Stockmaster Mezzalift Manuel utilisateur

CL/INST06

Assembly

Instructions

BEFORE USE:

see

User Instruction Manual

Defect as a result of incorrect

assembly will not be covered

under your product

warranty.

www.stockmastereurope.nl

IMPORTANT: To avoid assembly problems follow these instructions exactly.

Step 1 - On a level surface butt the two Mast sections together. (See illustration No. 1)

Step 2 - Fix the Large Mast Joining Plate to the two Mast sections using four of the M6 x 16 button head screws -

Finger tight only.

(See illustration No. 2)

Step 3 - Turn the Mast over. Locate the Small Mast Joining Plates and position them inside the Mast channel and

fasten using four of the M6 x 16 button head screws. Ensure Mast sections are correctly aligned and then tighten all

screws.

(See illustration No. 3)

Step 4 - Lift the Mast as shown cut and remove the Wire Tie then lay the Mast ﬂat on its back again. (See illustration

No. 4)

Step 5 -In the centre of the Mast Channel. Cut and remove the Black Wire Ties holding the chain bundle in position.

(See illustration No. 5)

Note: Do NOT cut the White Wire Tie.

Step 6 -Using the White Wire Tie. Pull the stored chain down the length of the mast untill taught. (See illustration

No. 6)

Step 7 - Loosen the Mast Roller at the base of the Mast (See illustration No. 7)

Step 8 - Using the 2 Black Wire Ties supplied. Tie the chain to the top of the Mast thru the holes A & B. Ensure the

White Wire Tie is located between these two tie positions. (See illustration No. 8)

Mast Assembly

www.stockmastereurope.nl

Illustration 1 Illustration 2

Illustration 3 Illustration 4

M6 x 16

Mast Assembly

www.stockmastereurope.nl

Illustration 5 Illustration 6

Illustration 7 Illustration 8

A B

Mast Assembly

www.stockmastereurope.nl

IMPORTANT: To avoid assembly problems follow these instructions exactly.

Step 1 - On a level surface lay the mast face-down as shown. (See illustration No. 1)

Step 2 - Remove the Nut from the Winch Shaft at A. Pull out the winch shaft and remove the Sproket. Carefully put

the Sproket, Shaft, Nut & Washer aside. Parts to be re-assembled in Step 4. (See illustration No. 2)

Step 3 - Place the Winch Body inside the opening on the back of the Mast. Insert the Winch Body at 45 degrees so

the Chain ﬁts inside the Winch Body.(See illustration No. 3)

Step 4 - Fix the Winch Mounting Bracket to the Mast at B & C using two of the M6 x 16 button head screws and nyloc

nuts.

Finger tight only.

(See illustration No. 4)

Step 5 - Adjust the Winch Mounting Bracket so you can slide the Sprocket back into place. Insert the Winch Shaft

at D and re ﬁt the washer and nut. Fix the Winch Mounting Bracket to the Mast at Eusing an M6 x 16 button head screw

and nyloc nut. Tighten the Winch Shaft and nut ﬁrmly then tighten the Winch Mounting Bracket screws and nuts at B, C,

& E (See illustration No. 5)

Illustration 1 Illustration 2

Winch Assembly

www.stockmastereurope.nl

Winch Assembly

Illustration 3 Illustration 4

Illustration 5

M6 x 16

DM6 x 16

www.stockmastereurope.nl

Mounting Bracket Assembly

IMPORTANT: To avoid assembly problems follow these instructions exactly.

Step 1 - Fit the upper Floor Support Angle to the Mast at A & B as shown using two of the M8 x 20 button head

screws and nyloc nuts. Screws facing up. Nuts on top. (See illustration No. 1)

Note: Upper Floor Support Angle can be ﬁtted upside down on the Mast if required for additional height adjustment.

Step 2 - Fit the Mast Cradle Bracket to the bottom of the Mast at C using an M6 x 16 button head screw and nyloc

nut. (See illustration No. 2)

Step 3 - Fix the two Upright Sections to the Base Bracket using four of the M8 x 20 button head screws and nyloc

nuts.

Finger tighten only

(See illustration No. 3)

Step 4- Measure the Vertical Height from the Lower Floor level to the Uppr ﬂoor level at the position the Mezz-a-lift

is to be intsalled. (See illustration No. 4)

Step 5 - Position the Base Assembly over the Mast Cradel Bracket. Measure the total length from the upper Floor

Support Angle to the bottom of the Base Assembly. Adjust the position of the base assembly to reﬂect the measurement

from Step 4. (See illustration No. 5)

Step 6 -Fix the Base Assembly to the Mast Cradel Bracket, thru the ﬁxing slots on both sides of the Upright

Sections using four of the M8 x 20 button head screws and nyloc nuts.

Finger tighten only.

(See illustration No. 6)

Illustration 1 Illustration 2

M8 x 20

M6 x 16

www.stockmastereurope.nl

Illustration 3 Illustration 4

Illustration 5 Illustration 6

Mounting Bracket Assembly

M8 x 20

www.stockmastereurope.nl

Instalation

IMPORTANT: To avoid assembly problems follow these instructions exactly.

Step 1 - Stand the Mezz-a-Lift into position placing the upper Floor Support Angle on the upper landing in the

required position. With someone supporting the unit, mark the ﬁxing positions A1 - A3 in the upper landing thru the

Floor Support Angle. Drill and ﬁx at these locations with appropriate ﬁxings.

Fixings not supplied

(See illustration No. 1)

Step 2 - Using a Spirit Level, level the Mezz-a-Lift front to rear and side to side (See illustration No. 2)

Step 3 - Mark the ﬁxing positions B1 - B4 in the lower ﬂoor thru the Base Bracket. Drill and ﬁx at these locations

with appropriate ﬁxings.

Fixings not supplied

(See illustration No. 3)

Step 4 -

Tighten ALL fasteners now

90°

Illustration 1 Illustration 2

www.stockmastereurope.nl

Tighten

ALL Fasteners

at this point

Instalation

Illustration 3

Table des matières

Autres manuels Stockmaster Système de levage

Stockmaster

Stockmaster Lift-Truk Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur