StarTech.com ST1218T Manuel utilisateur
ST1218T
VGA over Cat5 UTP Extender
- 8 Port
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital de-
vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com. Where
they occur these references are for illustrative purposes only and do not represent an endorse-
ment of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. Regardless of any direct acknowl-
edgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names and/or symbols
contained in this manual and related documents are the property of their respective holders.
Instruction Manual
i
Instruction Manual
Table of Contents
Introduction ................................................................................... 1
Features ......................................................................................1
Package Contents .......................................................................1
Product Description ...................................................................... 2
Front Panel ..................................................................................2
Rear Panel...................................................................................2
Hardware Installation .................................................................... 3
Installing the ST1218T Transmitter Unit.......................................3
Installing the ST121R Receiver Units (not included) ...................3
Driver Installation .......................................................................... 3
Cat5 Cable ...................................................................................... 4
Operation........................................................................................ 5
LED..............................................................................................5
Equalizer Selector (ST121R, ST121EXT) ...................................5
Specifications ................................................................................ 6
Troubleshooting............................................................................. 7
Technical Support ......................................................................... 8
Warranty Information .................................................................... 8
Instruction Manual
1
Introduction
Thank you for purchasing the StarTech.com ST1218T VGA over Cat5
UTP Extender - 8 Port. The Converge A/V VGA over Cat5 video extender
allows you to connect up to eight remote displays directly from one video
source. The video signal is sent to remote monitors over standard Cat5
UTP cable using RJ45 connectors and supports distances of up to 150m
(492ft). The ST1218T requires the ST121R remote receivers or the
ST121EXT repeater/extender to connect additional displays in between
the Transmitter (ST1218T) and Receiver (ST121R).
Allow Converge A/V to provide you with digital signage solutions.
Applications include airports, bus depots, retail, or any large buildings
where video needs to be delivered at long distances.
Features
Consists of 1 Base unit (Transmitter) for distributing 8 remote displays•
through Cat5 and two local VGA displays
Extends video cables by up to 492 ft. (150m)•
Provides crystal clear picture quality•
Pure hardware design, no software or drivers required and easy to•
install
Supports VGA, SVGA, and Multisync monitors•
Use repeaters along your path to connect additional displays or to•
connect directly to a remote display
Package Contents
1 x ST1218T Transmitter Unit•
1 x Universal Power Adapter•
1 x Instruction Manual•
Instruction Manual
2
Product Description
Front Panel
Rear Panel
RJ45 Output to
Receiver Units
RJ45 Output to
Receiver Units
Power
Input
VGA Input (male) VGA Output (female)
Instruction Manual
3
Hardware Installation
Installing the ST1218T Transmitter Unit
Place the Transmitter Unit near the local (source) computer.1.
Switch off the computer and disconnect any existing VGA cables.2.
If desired, connect the VGA cable from the local computer display(s) to3.
the female DE-15 VGA ports on the Transmitter Unit. This will enable
you to see video locally while an image is transmitted to the remote
display. You may choose to connect up to two local displays, one for
each “Monitor” port. Both outputs display the same image.
Connect a male-to-female DE-15 VGA cable (not provided) to the VGA4.
output on the local computer. Connect the opposite end to the VGA IN
port on the Transmitter Unit.
Connect each Cat5 cable connection to the “CAT5 OUT” ports on the5.
Transmitter Unit.
Connect the Power Adapter (provided) into an appropriate power6.
source and plug the opposite end into the power connector on the
Transmitter Unit. The POWER LED will light up.
NOTE: To prevent potential electrical damage to the unit in some
environments, ensure that the chassis is properly grounded.
Installing the ST121R Receiver Units (not included)
Connect the opposite end of the Cat5 cable from the Transmitter Unit to1.
the “CAT5 IN” port on the ST121R Receiver Units.
Adjust the Signal Equalizer switch setting to the appropriate length of2.
Cat5 cable used (see documentation included with St121R).
Connect the Power Adapter provided with the ST121R into an3.
appropriate power source and plug the opposite end into the power
connector on the ST121R Receiver Unit. The POWER LED will light up.
Driver Installation
No driver installation is required for this video extender as they are pure
hardware solutions and not visible to the computer system.
Instruction Manual
4
Cat5 Cable
The Video Extenders requires an unshielded twisted pair Cat5 cable no
longer than 150m (500ft.).
