Sterling SVS4A-40CR Manuel utilisateur
OSCILLATION
FUNCTION
ADJUSTABLE
HEIGHT
140cm
3 SPEEDS ADJUSTABLE
TILT HEAD
Get the perfect airow
wherever you are
3 Speeds
Direct the airow to make
it suitable for your situation
Adjustable Tilt Head
Move the fan head up
or down for comfort
Adjustable Height
Swings 80 degrees
to distribute airow
more evenly
Oscillation Function
3 Speeds
80° Oscillation
Adjustable Tilt Head
Adjustable Height to 1.4m
40cm CHROME
PEDESTAL FAN
WITH METAL BLADES
Features:
Quick Start Guide:
Assembly
Assembling the Base
Place the Stand (13) on the Round Base (16), and insert the 4x Base Screws (15) through the
corresponding holes (insert from the top). (Fig.1)
Slide the decorative Stand Cover (14) over the Stand (13) and
place it in the recess on the Round Base (16). (Fig.4)
Carefully place the Stand Assembly upright on the floor.
Remove the Inner Tube (11) from the Stand by first gripping it and then removing the Height
Adjustment Screw (12) fully. (Fig.3)
Partially insert the Inner Tube (11) into the Stand (13), and
hold it in place while re-tightening the Height Adjustment
Screw (12). (Fig.5)
Replace the Motor-Stand Screw (10) and tighten it by hand
so that the Motor section doesn't come off the Stand when
lifted. (Fig.7)
Remove the Motor-Stand Screw (10) from underneath the
Motor Housing (9), then slide the Motor Housing assembly
onto the top of the Inner Tube (11). (Fig.6)
Holding the Base Screws (15) and Round Base (16) in place, tilt up to base to secure from
the underside.
Slide the Base Weight (17) over the 4 Base Screws (15), then secure the Base Weight (17) in
place with the 4x Butterfly Nuts (18). (Fig.2)
Fig.1 Fig.2 Fig.3
Fig.4
Fig.6 Fig.7
Fig.5
Please read the 'General Safety Instructions' section of the Instruction Manual before operating
the fan.
Assembling the Fan Head
Unscrew the Guard Retaining Nut (4) from the Motor Housing (9) by rotating it anticlockwise.
(Fig.8)
Position the Rear Guard (5) on the front of the Motor Housing (9); ensure that the handle is at
the top.(Fig.9)
Replace the Guard Retaining Nut (4) and hand-tighten it firmly.(Fig.10)
Undo the Blade Retaining Screw (3).
Place the Fan Blade (2) on the Motor Shaft (6) and push it back as far as it will go.
Now replace the Blade Retaining Screw (3) tightly to lock the Fan Blade (2) to the Motor Shaft
(6). (Fig.11)
Attached to one of the guards is the Guard Locking Screw & Nut (19). Remove these and keep
them safe. (Fig.12)
Open the Guard Locking Clips (20) of the Front Guard (1) fully. Hook the top of the Front Guard
(1) over the Rear Guard (5) and pull down to attach it. (Fig.13)
Fig.8
Fig.9
Fig.10
Fig.11
Fig.12 Fig.13
Assembly (cont.)
Assembling the Fan Head (cont.)
Manoeuvre the Front Guard (1) so that the screw holes at the bottom of both guards line up.
Loosely attach the Guard Locking Screw & Nut (19). (Fig.14)
(loosely) Fig.14 Fig.15 (tighten) Fig.16
Line up the two guards and then shut the Guard Locking Clips (20) to secure the two guards.
(Fig.15)
Now tighten the Guard Locking Screw & Nut (19) tightly. This completes the fan assembly.
(Fig.16)
Assembly (cont.)
For more information
please call 1300 366 155
or visit www.stirlingappliances.com.au
Model Specifications
Colour
Warranty
SVS4A-40CR
Chrome
1 year
Table des matières
Autres manuels Sterling Ventilateur
