StarTech.com 1UCABCONS17 Manuel utilisateur
1UCABCONS
1UCABCONS17
1UCABCONS19
Manual Revision: 02/10/2011
Cabinet Console
For the most up-to-date information, please visit: www.startech.com
*actual product may vary from photo
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names
and/or symbols of third-party companies not related in any way to StarTech.com. Where they
occur these references are for illustrative purposes only and do not represent an endorsement of
a product or service by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct acknowledgement
elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.
Instruction Manual i
Table of Contents
Introduction ..............................................................................................................................1
System Requirements ............................................................................................................2
Assembly ....................................................................................................................................5
Installation .................................................................................................................................10
Connecting to a USB Controlled Computer .............................................................10
Connecting to a PS2 Controlled Computer ..............................................................11
Connecting to a KVM Switch .........................................................................................11
Operation ...................................................................................................................................12
Front Panel Functions .......................................................................................................12
Keyboard Replacement .........................................................................................................13
Touchpad Replacement ........................................................................................................14
Specications ............................................................................................................................15
Technical Support ...................................................................................................................17
Warranty Information ............................................................................................................17
Screen Quality & Pixel Policy ...............................................................................................17
Instruction Manual 1
Introduction
Thank you for purchasing a StarTech.com 1U Cabinet Console. This console
oers the ultimate in computer management, especially for applications
where space is at a premium.
The console drawer can be pulled out from the rack for operation, on sliding
rails that latch in the extended position; when not in use, the Active Matrix
TFT display can be folded down, locked, and secured while pushed in. With
dierent rear bracket & extension kits, the console can be mounted on rack
cabinets of various depths.
Features
• 1UCABCONS: Flip-open 15” TFT LCD panel supports
1024 x 768 @60/70/75
1UCABCONS17: Flip-open 17” TFT LCD panel supports
1280 x 1024 @60/70/75
1UCABCONS19: Flip-open 19” TFT LCD panel supports
1280 x 1024 @60/70/75
• Standard 19” 1U rack drawer
• Modular design
• Full 105 key, low-prole, sturdy keyboard built-in
• Standard connectors for PC connection
• Supports replaceable keyboard, mouse and module selection
• Locking mechanism locks the drawer when pulled out, pushed in or
folded down
• For rack cabinets with depth from 20” (50cm) and up (with appropriate rear
bracket and extension kit)
• Quick and easy installation
• Optional KVM switches available
Instruction Manual 2
System Requirements
The following are required to install the console:
• 1U Cabinet Console - assembled “LCD panel + keyboard + mouse
pad” drawer
• Rear bracket & extension kit - This kit contains two pieces of rear
brackets and two extensions. Make sure you have the correct kit to t
the depth of your cabinet.
Note: the following length is measured between front and rear poles,
inside the rack cabinet not the outside depth of a rack
Please see diagram on the following page
Front pole to rear
pole distance
( Depth )
1UCABCONS 1UCABCONS17 1UCABCONS19
cm inch cm inch cm inch
Minimum 59 23.2 59 23.2 59 23.2
Maximum 96 37.8 96 37.8 123 48.4
Front pole to rear
pole distance
( Depth )
CABCONS30KIT CABCONS42KIT
cm inch cm inch
Minimum 57.5 22 5/8 77.5 30 1/2
Maximum 70.5 27 3/4 90.5 35 5/8
Instruction Manual 3
Overhead Diagram
The KVM Module can be connected to a console, or be used as a stand-alone
KVM Switch. There are three major categories: PS/2, USB and Sun Interfaces:
Type PS/2 KVM
Model name CAB832DS CAB1631D CAB1631D1U
No. of Console Ports 2 1 1
No. of Computer Ports 8 16 16
OSD Menu Yes Yes Yes
Height 1U 2U 1U
Cable Type SVPS23N1_xx, PS23N1THINxx SVECONxx
Continued next page
KVM Module
Console
Drawer
KVM Module
Console
Drawer
Depth
Depth
Instruction Manual 4
Type Hybrid KVM
Model name CAB831HD CAB1631HD
Interface PS/2, USB
No. of Console Ports 1 1
No. of Computer Ports 8 16
OSD Menu Yes
Height 1U 2U
Cable Type PS2 – SVECONx
USB - SVECONUSx
Type IP KVM
Model name CAB1641HDI
Interface PS/2, USB
No. of Console Ports 1
No. of Computer Ports 16
OSD Menu Yes
Height 1U
Cable Type PS2 – SVECONx
USB - SVECONUSx
Instruction Manual 5
Assembly
1. Choose a proper position for the rack drawer. Mount the rear brackets (from
the Rear bracket & extension kit) and lightly fasten them onto the rear
vertical poles. Both will be removed later.
2. Remove the safety stopper from the console drawer. The safety
stopper is designed to prevent the drawer from sliding out during
transportation. Please note that once the Safety Stopper is removed,
the drawer is free to slide out when the console is tilted. Be cautious,
as this could cause injury.
Instruction Manual 6
3. Slide the assembled drawer into the rack cabinet from the front and insert
the two slide rails of the assembled drawer into the pockets of the rear
brackets.
4. Fasten the assembled drawer onto the front brackets using the four screws
provided.
5. Remove both of the rear brackets. The front brackets now hold the
assembled drawer.
Instruction Manual 7
6. Attach the extensions (from the Rear bracket & extension kit) to both
sides of the KVM switch module. Please note the length of the
extensions and mount them as shown. For a 2U module, the
extensions are mounted to the lower half of the module.
NOTE: the orientation of the wide side of the extension
7. The rear brackets, extensions and slide rails have a tight t. Make sure you
follow these steps for easy installation.
A. Slide the rear brackets onto the extensions.
B. Insert both sliding rails of the assembled drawer into the tight space
formed by the rear brackets and the extensions. The KVM module should
be pushed in evenly on both right and left sides.
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels StarTech.com Mixeur musical
