Steelcraft DS5 Manuel utilisateur

DS5 RUNNING BOARD

20-22 Gladiator

Page 1 of 5 5/20/22 (SL)

PARTS LIST:

Universal Mounting Tubes ( 85’’)

10mm Nylon Lock Nuts

Left Plastic End Caps

10mm x 24mm x 2.2mm Flat Washers

Right Plastic End Caps

8mm Nylon Lock Nuts

DS5 Drop Steps

8mm x 35mm Hex Bolts

Front Mounting Brackets

8mm Hex Nuts

Center Mounting Brackets

8mm x 28mm x 3mm Flat Washers

Rear Mounting Brackets

8mm x 24mm x 2mm Flat Washers

Front Support Brackets

8mm Lock Washers

Center & Rear Support Brackets

6mm Nylon Lock Nuts

Spacers

6mm x 25mm Hex Bolts

T-Bolts

6mm x 22mm x 2mm Flat Washers

10mm x 30mm Hex Bolts

PROCEDURE:

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY. ASSISTANCE IS RECOMMENDED.

1. Start installation toward the front of the Passenger/Right side of the vehicle. Locate the factory threaded

mounting hole in the bottom of the floor, (Figure 1).

2. Select the Front Support Bracket. Attach the Support Bracket to the pinch weld with (2) 6mm Hex Bolts,

(4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts. (Figure 2). Select the Front Mounting Bracket,

Attach Front Mounting Bracket to the threaded hole in the of the floor panel with (1) 8mm Hex Bolt, (1)

8mm Lock Washer and (1) 8mm Flat Washer, (Figure 3). Attach the Support Bracket to the Mounting

Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut, (Figures 3).

Do not tighten hardware

3. Move to the #2 center location, (Figure 5). Repeat Steps 2to attach the Center Mounting Bracket and

the Center & Rear Support Bracket, (Figures 5—6).

4. Move to the rear location, (Figure 7). Repeat Steps 2to attach the Rear Mounting Bracket and the

Center & Rear Support Bracket to the rear location. (Figures 7—8)

(2) Front Support Brackets

(2) Universal Mounting Tubes

(4) DS5 Drop Steps

(4) Center & Rear Support Brackets

Front Mounting

Bracket

Center Mounting

Bracket

Rear Mounting

Bracket

Rear Mounting

Bracket

Center Mounting

Bracket

Front Mounting

Bracket

DS5 RUNNING BOARD

20-22 Gladiator

Page 2 of 5 5/20/22 (SL)

5. Select the Universal Mounting Tube. Select (6) 8mm T-bolts. Insert the T-bolts into the rear and bottom

channels of the Universal Mounting Tube, (Figure 9). Guide the T-bolts to the general position of the

Mounting Brackets.

6. Take (8) 8mm T-bolts. Insert the T-bolts into the front channels of the Universal Mounting Tube (Figure

10). Each front channel should have (4) T-bolts, which corresponds to the holes on the DS5 Drop

Steps.

7. Attach the DS5 Drop Steps to the Universal Mounting Tube. Each DS5 Drop Step uses (2) 8mm Plate

Washers and (4) 8mm Nylon Lock Nuts, (Figure 11—12). Do not tighten hardware. While the hardware

is not tightened, the Drop Steps will slide along the length of the channels.

8. Take (2) Plastic End Caps. Insert the correctly oriented Plastic End Caps onto the ends of the Universal

Mounting Tube, (Figure 13). It is recommended to secure one end and to use a rubber mallet to

carefully tap the Plastic End Caps into place on the other end. Inspect the installed Plastic End Caps to

see if they are facing the correct direction.

9. Attach the Universal Mounting Tube to the Mounting Brackets. Each Mounting Bracket uses (2) 8mm

Flat Washers, (2) 8mm Lock Washers and (2) 8mm Hex Nuts, (Figure 14). Do not tighten hardware.

