wrench. A hand wrench will not tighten them enough.
• Never tighten the set screw on the clutch assembly jaw coupling (this coupling is designed to slip if needed). All other
setscrews on the bearings, drive shaft jaw coupling and clutch housing can be tightened and should be checked prior to use.
picture of setscrew to never tighten to follow.
• Visually Check to make sure Blue Spider is locked in place as shown in picture to follow
Note: if used on public trails, roads or pathways, please always use with caution and always use a lead and
trail vehicle to alert any potential oncoming public vehicles that trail maintenance equipment is near.
BLUE SPIDER PROPERLY ENGAGED.
TURN STAINLESS STEEL RING TO
THIS POSITION IF FOR SOME REASON
IT IS NOT.
TRAILBLAZER
US PAT. D795,307
US PAT. 9,807,928
VERTICAL TRAIL TRIMMER
OPERATOR / SAFETY MANUAL
!WARNING!
Note the following before starting:
Please read the operator's manual carefully.
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Stout Designs, LLC product!
Today Stout Designs, LLC is striving to be one of the leading manufacturers in the world of
forest coppicing products for use on ATV’s, UTV’s, Golf Carts and small tractors, with quality
as our highest priority. The business concept is to develop, manufacture and market motor-driven
products for forestry and trail management. Stout Designs’ aim is to develop equipment that
insures ergonomics, usability and environmental protection.
We are confident that you will appreciate, with great satisfaction, the quality and performance of
our product for a very long time to come. The purchase of one of our products gives you access
to one of the most innovative products in trail/pathway clearing and limb/brush management
along with professional help with repairs and service if it ever becomes necessary. If the retailer
who sells your machine is not Stout Designs, LLC or one of our authorized dealers, ask for the
address of your nearest service dealer or the product can be returned to Stout Designs, LLC for
any repair needs.
It is our wish that you will be satisfied with your product and that it will be your companion for a
long time. Think of this operator′s manual as a valuable document. By following its content
(usage, service, maintenance, etc.), the life span and the second-hand value of the machine can
be extended. If you sell this machine, make sure that the operator′s manual is passed on to the
buyer.
Thank you for using a Stout Designs, LLC product.
Stout Designs, LLC has a policy of continuous product development and therefore reserves the
right to modify the design and appearance of products without prior notice.
! WARNING !
The machine is designed for trimming horizontally orientated overhanging branches 2” in
diameter or less along forestry trails, pathways and roads and is to be used only when area is
clear of bystanders, fellow workers or animals.
The only accessories you can operate with this equipment are ones provided by Stout Designs,
LLC and specifically designed for your exact unit.
Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication
that could affect your vision, your judgement or your co-ordination.
Shut down equipment engine prior to exiting the vehicle and visually ensure the blades have
stopped completely.
Ideal operating speed for the saw is 3200-3600 RPM. Although the saw will run at a higher
RPM the motor is designed to operate at a maximum RPM of 3600 and actually produces the
most torque between 3200-3600 RPM. Blades will begin to rotate at an RPM greater than 2000
RPM.
Wear personal protective equipment. See instructions under the “Personal protective equipment”
heading.
Never use a machine that has been modified in any way from its original specification.
Never use a machine that is faulty. Carry out the checks, maintenance and service instructions
described in this manual. Some maintenance and service measures must be carried out by trained
and qualified specialists. See instructions under the Maintenance heading.
All covers, guards and handles must be fitted before starting. Ensure that the spark plug cap and
ignition lead are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or animals come closer than 20 feet while
working. When several operators are working in the same area the safety distance should be at
least 50 feet.
Carry out an overall inspection of the machine before use. See the maintenance schedule. In
addition to this manual, a Service manual from the MOTOR manufacturer will be provided.
! WARNING !
Long-term exposure to noise can result in permanent hearing impairment. So always use
approved hearing protection.
! WARNING !
Under no circumstances may the design of the machine be modified without the permission
of the manufacturer. Always use original accessories. Non-authorized modifications and/or
accessories can result in serious personal injury or the death of the operator or others.
! WARNING !
A TRAILBLAZER can be dangerous if used incorrectly or carelessly, and can cause
serious or fatal injury to the operator or others. It is extremely important that you read
and understand the contents of this operator’s manual.
