Steelcase Elective Elements Fixed Modesty Panel Manuel utilisateur

Elective Elements, Walden - Fixed Modesty Panel used on

a Freestanding Desk, Meeting or Extended Bullet Worksurface

3/16" Drill Bit

Floating 2/3-height modesty panel

attached to a Desk Table.

See page 10.

5/32" Drill Bit

Full-height modesty panel

sits proud of the storage unit

back or support back.

See page 4.

2/3-height modesty panel

sits proud of the underworksurface

storage back panels.

See page 6.

Inset modesty panel

between two underworksurface

storage cabinets.

See page 2.

2/3-height modesty panel

attached to an adjustable-height leg.

See page 8.

Floating 2/3-height modesty panel

attached to a Meeting or Extended

Bullet Worksurface. See page 10.

NOTICE

Steps for correct installation of

soft close drawers

Pull LH and RH suspensions to full extents

Find and disengage rear posts, LH and RH

Align drawer suspensions and install

1134607001

Soft close mechanism

can be damaged if this

step is skipped.

RH post is

shown here

in yellow Page 1 of 10

P/N 939500227

Doc # 108322 Rev J

If you have a problem, question, or request, call

your local dealer, or Steelcase Line 1 at

888.STEELCASE (888.783.3522)

for immediate action by people who want to help you.

(Outside the U.S.A., Canada, Mexico, Puerto Rico,

and the U.S. Virgin Islands, call: 1.616.247.2500)

Or visit our website: www.steelcase.com

Grand Rapids, MI 49501

U.S.A.

Printed in U.S.A.

INSET MODESTY PANEL

1. Turn worksurface over onto a clean,

soft surface.

2. Locate holes in pedestal end panels

and drill through.

3. Install pedestals onto worksurface

as shown. For more details, refer to

assembly direction 939500237.

Align pedestals flush with

front and sides of worksurface.

(4) screws per pedestal

through holes in stretchers,

1-1/2" pan head

Locate (2) pilot holes

in each pedestal, then

drill them through.

Page 2 of 10

P/N 939500227

Doc # 108322 Rev J

4. Lower modesty panel into position

between pedestals, then install onto

worksurface.

A) Install connecting bolts into holes in the

worksurface.

B) Lower modesty panel into position.

C) Insert cam locks and secure with a

half turn.

5. Make sure modesty panel is aligned

vertically, then secure to pedestals with

screws through holes drilled in step 2.

6. Carefully turn assembly over and

adjust leveling glides as needed.

CONNECTING BOLT 4a

Be sure to use

this set of holes.

(2) screws per pedestal,

# 10-12 x 1" pan head

Page 3 of 10

P/N 939500227

Doc # 108322 Rev J

FULL HEIGHT MODESTY PANEL

1. Locate predrilled holes in

worksurface, then install modesty panel.

A) Install connecting bolts into holes in

the worksurface.

B) Lower modesty panel into position.

C) Insert cam locks and secure with a

half turn.

2. Remove drawers (if any) from

pedestals.

CONNECTING

BOLT

Be certain to use

this set of holes.

To remove drawers

push lever down on one

side, and up on the other.

Drill pilot holes .197" (5mm) dia.

x .512" (13 mm) deep 24.5" 2.3"

49.0"

59.9"

66.25"

90.75"

.472"

1.675"

FRONT OF WORKSURFACE

NOTE: If your modesty panel is not the same length as your

worksurface, or if you ordered the wrong combination of

worksurface/modesty, you will need to drill your own

cam pin holes in the bottom of the worksurface.

Use the dimensions shown above.

Page 4 of 10

P/N 939500227

Doc # 108322 Rev J

3. Drill (2) holes through pedestal back

panels in the approximate locations

shown.

4. Position pedestals onto worksurface

so that fronts are flush with front and side

edges of worksurface and flush with

modesty panel at the rear.

Refer to assembly direction 939500237

for more information on installing

the pedestals.

5. Secure modesty panel to pedestals

through holes in stretchers and back

panels.

6. Carefully turn assembly over and

reinstall drawers. Position pedestals

flush with modesty panel

and with front and

sides of worksurface

(with drawer fronts installed).

FRONT VIEW

5Secure modesty panel to

back panel of pedestals with

(2) #10 x 1-1.500" screws,

each pedestal.

REAR VIEW

Locate (2) holes

in stretchers in back

of pedestal as shown,

then drill through back

panel of pedestal.

