Stenner Pumps ECON LD Manuel

ECON LD PUMP SERIES

INSTALLATION AND MAINTENANCE MANUAL

PERISTALTIC METERING PUMPS SINCE 1957

TO BE INSTALLED AND MAINTAINED BY PROPERLY TRAINED

PROFESSIONAL INSTALLER ONLY. READ MANUAL & LABELS

FOR ALL SAFETY INFORMATION & INSTRUCTIONS.

WARNING

2www.stenner.comEcon LD

Warranty and Service Policy ................................................................. 3

Safety Information ....................................... 4-6, 9-12, 14-18, 20-22, 24

Materials of Construction .................................................................... 7

Accessory Checklist............................................................................. 8

Flow Rate Outputs .......................................................................... 9-10

Installation................................................................................... 11-17

Troubleshooting ............................................................................ 18-20

Tube Replacement ........................................................................ 21-23

Cleaning the Point of Injection...................................................... 24-26

Exploded View and Parts ............................................................... 27-28

Mounting Template ............................................................................ 29

IMELD 031017

TABLE OF CONTENTS

LIMITED WARRANTY

Stenner Pump Company will for a period of one (1) year from the date of purchase (proof

of purchase required) repair or replace – at our option – all defective parts. Stenner is not

responsible for any removal or installation costs. Pump tube assemblies and rubber

components are considered perishable and are not covered in this warranty. Pump tube

will be replaced each time a pump is in for service, unless otherwise specified. The cost of

the pump tube replacement will be the responsibility of the customer. Stenner will incur

shipping costs for warranty products shipped from our factory in Jacksonville, Florida. Any

tampering with major components, chemical damage, faulty wiring, weather conditions,

water damage, power surges, or products not used with reasonable care and maintained in

accordance with the instructions will void the warranty. Stenner limits its liability solely to

the cost of the original product. We make no other warranty expressed or implied.

RETURNS

Stenner offers a 30-day return policy on factory direct purchases. Except as otherwise

provided, no merchandise will be accepted for return after 30 days from purchase. To

return merchandise at any time, call Stenner at 800.683.2378 for a Return Merchandise

Authorization (RMA) number. A 15% re-stocking fee will be applied. Include a copy of your

invoice or packing slip with your return.

DAMAGED OR LOST SHIPMENTS

Check your order immediately upon arrival. All damage must be noted on the delivery

receipt. Call Stenner Customer Service at 800.683.2378 for all shortages and damages

within seven (7) days of receipt.

SERVICE & REPAIRS

Before returning a pump for warranty or repair, remove chemical from pump tube by

running water through the tube, and then run the pump dry. Following expiration of the

warranty period, Stenner Pump Company will clean and overhaul any Stenner metering

pump for a minimum labor charge plus necessary replacement parts and shipping. All

metering pumps received for overhaul will be restored to their original condition. The

customer will be charged for missing parts unless specific instructions are given. To return

merchandise for repair, call Stenner at 800.683.2378 or 904.641.1666 for a Return

Merchandise Authorization (RMA) number.

DISCLAIMER

The information contained in this manual is not intended for specific application purposes.

Stenner Pump Company reserves the right to make changes to prices, products, and

specifications at any time without prior notice.

TRADEMARKS

Santoprene®is a registered trademark of Exxon Mobil Corporation.

AquaShield™is a trademark of Houghton International.

USA and Canada 800.683.2378, International 904.641.1666 Econ LD

WARRANTY AND CUSTOMER SERVICE

4www.stenner.comEcon LD

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment,

basic safety precautions should always be followed,

including the following:

1.READ AND FOLLOW

ALL INSTRUCTIONS.

2.WARNING - To reduce the risk of

injury, do not permit children to use

this product unless they are closely

supervised at all times.

3.WARNING - Risk of Electric Shock.

Connect only to a branch circuit

protected by a ground-fault circuit

interrupter (GFCI). Contact a qualified

electrician if you cannot verify that

the receptacle is protected by a GFCI.