! WARNING !
Running an engine in a confined or badly ventilated area can result in death due to
asphyxiation or carbon monoxide poisoning.
! WARNING !
You must use approved personal protective equipment whenever you use the machine. Personal
protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if
an accident does happen. Ask your dealer for help in choosing the right equipment if questions
arise.
HEAD PROTECTION
Head protection should whenever you operate an ATV of any kind. Protecting yourself from
potential head injuries is a key element of safe equipment operation. A head injury can impair
you for life or it can be fatal. Wearing a safety helmet or hard hat is one of the easiest ways to
protect an your head from injury. Hard hats can protect yourself from impact and penetration
hazards as well as from electrical shock and burn hazards. For your protection, head protection
must be worn if the trees being cleared are taller than 2 m. Approved head protection must
comply with the ANSI Z89.1.
HEARING PROTECTION
Wear hearing protection that provides adequate noise reduction. Generally, the louder the noise,
the shorter the exposure time before hearing protection is required. For instance, you may be
exposed to a noise level of 90 dB for 8 hours per day (unless they experience a Standard
Threshold Shift) before hearing protection is required. On the other hand, if the noise level
reaches 115 dB hearing protection is required if the anticipated exposure exceeds 15 minutes.
For a more detailed discussion of the requirements for a comprehensive hearing conservation
program, see OSHA Publication 3074 (2002), “Hearing Conservation” or refer to the OSHA
standard at 29 CFR 1910.95, Occupational Noise Exposure, section (c).Approved devices should
have a NRR (Noise Reduction Rating) of 20db.
!WARNING!
Listen out for warning signals or shouts when you are wearing hearing protection. Always
remove your hearing protection as soon as the engine stops.
EYE & FACE PROTECTION
Always wear approved eye protection. Face protection should be worn whenever possible.
Protective eyeglasses have safety frames constructed of metal or plastic and impact-resistant
lenses. Side shields are available on some models. Face shields are transparent sheets of plastic
that extend from the eyebrows to below the chin and across the entire width of your head. Some
are polarized for glare protection. Face shields protect against nuisance dusts and potential
splashes or sprays of hazardous liquids but will not provide adequate protection against impact
hazards. Face shields used in combination with goggles or safety spectacles will provide
additional protection against impact hazards. Wearing face protection does not adequately
protect your eyes; you must also wear approved eye protection. Approved eye protection must
comply with the ANSI Z87.1.
GLOVES
Gloves should be worn when necessary, e.g. when fitting cutting attachments. If a hazard
assessment reveals that you face potential injury to hands and arms that cannot be eliminated
through engineering and work practice controls, you must ensure that you wear appropriate
protection. Potential hazards include skin absorption of harmful substances, chemical or thermal
burns, electrical dangers, bruises, abrasions, cuts, punctures, fractures and amputations.
Protective equipment includes gloves, finger guards and arm coverings or elbow-length gloves.
You should explore all possible engineering and work practice controls to eliminate hazards and
use PPE to provide additional protection against hazards that cannot be completely eliminated
through other means. For example, machine guards may eliminate a hazard. Installing a barrier
to prevent you from placing their hands at the point of contact between a table saw blade and the
item being cut is another method.
FOOT PROTECTION
Wear boots with steel toe-caps and non-slip sole. Safety footwear must meet ANSI minimum
compression and impact performance standards in ANSI Z41-1991 (American National Standard
for Personal Protection-Protective Footwear) or provide equivalent protection. Footwear
purchased before July 5, 1994, must meet or provide equivalent protection to the earlier ANSI
Standard (ANSI Z41.1-1967). All ANSI-approved footwear has a protective toe and offers
impact and compression protection. But the type and amount of protection is not always the
same. Different footwear protects in different ways. Check the product’s labeling or consult the
manufacturer to make sure the footwear will protect the user from the hazards they face.
Approved foot protection must comply with the ANSI Z41.1.
CLOTHING
Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and
branches. Always wear heavy, long pants. Do not wear jeweler, shorts, sandals or go barefoot.
Secure hair so it is above shoulder level.
FIRST AID KIT
Always have a first aid kit nearby.
Ce manuel convient aux modèles suivants
1
Table des matières
