Version 2.17.4
S9 V2
1. Disarm security system.
2. Switch ignition O, if it is On, then press service button 7 times.
3. Switch ignition On.
4. 7 LED ashes of service button and 7 buzzer sounds will follow.
5. Then 2 LED ashes of service button and 2 buzzer sound signals will follow, conrming entry into Registration mode.
6. Enter the owner authorization code using car OEM buttons with a pressing interval no more than 3 seconds. Every button
pressing should be followed by a single service button LED ash.
The owner authorization code consists of a code sequence containing from 3 to 30 OEM buttons pressing. The list of supported
OEM buttons is available at can.starline.ru. If a service button LED ash does not follow after pressing of OEM button, so this
button is not supported for this car.
7. In 3 seconds after the code entry 2 short LED ashes and 2 buzzer sound will follow, conrming the code successful registration.
8. Enter the owner authorization code again.
9. If the code is recorded properly, 2 LED ashes and 2 short buzzer sound will conrm. If the code recording is failed, so 4 short
buzzer sounds will follow, in this case repeat steps 6-8.
10. In 10 sec switch ignition O to exit the Registration mode.
11. An exit from Registration mode will be conrmed by double LED ashes and buzzer sounds and then additional signals in
amount of total registered tags, pagers and smartphones will follow.
12. Write down and memorize this push sequence.
Switch to device registration mode
1. Disarm the security system.
2. Switch ignition O if it is On.
3. Press the service button 7 times.
4. Switch ignition On. 7 light LED ashes of service button and 7 buzzer sounds will follow.
5. 2 short LED ashes and buzzer sounds will conrm entry into the Registration mode.
2-way remote control (pager) registration
6. Press a pager buttons 1 and 2 shortly.
7. In 3 seconds successful registration will be conrmed by a short beep sound of a pager, 2 LED ashes of service button and 2
buzzer sound signals. If pager is not registered, 4 beep sounds of pager will follow.
8. Repeat points 6-7 for each pager.
Bluetooth tags (transponders) registration
9. Remove a battery from tag.
10. Hold a tag button pressed and insert a battery back. A tag LED will turn red.
11. Release a button, a series of red ashes will follow.
12. In 10 seconds successful registration will be conrmed by a green LED ash, 2 ashes of a service button LED and 2 buzzer
sounds. If a tag is not registered LED will turn red.
13. Repeat points 9-12 for all the remaining tags.
Smartphone registration
14. Register a smartphone* with use of the free StarLine mobile App.
Exit from the device registration mode
15. In 10 seconds switch ignition O to exit the registration mode. An exit from Registration mode will be conrmed by double LED
ashes and buzzer sounds and then additional signals in amount of total registered tags, pagers and smartphones will follow.
* The iOS and Android smartphone with Bluetooth Smart 4.2 and above are supported.
Programming an owner authorization code (with car buttons)
New devices registration
NOTE! At registration of new tags and smartphones all previously registered tags and smartphones will be erased from
memory. So the existing devices should be registered simultaneously in one cycle with all the new devices. In total up to 5
Bluetooth devices can be registered in the system main unit.
When new RF pagers are registered, all previously registered remote keys will be erased from memory. So the existing
remote keys should be registered simultaneously in one cycle with all the new remote keys.
In total, up to 4 RF pagers can be registered in the system main unit.
NOTE!The tags included in the delivery set are already registered in the main unit and are in the transport mode,
i.e. o. Pressing the tag button in this mode will be indicated by a green and red ashes of the built-in LED. Prior to
operation press the tag button several times until the LED color turn to green (regular mode).
Power module V1
Power module V2
+ 12 V
30 A + 12 V
+ 12 V
START
STOP
E
N
G
I
N
E
blue
black-yellow
red
10-50 kOhm
+12 V
blue-white Heater
control unit
pink
10-15 kOhm
+12 V
51-75 kOhm
Heater
control unit
pink
gray-black
blue-white
blue
+ 12 V
30 A
blue
red
black-yellow
or
Brake trigger switch
Brake trigger switch
Brake lights lamp
Brake lights lamp
Push-to-Start
button
To the blue wire
of connector Х2
To the blue wire
of connector Х2
To the red wire
of connector Х2
To the red wire
of connector Х2
To the black-yellow
wire of connector X2
To the black-yellow
wire of connector X2
Negative control pulse
1.
In StarLine Master program set X2:6 blue wire as "Engine start: simulate brake or clutch pedal" and X2:14 black-yellow wire
as "Engine start: PTS button".
2.
Connect wires according to diagram for corresponding power module.
Diagram of start circuits connection on vehicles with PTS button
Webasto heater connection with digital bus control
1. In StarLine Master software set the pink
output wire of X1 connector as “Webasto
heater control via digital bus”, the gray-black
wire – as “Webasto preheater start control via
digital bus".
2. In “Engine start” section “Starting preheater”
enable “Permission for preheater operation”.
For the point “Start type of preheater” select
option “Webasto via digital bus”.
3. Connect the wires according to the diagram.
yellow
Eberspächer heater connection with digital bus control
1. In StarLine Master program set the pink
output wire of X1 connector as “Eberspacher
preheater control via digital bus”
2. In “Engine start” section “Starting preheater”
enable “Permission for preheater operation”.
For the point “Start type of preheater” select
option “Eberspacher via digital bus”.
3. Connect the wires according to the diagram.
Additional connection options
Conguring the security-telematic system