3/16" Drill Bit

Page 5 of 10

P/N 939500227

Doc # 108322 Rev J

2/3 HEIGHT MODESTY PANEL

1. Remove drawers (if any) from

pedestals.

2. Drill (4) holes through pedestal

back panels in the approximate

locations shown.

3. Fit finished back panels onto

pedestals as shown.

4. Secure with (4) screws each

through holes drilled in step 2.

Locate finished back panels

flush with pedestal end panels

and centered side to side.

PEDESTALS SHOWN UPSIDE DOWN

(4) screws per pedestal,

#10 x 1-1/2" pan head.

REAR VIEW

Locate (4) holes

in stretchers in back

of pedestal as shown,

then drill through back

panel of pedestal.

To remove drawers

push lever down on one

side, and up on the other.

Page 6 of 10

P/N 939500227

Doc # 108322 Rev J

5. Locate predrilled holes in

worksurface, then install modesty

panel.

A) Install connecting bolts into

holes in the worksurface.

B) Lower modesty panel into

position.

C) Insert cam locks and secure

with a half turn.

6. Install pedestals onto

worksurface as shown. For more

details, refer to assembly

direction 939500237.

7. Drill (2) holes through the two

rear panels of each pedestal.

8. Secure modesty panel to

pedestals with (2) screws each

pedestal.

When the drawers are reinstalled

pedestals will align with front and side

edges of worksurface, and with modesty panel.

Be certain to use

the rear set of holes.

CONNECTING

BOLT

FRONT VIEW

Drill through rear

and finished back

panels of pedestal,

into modesty panel. 78(2) screws per

pedestal, # 10-12

x 2" pan head.

Page 7 of 10

P/N 939500227

Doc # 108322 Rev J

1. Carefully turn worksurface over

onto clean, soft surface.

2. Remove drawers, then install pedestal

to worksurface as shown.

Refer to assembly direction 939500237

for more detailed information.

3. Install legs as shown.

Refer to assembly direction 939500235

for more detailed information.

4. Use 5/8" flat head screws to attach (2)

brackets to modesty panel.

A) Install top bracket to dimensions shown.

B) Locate bottom bracket approximately

9" (229 mm) below top bracket.

2/3-HEIGHT MODESTY PANEL

attached to an ADJUSTABLE-HEIGHT LEG

3-1/2"

(89 mm)

1-7/8"

(48 mm)

(229 mm)

NOTE: The bottom bracket

may have one or two holes.

2/3-HEIGHT

MODESTY PANEL

Align pedestal

(when drawer fronts

are in) flush with front

and sides of worksurface.

#10 x 1-1/4"

flat head screws

(10 per bracket).

Outer surface

of leg will align

with corner of

worksurface.

3/4"

(18.4 mm)

(both sides)

Align rear leg with

pedestal back panel.

#10 x .625"

flat head black Page 8 of 10

P/N 939500227

Doc # 108322 Rev J

NOTE: The top bracket

must have two holes.

FRONT VIEW

Locate (2) holes approximately

as shown, then drill through back

panel of pedestals using a 3/16"

drill bit. There will be a gap

between modesty panel

and worksurface.

Gap depends on

leg extension.

Secure modesty panel to pedestal

back panel with (2) screws,

#10-12 x 1-3/4" pan head.

5. Remove outer extrusion from leg.

6. Position outer extrusion in brackets so that

it is aligned with top of modesty panel.

7. Using the hole in top bracket as a guide,

drill a 5/32" dia. pilot hole through outer

extrusion just enough to mark location.

Be careful not to drill through or create

a dimple in front of leg by applying too

much pressure.

8. Put outer extrusion back in place and drill a

5/32" dia. hole through and into black bracket.

9. Remove outer extrusion and finish drilling

hole through black bracket.

10. Replace outer extrusion and secure

by tightening set screws.

11. Mount modesty panel onto leg and secure

with one screw into top bracket.

Measure to make sure modesty panel

is level with worksurface.

12. Locate and drill (2) holes through the two

rear panels of pedestal.

13. Make sure modesty panel is parallel with

worksurface, then secure to pedestal through

holes in back panel.

14.Carefully flip assembly over and adjust

glides as needed.

Align modesty panel

with leg extrusion.

Use an allen wrench

to tighten set screws. 10

Align

outer extrusion

flush with

modesty panel.

OUTER EXTRUSION

Drilled

Hole

#10 x 3/8"

truss head

Page 9 of 10

P/N 939500227

Doc # 108322 Rev J

Locate brackets then drill pilot

holes with a 5/32" dia. drill bit.

2/3 HEIGHT MODESTY PANEL

attached to a MEETING or EXTENDED

BULLET WORKSURFACE or a DESK TABLE

1. Carefully turn worksurface over onto clean, soft

surface.

2. Refer to assembly direction # 939501982 to install

disc column.

3. Install (2) L-brackets onto modesty panel (for panels

72" and wider, locate a third L-bracket at center of panel).

a) shows the locating dimensions for

installing the modesty panel flush with worksurface.

b) install brackets at this dimension when you are

suspending the modesty panel 1-1/2" from the

worksurface.

NOTE: Modesty panel needs to be mounted upside

down from normal orientation.

NOTE: The leg of the L-bracket with a hole nearest the

bend mounts to worksurface.

4. Install modesty panel to worksurface in desired

location with (2) screws, each bracket.

#10 x 7/8" truss

head screws

(2 per bracket)

3a 13-1/2"

(343 mm) both sides

2-1/2"

(64 mm)

FLUSH MOUNTED MODESTY PANEL

(25 mm)

SUSPENDED MODESTY PANEL

For Meeting and Extended Bullet Worksurfaces

the modesty panel can "float", or be located in

various positions to meet the needs of the user.

Center

of holes

Page 10 of 10

P/N 939500227

Doc # 108322 Rev J

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Steelcase Matériel de bureau

Steelcase

Steelcase Details Airtouch Manuel utilisateur

Steelcase

Steelcase Montage In Manuel utilisateur

Steelcase

Steelcase Turnstone Small Office Solution Set Manuel utilisateur

Steelcase

Steelcase Wood Selections Worksurface Mise à jour du firmware

Steelcase

Steelcase Avenir Movable Walls PAB-9 Joining Panels Manuel utilisateur

Steelcase

Steelcase Avenir Panel Manuel utilisateur

Steelcase

Steelcase Specific Solution for Answer Curved Corner... Manuel utilisateur

Steelcase

Steelcase TouchDown2 Manuel utilisateur

Steelcase

Steelcase Avenir PAB-4 Joining Panel Manuel utilisateur

Steelcase

Steelcase a3 CeramicSteel Sans Manuel utilisateur

Steelcase

Steelcase Pathways Privacy Screen Infill Manuel utilisateur

Steelcase

Steelcase FlipTop Twin Manuel utilisateur

Steelcase

Steelcase V.I.A. FEIJA2V Manuel utilisateur

Steelcase

Steelcase media:scape Kiosk Manuel utilisateur

Steelcase

Steelcase Series 5 Manuel utilisateur

Steelcase

Steelcase Turnstone Smoke Manuel utilisateur

Steelcase

Steelcase Elective Elements Powerway SPB89 Manuel utilisateur

Steelcase

Steelcase CF Intro Mise à jour du firmware

Steelcase

Steelcase Avenir PAB-3 Manuel utilisateur

Steelcase

Steelcase Turnstone Conference Space Solution Set Manuel utilisateur

Steelcase

Steelcase Context Mise à jour du firmware

Steelcase

Steelcase Brody Desk Manuel

Steelcase

Steelcase Migration SE Boundary Screen Manuel utilisateur

Steelcase

Steelcase UAW60 Manuel utilisateur

Manuels Matériel de bureau populaires d'autres marques

silen

silen Space 2 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products LD Series Manuel utilisateur

SHFL

SHFL DECK MATE BLACKJACK Manuel utilisateur

DROMEAS

DROMEAS LINE Manuel utilisateur

Siemens

Siemens HIPATH 2000 Manuel utilisateur

VITRA

VITRA Stefan Hürlemann Dancing Wall Manuel utilisateur

BISLEY

BISLEY Glide V2 Manuel utilisateur

fully

fully Haven Manuel utilisateur

Plus

Plus NF-20 Manuel utilisateur

OCEE DESIGN

OCEE DESIGN SASS-0100 Manuel utilisateur

NanaWall

NanaWall CSW75 Manuel utilisateur

Vivo

Vivo DESK V000C Manuel utilisateur

ABB

ABB 2TKA002145G1 Manuel utilisateur

PolyVision

PolyVision Flow Manuel utilisateur

MBM

MBM FC-10 Manuel utilisateur

Wiremold

Wiremold V2400 Series Manuel utilisateur

Vivo

Vivo PP-3-T072D Manuel utilisateur

BuzziSpace

BuzziSpace BuzziNest Booth Manuel utilisateur