The cable must be wired according to the EIA/TIA 568B industry standard
as shown below.
NOTE: Cat5, Cat5e, or Cat6 cables can also be used with the extender
pair.
The above diagram shows the RJ45 connector of a Cat5 cable with its
metal contacts facing up.
Pin Wire Color Pair
1 White/Orange 2
2 Orange 2
3 White/Green 3
4 Blue 1
5 White/Blue 1
6 Green 3
7 White/Brown 4
8 Brown 4
Instruction Manual
5
Operation
LED
There are two LEDs on the Transmitter unit. The POWER LED will
illuminate indicating that the unit is properly powered. The ACTIVE LED
illuminates when there are VGA input signals present.
The POWER LED of the Receiver and Reapter Units also illuminates
indicating that the unit is properly powered. The ACTIVE LED illuminates
when VGA signals are properly decoded from the Cat5 for the two local
DE-15 VGA outputs.
Signal Equalizer Selector (ST121R, ST121EXT)
The Signal Equalizer Selector on the Receiver and Repeater Units
can be adjusted to obtain the optimal video signal for various cable
lengths. There are four settings on the selector switch, indicating cables
of different lengths. The following table can be used as a reference for
selecting the appropriate setting:
Cat5 Cable Length Equalizer
Position
meters feet
0 ~ 40 0 ~ 131
40 ~ 80 131 ~ 262
80 ~ 120 262 ~ 394
120 ~ 150 394 ~ 500
Instruction Manual
6
Specications
Connectors
1 x DE-15 VGA male (input)
2 x DE-15 VGA female (output)
8 x RJ45 female
1 x Power connector
LEDs 1 x Power
1 x Active
Maximum Distance 150 m (492 ft) @ 1024x768
Maximum Video Resolution 1600x1200 @ 50 m (150 ft)
Power Adapter 9~12VDC, 1.5A
Dimensions 180.0mm x 85.0mm 20.0mm
Weight 1300 g
Instruction Manual
7
Troubleshooting
Symptom Solution
No VGA signals at the Reeceiver
unit
Both units must be powered.
The ACTIVE LED on the Transmitter
unit and the Receiver unit must
illuminate to indicate the proper
transmission of the signal.
VGA signal is garbled Ensure that the cables being used
are wired according to the EIA568B
standard.
ACTIVE LED at the Receiver unit is
always off.
The ACTIVE LED on the Transmitter
unit must be on. Check the wiring of
the Cat5 cable.
Ensure that the POWER LED of the
Remote unit is on.
VGA quality changes with the use of
different Cat5 Cables.
Use the equalizer selector to adjust
the VGA signal for various cable
lengths and characteristics.
Table des matières
Autres manuels StarTech.com Extenseur
StarTech.com
StarTech.com ST121HDBT20L Manuel utilisateur
StarTech.com
StarTech.com USBthere USB221EXT Manuel utilisateur
StarTech.com
StarTech.com 410VDSLEXT Manuel utilisateur
StarTech.com
StarTech.com ST121WHDS Manuel utilisateur
StarTech.com
StarTech.com USBthere USB204EXTFIB Manuel utilisateur
StarTech.com
StarTech.com ST12MHDLANU Manuel utilisateur
StarTech.com
StarTech.com SV565UTP Manuel utilisateur
StarTech.com
StarTech.com ST12MHDLNHR Manuel utilisateur
StarTech.com
StarTech.com SV565FXHD4KU Manuel utilisateur
StarTech.com
StarTech.com HDBOOST4K Manuel utilisateur
StarTech.com
StarTech.com DVIAEXT10 Manuel
StarTech.com
StarTech.com ST121R Manuel utilisateur
StarTech.com
StarTech.com PS2UTPEXT Manuel utilisateur
StarTech.com
StarTech.com DPBOOST Manuel utilisateur
StarTech.com
StarTech.com IPUSB2HD3 Manuel utilisateur
StarTech.com
StarTech.com 110VDSLEXT2 Manuel utilisateur
StarTech.com
StarTech.com ST1214T Manuel utilisateur
StarTech.com
StarTech.com USBthere USB204EXTFIB Manuel utilisateur
StarTech.com
StarTech.com SV565UTPDUA Manuel utilisateur
StarTech.com
StarTech.com ST121HDBTU Manuel utilisateur
