Starling Technologies S-HAL-9 Manuel utilisateur
www.starling-tech.com
Instruction Manual
Warning : Protect Board from electrostatic discharge. Ground yourself before handling.
Protect bottom of board from shorting against anything metal.
Thank you for purchasing the P-N-P H.A.L light and sound kit
from Starling Technologies™.
We are excited to release our light and sound kit for the infamous
computer from the mo ie "2001: A Space Odyssey."
Features red glowing eye and 30 phrases with extremely high quality life like
sound acti ated by a motion sensor.
Volume is adjustable by small blue trim-pot.
Kit is completely assembled, all you do is add batteries and turn on the switch.
Note: after 30sec of non-acti ation of the sound card, the sound will start o er
from the beginning of the phrases when next acti ated.
Included in kit:
1x The H.A.L high quality sound efx board acti ated by motion sensor.
1x on/off slide switch
1x 3x AAA battery holder.
No soldering required.
equired:
Hot-glue
Model Master clear parts cement & window maker or equi alent.
Drill bits
1
Startup:
After adding batteries, turn the unit on. HAL will greet you with “Good E ening
Da e”. He may also acti ate another sound at this time, as the motion sensor is
analyzing its en ironment, which is normal.
Mo ing your hand past the sensor or walking past it will set off another
phrase. If left inacti e for 30sec, the sound will start o er from the beginning of
the phrases when next acti ated.
2
Very simple install of the kit.
Hot-glue can be used to install e erything but the lenses.
Looking at the soundboard, next to the battery holder below, there is a blue
square trim pot. Turn the screw clock-wise to increase olume, turn counter
clock-wise to reduce olume.
Hal speaker and motion sensor without dome lens.
3
This was my choice for the motion sensor installation. I discarded the dome
lens so that I could hide the sensor. I drilled all holes in the speaker area of HAL.
Placing the sensor behind one of the holes ga e me a motion range of about 4ft.
I enlarged one of the holes, shown abo e, gi ing a range of about 10ft. E en
though this hole is larger, when looking at the front of HAL, this hole still blends
in.
This installation limited the annoying acti ation of e ery mo ement in my
office, gi ing me more control of when HAL acti ates. You may also choose to
install the sensor outside the model to use it with the dome if you need more
sensiti ity.
Line up the motion sensor chip, the round protrusion with rectangular
window, centered o er the large hole you drilled. Hot glue it in place. Make sure
the sensor is mounted flat, not angled in one direction or else the sensor will be
more sensiti e to one side than the other. Mine is a bit off but I don't mind it :)
Test the sensiti ity, if it works well for you, add a little more hot-glue.
4
I hot glued it on 3 edges. While your at it, glue the speaker in place as well as
the switch. Looking at the first photo in this manual, hot-glue the soundboard
and the 3xAAA battery holder as shown. If the red eye LED is loose, use a little
hot-glue around the edges to hold it in place.
Here is my completed model of the HAL9000. Lea e it on its stand or do as I and
hang him on the wall. Enjoy the life like sound coming from your ery own
HAL :)
5
Paints used for this build:
Rust-Oleum American Accents 2x Paint&Primer Flat black
Tamiya AS-12 Bare-Metal-Sil er.
Specifications
Board supported voltage: 4.5 olts supplied by 3x AAA batteries.
Troubleshooting
When the batteries begin to degrade, phrases may play incomplete, or distance
from motion detection will decrease. The LED red eye will remain bright.
This is normal and it is time to change the batteries.
All photos contained in this document are property of Starling technologies. This document may not be
copied, sold or transfered without permission.
E/FX™ is a trade mark of Starling Technologies™
Copyright © 2022 Starling Technologies™ www.starling-tech.com
6
Table des matières
Autres manuels Starling Technologies Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