4.WARNING - To reduce the risk of

electric shock, replace damaged

cord immediately.

5.SAVE THESE INSTRUCTIONS.

USA and Canada 800.683.2378, International 904.641.1666 Econ LD

SAFETY INFORMATION

Warns about hazards that CAN cause death, serious personal

injury, or property damage if ignored.

ELECTRIC SHOCK HAZARD

Pump supplied with grounding power cord and attached plug. To reduce risk of

electrical shock, connect only to a properly grounded, grounding type receptacle.

Install only on a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI). For

locations other than US and Canada, pump must be supplied through a residual

current device (RCD) with a rated residual operating current < 30 mA.

DANGER DE CHOC ÉLECTRIQUE

La pompe est dotée d’un cordon d’alimentation avec mise à la terre muni d'une fiche.

Pour réduire le risque de choc électrique, branchez uniquement sur une prise

correctement mise à la terre. Installez uniquement sur un circuit protégé par un

disjoncteur différentiel. En dehors des États-Unis et du Canada, la pompe doit être

alimentée par un dispositif à courant différentiel résiduel (RCD) fonctionnant à <30 mA.

DO NOT alter the power cord or plug end.

DO NOT use receptacle adapters.

DO NOT use pump with a damaged or altered power cord or plug end. Contact the

factory or an authorized service facility for repair.

HAZARDOUS VOLTAGE

DISCONNECT power cord before removing motor cover for service. Electrical service

by trained personnel only.

EXPLOSION HAZARD

This pump is not explosion proof. DO NOT install or operate in an explosive environment.

RISK OF EXPOSURE

Potential for burns, fire, explosion, personal injury, or property damage. To reduce risk

of exposure, the use of proper personal protective equipment is mandatory.

RISK OF FIRE HAZARD

DO NOT install or operate on any flammable surface.

RISK OF CHEMICAL OVERDOSE

To reduce risk, follow proper installation methods and recommendations. Check your

local codes for additional guidelines.

To reduce the risk of injury, do not permit children to use this

product. This appliance is not to be used by persons with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction.

6www.stenner.comEcon LD

SAFETY INFORMATION continued

Warns about hazards that WILL or CAN cause minor personal

injury or property damage if ignored.

PLUMBING

Metering pump installation must always adhere to your local plumbing codes and

requirements. Be sure installation does not constitute a cross connection. Check

local plumbing codes for guidelines.

NOTICE: Indicates special instructions or general mandatory action.

This metering pump is portable and designed to be removable from the plumbing

system without damage to the connections.

Before installing or servicing the pump, read the pump manual for all safety

information and complete instructions. The pump is designed for installation and

service by properly trained personnel.

Installation and product must adhere to all regulatory and compliance codes

applicable to the area.

This is the safety alert symbol. When displayed in this manual or on the

equipment, look for one of the following signal words alerting you to the

potential for personal injury or property damage.

Acceptable for indoor and outdoor use.

Acceptable pour une utilisation aussi bien à l’intérieur qu’à l’extérieur.

Electrical installation should adhere to all national and local codes. Consult a licensed

professional for assistance with proper electrical installation.

Removing power from pool/spa recirculation pump must also remove power from pump.

The use of an auxiliary safety device (not supplied), such as a flow switch or sensor,

is recommended to prevent feed pump operation in the event of a recirculation

pump failure or if flow is not sensed.

Point of injection should be beyond all pumps, filters, and heaters.

Maximum liquid temperature = 40°C.

USA and Canada 800.683.2378, International 904.641.1666 Econ LD

MATERIALS OF CONSTRUCTION

All Housings

Polycarbonate

Pump Tube

Santoprene®*, FDA approved

Pump Head Rollers

Polyethylene

Check Valve Duckbill

Santoprene®*, FDA approved

Suction/Discharge Tubing & Ferrules

Polyethylene, FDA approved

Suction Line Strainer

PVC, NSF listed with ceramic weight

Tube & Injection Fittings

PVC or Polypropylene, NSF listed

Connecting Nuts

PVC, NSF listed

All Fasteners

Stainless Steel

*Santoprene®is a registered trademark of Exxon Mobil Corporation.