10. Level and adjust the Universal Mounting Tube and tighten all hardware.

11. Adjust the DS5 Drop Steps by sliding them to the desired positions. Tighten all hardware to secure the

Drop Steps in place.

12. Repeat Steps 1—11 to attach the other Running Board.

13. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the

finish. Use only mild soap to clean the Running Boards.

Front

(Fig 1) Passenger/Right front location

(2) 6mm Hex Bolts

(4) 6mm Lock Washers

(2) 6mm Flat Washers

(Fig 2) Attach the Front Support

Bracket to the pinch trim

DS5 RUNNING BOARD

20-22 Gladiator

Page 3 of 5 5/20/22 (SL)

8mm Hex Bolt

8mm Lock Washer

8mm Flat Washer

10mm Hex Bolt

10mm Nylon Lock Nuts

(2) 10mm Flat Washer

(Fig 3) Attach the Front Mounting Bracket to

the front location; Attach the Front Support

Bracket to the Mounting Bracket

(Fig 4) Brackets attached to the

front mounting location

Front

(Fig 5) Passenger/Right 2nd

center location

(Fig 6) Brackets attached to the

center mounting location

DS5 RUNNING BOARD

20-22 Gladiator

Page 4 of 5 5/20/22 (SL)

(Fig 9) Insert T-bolts into the rear and

bottom channels on the universal

mounting tube.

Rear Channel

Bottom Channel

Front Channels

(Fig 10) Insert T-bolts into the Front

channels on the universal mounting tube.

Rear

(Fig 7) Passenger/Right rear

mounting location

(Fig 8) Brackets attached to the

rear mounting location

DS5 RUNNING BOARD

20-22 Gladiator

Page 5 of 5 5/20/22 (SL)

(Fig 11) Attach the Drop Steps to the front

channels of the Universal Mounting Tube.

(Fig 12) Attach the Drop

Steps to the 8mm T-bolts.

(2) 8mm Nylon Lock Nuts

(1) 8mm Plate Washer

(Fig 13) Attach the Plastic End Cap to the

end of the Universal Mounting Tube.

(1) Plastic End Cap

(2) 8mm Flat Washers

(2) 8mm Lock Washers

(2) 8mm Hex Nuts

(Fig 14) Universal Mounting Tube

attached to the Mounting Bracket.

Table des matières

Autres manuels Steelcraft Accessoires automobiles

Steelcraft

Steelcraft 213900 Manuel utilisateur

Steelcraft

Steelcraft Elevation Bull Nose Front Bumper Manuel utilisateur

Steelcraft

Steelcraft DS5 Manuel utilisateur

Steelcraft

Steelcraft 60-11380 Manuel utilisateur

Steelcraft

Steelcraft DS5 Manuel utilisateur

Steelcraft

Steelcraft 50320 Manuel utilisateur

Steelcraft

Steelcraft 223200 Manuel utilisateur

Steelcraft

Steelcraft DS5 Manuel utilisateur

Steelcraft

Steelcraft hd10410 Manuel utilisateur

Steelcraft

Steelcraft DS5 RUNNING BOARD Manuel utilisateur

Steelcraft

Steelcraft DS5 Manuel utilisateur

Steelcraft

Steelcraft EVO3 Manuel utilisateur

Steelcraft

Steelcraft 40-15020 Manuel utilisateur

Steelcraft

Steelcraft Fortis Manuel utilisateur

Steelcraft

Steelcraft STX100 Manuel utilisateur

Steelcraft

Steelcraft DS5 Manuel utilisateur

Steelcraft

Steelcraft EVO3 Manuel utilisateur

Steelcraft

Steelcraft HEAVY DUTY BULL NOSE FRONT BUMPER Manuel utilisateur

Steelcraft

Steelcraft DS5 Manuel utilisateur

Steelcraft

Steelcraft HD11370RW Manuel utilisateur

Steelcraft

Steelcraft 2011-15 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur