Star TCP300 SERIES Manuel utilisateur
THERMAL RE-WRITABLE
CARD READER / WRITER
TCP300 SERIES
•
User’s Manual
•
This ‘User’s Manual’ describes important information to enable you to use
the reader/writer safely.
Carefully read this manual before using the reader/writer and observe the
descriptions herein.
CARD SYSTEM SALES SECTION OVERSEAS SUBSIDIARY COMPANIES
STAR MICRONICS CO., LTD. STAR MICRONICS AMERICA, INC.
536 Shimizuanatsushinnya, Shizuoka, 1150KingGeorgesPostRoad,Edison,NJ08837-3729U.S.A.
424-0066 Japan Tel: 732-623-5555, Fax: 732-623-5590
Tel: 0543-47-0122, Fax: 0543-48-5013 http://www.starmicronics.com
STAR MICRONICS U.K. LTD.
Please access the following URL Star House, Peregrine Business Park, Gomm Road,
http://www.star-micronics.co.jp/service/ High Wycombe, Bucks, HP13 7DL, U.K.
frame_sp_car_e.htm Tel: 01494-471111, Fax: 01494-473333
for the lastest revision of the manual. http://www.starmicronics.co.uk
2003.09.01
Printed in Japan, 59082065
TABLE OF CONTENTS
1. recautions for Safe Use ........................................................ 1
2. General Description ................................................................ 4
3. Unpacking ............................................................................... 5
4. External Appearance and art Names .................................... 6
5. Connect to and Setting External Devices ................................ 7
6. Interface Board Replacement (RS-232C to USB) ................. 10
7. Cleaning Cards...................................................................... 11
8. Troubleshooting ..................................................................... 12
9. General Specifications .......................................................... 14
– 1 –
1. Precautions for Safe Use
Carefully read and obey the following items to prevent injury to yourself or to others
and to prevent damaging property.
Precautions for Reader/Writer Setup
1. Setup the reader/writer in a solid, and level location. Do not physically jar or shake
the reader/writer.
This can damage it or lead to injury.
2. lace the reader/writer in a location out of the reach of children.
Allowing children to touch the reader/writer can lead to injury.
3. Do not use or place the reader/writer in areas exposed to direct sunlight, or in high
temperatures areas such as next to fire or electric or kerosene heaters.
Exposing the reader/writer to excessive heat will cause it to become hot and break-
down, mis-operate or become burned.
4. Avoid using or storing the reader/writer in locations where liquids such as water or oils
can enter the internal reader/writer mechanisms, or in areas of high humidity.
Exposing the reader/writer to excessive moisture will cause it to become hot and can
cause electric shock, mis-operate or reader/writer failure.
5. Avoid using or storing the reader/writer in locations where dust or metallic powder can
enter the internal reader/writer mechanisms.
Exposing the reader/writer to excessive dust will cause it to become hot and can
cause electric shock, mis-operate or reader/writer failure.
6. Avoid using the reader/writer in locations where corrosive gases, ignition gases, chemi-
cals or vapors are emitted.
Exposing the reader/writer to vapors will cause it to become hot, burn, cause electric
shock, or cause reader/writer failure.
7. Avoid using near objects that emit a magnetic field.
Magnetic fields can erase the information recorded on cards.
8. Use the appropriate power conditions for the TC 300 series.
The wrong type of power will cause the reader/writer to become hot and can cause
mis-operate or reader/writer failure.
9. Use an outlet that can easily be connected to and disconnected from.
10. Do not get power from a circuit to which electrical devices that generate electrical
noise are connected.
Using the same circuit can cause the reader/writer to mis-operate or can cause reader/
writer failure.
11. Allow plenty of space around the reader/writer for ventilation of heat and operation.
Not enough space will cause the reader/writer to become hot and can cause mis-
operate or reader/writer failure.
Always bserve the f ll wing items.
– 2 –
12. Do not store the accessory cleaning liquid in a location that is exposed to direct sun-
light or near heat generating devices.
Storing near heat can cause fires.
13. Do not allow the accessory cleaning liquid to get in your eyes and do not drink it.
Drinking the liquid can cause health problems.
14. Do not store the accessory cleaning liquid in a location where children have access to it.
Drinking the liquid can cause health problems in children.
Precautions for Reader/Writer Use
1. Use only Star recommended cards.
The reader/writer and the card may not operate normally if other cards are used.
2. Do not use cards that are dirty or oily or wet in any other manner. Also, do not handle
cards with dirty or wet hands. Do not apply tape or glue to cards.
The reader/writer will not operate normally.
* If a card is dirty, clean the card and the reader/writer.
See section 7. Cleaning Cards for details on how to clean.
3. Do not store cards near devices that generate magnetic fields (such as cellular tele-
phones, speakers, televisions, etc.) or approach magnets toward them.
Magnetic fields can erase the information recorded on cards.
4. Do not store cards in high temperature areas (such as dashboards in automobiles).
Storing in high temperature areas can cause cards to bend or it can erase the infor-
mation recorded on cards.
5. Do not used bent cards.
Using bent cards can cause them to become jammed.
6. Insert cards in the indicated direction.
Inserting them incorrectly can cause mis-operation or it can erase the information
recorded on cards.
7. Absolutely never insert anything other than cards into the reader/writer.
Inserting other objects can cause the reader/writer failure or electrical shock.
8. Do not obstruct the inserting or discharging of cards.
Obstructing can cause the reader/writer failure, mis-operation or injury.
[TC 300]
(Figure for Reference)
– 3 –
9. Do not cut the power while a card is being processed.
Cutting the power can erase the information recorded on cards.
10. In case of reader/writer error (abnormal sounds, abnormal odors, smoke, fire) turn off
the reader/writer immediately and unplug it from the power outlet.
Continuing use under such errors will cause the reader/writer failure or burns. Re-
quest repairs from the sales outlet.
11. Always hold the plug to unplug the power cord from its outlet. ulling on the cord will
damage the cord. Do not pull on the cord. Do not place heavy objects on the power
cord. Do not use power cords that are damaged or deformed. Consult with your
sales outlet.
12. When discontinuing use for prolonged periods, always remove the power plug from
the outlet.
13. Avoid sudden changes in environment, such as changes in ambient temperature and
humidity.
Sudden changes can cause condensation and mis-operation. Allow the reader/writer
to sit in its new environment for at least one hour before use in the event there has
been a sudden change.
14. Do not use the reader/writer in an environment where condensation has formed.
Using the reader/writer in such an environment can cause the reader/writer to mis-
operate, electrical shocks or it can cause reader/writer failure.
15. To ensure reader/writer reliability, clean the reader/writer everyday, or when the cleaning
lamp has lit.
Continuing use without cleaning will cause the reader/writer errors. See section 7.
Cleaning Cards for details on how to clean.
16. Do not disassemble or modify the reader/writer.
Disassembling or modifying the reader/writer can cause the reader/writer to mis-op-
erate, reader/writer failure or injury. If the reader/writer mis-operates, or appears to
need repair, contact your sales outlet.
17. Do not expose cards to direct sunlight or fluorescent lights for extended periods of
time.
Exposure to bright light will discolor cards.
18. When the print has faded:
Magnetically encoded information still remains on the card even when the print has
faded due to high temperatures. The card may be reprinted.
19. When cards are excessively dirty:
If cards are dirty or oily, problems can easily occur in reading and writing or cause
missing print and incomplete erasing of information.
* In such cases, clean the card and the reader/writer.
See section 7. Cleaning Cards for details on how to clean.
20. To use repeatedly:
To repeatedly print to the same card, allow for at least three minutes between prints.
When printing repeatedly to different cards, no wait is required.
– 4 –
2. General Description
The TC 300 series reader/writers are equipped with a thermal type display mechanism
on a ET magnetic strip card reader/writer. They are connected to electrical devices
such as OS and are used to print/erase characters and images freely onto the surface of
cards.
• Main Features f the TPC300 Series Reader/writer
1. Reads/writes card magnetic stripe data
2. rints/deletes the card display area
3. RS-232C and USB interface
4. Card can be reused between approximately 200 to 500 times under normal operating
conditions.
* Actual number of uses varies greatly according to type of card and environment.
– 5 –
3. Unpacking
The following outlines the reader/writer and its accessories.
The reader/writer (TC 300 Series)
1. TC 300 reader/writer
2. Cleaning cards (2 cards)
3. Cleaning fluid
4. This manual
5. Ferrite core
24
3
5
1
– 6 –
4. External Appearance and Part Names
The reader/writer (TC 300 Series)
1. ower Switch ............................ This turns the power to the reader/writer on and off.
2. ower Indicator Lamp .............. Indicates that reader/writer power is on.
3. Status Indicators ....................... Indicates printing ready, printing and errors.
4. Cleaning Lamp ......................... Indicates the reader/writer needs cleaning.
5. Interface Connector .................. Connects to host computer via a cable.
6. AC Cable .................................. Connects to power source.
7. Cleaning Switch ........................ ress the cleaning switch while turning the power on.
Insert a cleaning card dampened with alcohol to
6
1
5
4
3
7
2
– 7 –
clean the reader/writer.
5. Connect to and Setting External Devices
5-1 RS-232C Interface
<M unting the RS-232C Interface Cable>
1. Cut the power to the host computer and reader/writer.
2. Connect one end of the interface cable to the reader/writer and the other end to the
host computer.
3. Mount the accessory ferrite core to the interface cable.
4. Tighten the left and right screws on the connector.
<RS-232C Serial Interface Cable>
1 Connectors D-Sub 9 IN (Male) * Reader/Writer Side
2 Compatible Connectors D-Sub 9 IN (Female) * Cable Side
3 Connector ins See Table Below
4. I/O Circuit See Table Below
5. Level RS-232C
6. Cable Cross (Reverse) Cable
Pin N . Signal Name I/O Functi ns
1NC
-
Not Connected
2 RXD Input Reception Data
3 XD Output Transmission Data
4 DTR Output Data Terminal Ready
5 GND
-
Ground for Signal
6 DSR Input Data Set Ready (Not Detected)
7 RTS Output Transmission Request
8 CTS Input Transmission Ready (Not Detected)
9NC
-
Not Connected
– 8 –
<Settings f r C mmunicati n Speed>
To change the serial communication settings, change the following DI switch settings.
(Ex-factory Default Settings: DSW 1 to 6 are ON, 7 and 8 are OFF.)
Switches ON OFF
DSW 1-1 Baud Rate Setting (See table below)
DSW 1-2
DSW 1-3 8 bit 7 bit
DSW 1-4 arity Disabled arity Enabled
DSW 1-5 Odd arity Even arity
DSW 1-6 Fixed at On
DSW 1-7 Fixed at Off
DSW 1-8 Fixed at Off
Baud Rates BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS
DSW 1-1 OFF ON ON OFF
DSW 1-2 ON ON OFF OFF
* Mistaken DI switch settings will cause the reader/writer to mis-operate or reader/
writer failure. Be careful when making setting changes.
To change the DI switch settings, do the following.
1. Check that the power is turned off for both the reader/writer and the host computer.
2. Remove the two screws.
3. ull out the serial interface card to remove it.
4. Change the DI switch settings on the serial interface card.
5. ush in the serial interface card to mount it.
6. Tighten the two screws.
7. Turn on the power for both the reader/writer and the host computer.
N te: The new settings will take effect when the reader/writer p wer is turned back n.
DI Switches
Table des matières
Autres manuels Star Lecteur de cartes