8www.stenner.comEcon LD

ACCESSORY CHECKLIST

Contents

3 Connecting Nuts 1/4"

3 Ferrules 1/4" or 6 mm Europe

1 Injection Check Valve

1 Weighted Suction Line Strainer 1/4"

1 20' Roll of Suction/Discharge Tubing

1/4" White or UV Black OR 6 mm White Europe

1 Additional Pump Tube

1 Installation Manual

USA and Canada 800.683.2378, International 904.641.1666 Econ LD

Item Number Pump Roller Approximate Ounces Pressure Milliliters Pressure

Prefix Tube Assembly Turndown Ratio per Hour psi per Hour bar

E10LHM M White 50:1 0.04–2.4 80 1.3–70.0 5.5

E10LHF F White 50:1 0.11–8.1 80 3.2–240.0 5.5

Approximate Outputs @ 50/60Hz

FLOW RATE OUTPUTS

The output on the variable speed pump can be adjusted

via the potentiometer on the side of the pump.

Turning the potentiometer fully counterclockwise turns

the pump off.

Turning the potentiometer clockwise gradually increases

the speed to 100% at the full clockwise position.

Graduations are approximate.

DO NOT set

potentiometer in

gray area of scale

NOTICE: The information within this chart is solely intended for use as a guide.The output data is an approximation based on

pumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump

Company recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their outputs.

NOTE: Injection check valve included with pumps rated 80 psi (5.5 bar) maximum.

INSTALLATION

ADDITIONAL SAFETY INSTRUCTIONS

NOTICE: Indicates special instructions or general mandatory action.

Read all safety hazards before installing or servicing the pump. The pump is

designed for installation and service by properly trained personnel.

Use all required personal protective equipment when working on or near a

metering pump.

Install the pump so that it is in compliance with all national and local plumbing

and electrical codes.

Use the proper product to treat potable water systems, use only additives listed or

approved for use.

Inspect tube frequently for leakage, deterioration, or wear. Schedule a regular pump

tube maintenance change to prevent damage to pump and/or spillage.

Pump is not recommended for installation in areas where leakage can cause

personal injury or property damage.

10 www.stenner.comEcon LD

Table des matières

Autres manuels Stenner Pumps Pompe à eau

Stenner Pumps

Stenner Pumps M128 Series Manuel d'installation

Stenner Pumps

Stenner Pumps Classic Series Manuel utilisateur

Stenner Pumps

Stenner Pumps E10T1F Manuel

Stenner Pumps

Stenner Pumps Classic Series Manuel

Stenner Pumps

Stenner Pumps QuickPro Classic Series Manuel utilisateur

Stenner Pumps

Stenner Pumps M128 Series Manuel

Stenner Pumps

Stenner Pumps Classic Series Manuel

Stenner Pumps

Stenner Pumps E20MH Manuel

Stenner Pumps

Stenner Pumps SVP Series Manuel utilisateur

Stenner Pumps

Stenner Pumps S Series Manuel utilisateur

Stenner Pumps

Stenner Pumps ECON T Series Manuel

Stenner Pumps

Stenner Pumps QuickPro Classic Series Manuel utilisateur

Stenner Pumps

Stenner Pumps Classic Series Manuel utilisateur

Stenner Pumps

Stenner Pumps QuickPro Manuel utilisateur

Stenner Pumps

Stenner Pumps S Series Manuel

Stenner Pumps

Stenner Pumps S Series Manuel utilisateur

Stenner Pumps

Stenner Pumps S10P Series Manuel

Stenner Pumps

Stenner Pumps SVP Series Manuel

Stenner Pumps

Stenner Pumps 45MHP2 Series Manuel

Stenner Pumps

Stenner Pumps S Series Manuel

Stenner Pumps

Stenner Pumps ECON FP Series Manuel

Stenner Pumps

Stenner Pumps SVP4L1 Manuel

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur