STATESMAN GH61SS Manuel utilisateur
Please read these instructions carefully before use and retain for future reference.
Before switching on your appliance – Always check for any damage that may have been caused in transit.
Instruction Manual
GH61SS | 60cm 4 Zone Gas Hob Stainless Steel
Serial Number:
2
CONTENTS
Important Safety Instructions.................................. 2 - 3
Specication..................................................................4
Appliance Overview.......................................................4
Installation ............................................................. 5 - 10
Operating Instructions......................................... 11 - 12
Cleaning and Maintenance.................................. 13 - 14
Fuse Replacement ......................................................14
Disposal Information ...................................................14
Trouble Shooting Guide...............................................15
IMPORTANT SAFETY INSTRUCTIONS
Read and follow all of the instructions even if you feel you are familiar with the product, and
nd a place to keep this manual handy for future reference.
Important: This product is intended for domestic household use only.
When using gas appliances, basic safety precautions should always be followed:
1. Only a registered CORGI gas safe engineer can install, connect or repair this appliance. Do not
install or operate the appliance if it has been damaged.
2. Ensure the appliance is installed according to the installation instructions provided.
3. Do not change the specications or modify this appliance.
4. Prior to installation, ensure that the gas supply conditions (nature of the gas and gas pressure)
are compatible with the appliance.
5. Before installing ensure to turn o the gas and electricity supply to the appliance.
6. Check the voltage of the appliance matches the household voltage, which is located on the
rating label.
7. All appliances containing any electrical components must be earthed.
8. When installing, ensure that the gas pipe and electrical cable do not touch any part of the
appliance.
9. Ensure that the gas pipe or connectors are not bent or blocked by any other appliances.
10.The appliance is not intended to be operated by means of an external timer or remote control.
11.This appliance should only be used by adults.
12.Cleaning and user maintenance shall not be made by children.
13.Children shall not play with the appliance.
14.This appliance can be used by persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
15.Never leave the appliance unattended when in use.
16.Always ensure children are not left alone or unattended in the area of the appliance.
17.This appliance should not be used to warm or heat the room.
18.No combustible material or products should be placed on this appliance at any time.
3
19.It is not recommended to use plastic or aluminium foil dishes on the appliance.
20.Care should be taken when using this appliance as the cooker top can become extremely hot.
21.Do not allow clothing or any items other than suitable cookware contact with the appliance.
22.Ensure saucepan handles do not overhang burners that are switched on as they may become
hot.
23.It is not recommended to store anything on top of the appliance.
24.After use, always ensure that burners are switched o.
25.After use the appliance will stay hot for some time, even after it is switched o. Keep children
well away at all times.
26.Do not store ammable liquids and materials on or near the appliance.
27.Ensure that the kitchen is well ventilated or a mechanical extractor hood is tted.
28.It is not recommended to use this appliance if it comes into contact with water or with wet
hands.
29.Do not spray aerosols in the vicinity of the appliance whilst in operation.
30.When frying foods always try to ensure that food is as dry as possible as frost or moisture on
food may cause hot fat to bubble up and over the sides of the pan.
31.Do not try to move a pan of hot fat, always allow to completely cool.
32.The manufacturer shall not be responsible for any damages to persons or property caused by
incorrect installation or use of the appliance.
WARNING: In the event of a re, do not take any risks. If safe, turn the burner o, leave the
building and call 999. Never throw water over it and do not tackle the re yourself.
WARNING: In the event of a gas leak, stop using the appliance and ensure that all control
knobs are set to the o position. Open a window to ventilate and leave the room and contact a
registered CORGI gas safe engineer by the use of a neighbours phone or a mobile phone but not in
the vicinity of the appliance. Do not switch on/o any electrical appliances including lights. Gas can
have the smell of rotten egg or garlic.
4
Supplier Name
Model
Type of Hob
Pan Support
Top Plate
Dimensions (H x W x D) mm
Ignition Device
Type of Ignition
Gas Connection
Electric Supply
Energy Eciency Per Gas Burner
Statesman
GH61SS
Gas
Cast Iron
Stainless Steel
90 x 590 x 510
Continous Ignition
Electricity Cord
G1/2 Thread
220 - 240V, 50Hz/60Hz, 0.6W
G20 20mbar 54.95%
Triple Crown
57.38%
Semi Rapid
Burner
53.74%
Auxiliary
N/A
APPLIANCE OVERVIEW
1. Triple Crown Burner
2. Semi-rapid Burner
3. Control Knobs
4. Auxiliary Burner
Accessories
TECHNICAL SPECIFICATION
1
2
3
4
Bracket (4) Sealing Strip (4) Screw (4) Injector (5) Gas Pipe Bend (1)
Energy Eciency Per Gas Hob
Triple Crown
(Top left)
3.6kW
Semi Rapid x2
(Rear & front right)
1.75kW
Auxiliary
(Front left)
1kW
Burner Power
5
INSTALLATION
This appliance should only be installed by a registered CORGI gas safe engineer. Before installing
the appliance ensure that the area that you have selected is suitable and allows enough ventilation
for the appliance. The appliance can be tted into a kitchen unit or 600mm wide worktop, providing
that the stated minimum distances are allowed. Ensure that the selected worktop or unit and all
surrounding materials are made of non-ammable materials. Install a mechanical ventilation device.
Important: Always ensure the appliance is well ventilated and the air inlet and outlet are not
blocked.
Product Dimensions
W (mm) D (mm) H (mm)
590 510 90
6
• Cut a hole in the worktop that corresponds with the above diagram.
• The edges of the hob must be a minimum distance of 60mm from the rear wall.
• 700mm between the highest point of the hob surface (including the burners) and the underside of
any horizontal surface directly above it.
• 400mm between the hob surfaces, providing that the underside of the horizontal surface is in line
with the outer edge of the hob.
• The underside of the horizontal surface must be at least 50mm away from the outer edges of the
hob.
• 50mm clearance around the appliance and between the hob surface and any combustible
materials.
• You must have a gap of a minimum of 25mm and a maximum of 74mm between the underneath
of the appliance and any surface that is below it.
45 mm
FO 0813
400mm
560mm
490mm
400mm
700mm
0in.
0mm
60mm
0mm
M
2
60
7
Top View Bottom View
Important: Ensure the worktop is heat-resistant to avoid deformation caused by the heat radiation
from the burners.
• Remove the pan supports, the burner lid and ame spreader and carefully turn the appliance
upside down and place onto a cushioned mat. Taking care not to damage the ignition devices
and ame safety devices.
• Apply the provided Sealing Strip around the edge of the appliance. Ensuring not to leave a gap
or overlapping the sealing agent.
• Locate the screw holes on the base of the appliance.
• Place the bracket over the matching holes and secure with a screw ensuring to allow the bracket
to move.
• Carefully turn the hob back over and then gently lower into the cut
hole.
• On the underneath of the hob, adjust the brackets into a position that
secures the appliance to the worktop or unit. Screw can now be fully
tightened.
(A) SEALING STRIP
(C)S CREW (B)B RACKET
WARNING: Do not use a silicon sealant to seal the appliance
against the worktop or unit. This will make it dicult to remove the
appliance from worktops or units in the future, particularly if it needs
to be serviced.
8
Connecting to the Gas Supply
WARNING: This appliance must be installed by a registered CORGI gas safe engineer. The
appliance must be installed and connected in accordance with the manufacturer’s instructions and
to the relevant British Standards.
Note: This appliance is supplied to run on LPG and natural gas. Conversion for use on LPG and natural gases must
only be undertaken by a registered CORGI gas safe engineer.
seal
G1/2"Femalecoupler
Thegasrail
seal
Thegasrail
NG > LPGLPG > NG
Gas supply replacement and installation guidelines:
• It is law that all gas appliances are installed by competent persons in accordance with the
current edition of the Gas Safety Installation and Use Regulations.
• It is in your interest and that of safety to ensure compliance with the law.
• In the UK, GASSAFE registered installers work to safe standards of practice. The appliance
must also be installed in accordance with the current edition of BS 6172. Failure to install the
appliance correctly could invalidate the warranty, liability claims and lead to prosecution.
I3+(28-30/37) G30 Butane at28-30mbar and G31 Propane at 37mbar
I3B/P(30) G30 Butane and G31 Propane at 30mbar
BE, CH, CY, CZ, ES, FR, GB, GR, IE, IT, LT, LU, LV, PT, SK, SI
I2H/I2E/I2E+
BE, CY, DK, EE, GB, HU, IT, LT, NL, NO, SE, SI, SK, RO, HR,
TR, BG, IS, LU, MT, FI
G20 M ethane at 20mbar
II2H3+ CH, CZ,ES,GB,GR,IE, IT,PT,SI
G20 at 20mbar, G 30 B utane a t 28-30mbar a nd G 31
Propane at 37mbar
II2H3B/P(30)
AT,CH,CZ,DK,ES,FI,GB,GR,IE,IS,IT,PT,SE,SI,SK,DE,LU,GE,FR
G20 at 20mbar, G30 Butane and G31 Propane at 30mbar
II2E+3+
CH,CZ,DK,FI,GR,SE,SI,SK
BE, FR
G20/G25 a t 20/25mbar, G 30 B utane a t 28-30mbar and
G31 Propane at 37mbar
II2H3B/P
I2H: G20 Methane at 20mbar
I3B/P: G30 butane and G31 propane at 30mbar CH,CZ,DK,FI,GR,SE,SI,SK
II2H3+ CH, CZ,ES,GB,GR,IE, IT,PT,SI
I2H: G20 Methane at 20mbar
I3+: G30 butane at 30mbar and G31 propane at 37mbar
II2E+3+ BE, FR,
I2E: G20 Methane at 20mbar
I3+: G30 butane at 30mbar and G31 propane at 37mbar
9
Gas Adjustment
All adjustments when converting from one gas to another must be done by a registered CORGI gas
safe engineer.
WARNING: Ensure the gas and electricity supply to the appliance are switched o before
making any adjustments to the appliance.
Change the Injector of the Burners
• Remove the pan support, burner lid and ame spreader.
• Unscrew the injector using a 7mm box spanner and replace with new injector correct for the new
gas supply. Ensuring that the new injector is rmly tightened.
• Carefully reassemble all the Burner Cap, Burner Crown and Flame Spreader.
Injector
GH61SS
10
WARNING: Do not dismantle the Gas Tap Shaft: In the event of a malfunction, change the
whole tap.
• Before replacing the Flame Spreader and Burner Cap, ensure that the Injector is not blocked.
• A full operational test and a test for possible leaks must be carried out after a gas conversion.
• After completing conversion, the quailied gas engineer will need to mark “V” on the right gas
category to match with the setting on the rating plate. Remove the previous setting mark.
Control handle
Sealing ring
Tap
Important: For butane/propane gas, the adjusting screw must be tightly screwed in.
• Ret the control knobs to each Gas Tap.
• Test the ame by quickly turning the Control Knob from maximum to minimum, if the ame goes
out then you will need to make further adjustments to the gas ow.
• Repeat the process again until the gas ow is correct.
Adjustment of Minimum Level of the Flame
• Ignite the burner and set to MIN
• Remove the Control Knob and place a small bladed screwdriver in the centre of the Gas Tap
Shaft.
• Adjust until a steady ame is reached, about 3 – 4mm and does not extinguish when the Control
Knob is turned down to MIN.
• Repeat this procedure for all burners
Table des matières
Autres manuels STATESMAN Plaque
STATESMAN
STATESMAN GH75GB Manuel utilisateur
STATESMAN
STATESMAN GH60GB Manuel utilisateur
STATESMAN
STATESMAN GH75SS Manuel utilisateur
STATESMAN
STATESMAN ECH30TC Manuel utilisateur
STATESMAN
STATESMAN ECH60DC Manuel utilisateur
STATESMAN
STATESMAN ECH77TC Manuel utilisateur
STATESMAN
STATESMAN GH60WH Manuel utilisateur
STATESMAN
STATESMAN ECH60TC Manuel utilisateur
STATESMAN
STATESMAN ESH60SS Manuel utilisateur
