Stanley 204018 Manuel utilisateur
Filename: “Panic Hardware Exit Device Installation”
Location: Date Created: 8/16/2004
Issued By: PCN 04-132 Date Revised: 12/3/2004
Revised By: M. Sheehan Page 1 of 6
Panic Hardware Exit Device
Installation Manual
Quick-Reference Guide
204018
Rev. A, 12-3-04
Prohibition on Copying
Any unauthorized reproduction, disclosure or distribution of copies by any person
of any portion of this work may be a violation of copyright law of the United
States of America and other countries, could result in the awarding of statutory
damages of up to $250,000 (17 USC 504) for infringement, and may result in
further civil and criminal penalties. All rights reserved.
Stanley Access Technologies
Quick-Reference Guide
Filename: “Panic Hardware Exit Device Installation”
Location: Date Created: 8/16/2004
Issued By: PCN 04-132 Date Revised: 12/3/2004
Revised By: M. Sheehan Page 2 of 6
1. Lay SX panel horizontally with escutcheon and cylinder lock facing
down.
2. Install screw #6-32 x 2” into the center block to aid in pulling and
holding the center block in position.
3. Remove Dummy Plate from center block. Be sure to save the two #10-
32 x 3/4” flat head machine screws holding Dummy Plate, as you will
need them for later installation.
4. Locate the center block in the rectangular hole.
5. Align the protruding square of the center block with the square hole in
the mounting plate and place onto the center block. (See Fig. 5.)
6. Place scissor cartridge on center block and secure with the two #10-32
x 3/4” flat head machine screws. (See Fig. 6)
Filename: “Panic Hardware Exit Device Installation”
Location: Date Created: 8/16/2004
Issued By: PCN 04-132 Date Revised: 12/3/2004
Revised By: M. Sheehan Page 3 of 6
7. Secure Crank arm.
a. Remove the #6-32 x 2” helper screw.
b. Align crank arm with shaft. You may have to operate the push
bar scissors to align tab with slot.
c. Secure with one #6-32 x 1/4” truss head. (See Fig. 7)
8. Insert push bar (See Fig. 9) and secure end caps with four #10-32 x
1/2” self-tapping screws. (See Fig. 10)
9. Center Panic bar assembly on mutton bar. Measure six inches down
from end of panic bar. (End opposite to center block) Drill .218” hole
centered through panic hardware and mutton bar. Secure hardware
down with ¼-20 x 1” self-tapping hex head bolt.
Filename: “Panic Hardware Exit Device Installation”
Location: Date Created: 8/16/2004
Issued By: PCN 04-132 Date Revised: 12/3/2004
Revised By: M. Sheehan Page 4 of 6
10.Insert cover strip into back bar. Push in until flush with back bar
extension. (See Fig. 11)
11.Install base caps and secure with four #10-32 x 2” self-tapping screws.
(See Fig.12)
Filename: “Panic Hardware Exit Device Installation”
Location: Date Created: 8/16/2004
Issued By: PCN 04-132 Date Revised: 12/3/2004
Revised By: M. Sheehan Page 5 of 6
12.Adjust bottom throw bolt length.
a. Remove the four #10-32 flat head screws from the guide block in
the bottom of the stile
b. Rotate the bottom throw bolt counterclockwise until it sticks out
5/8” from the bottom of the stile.
c. Replace guide block and four #10-32 flat head screws.
13.Check operations.
a. Fully depress push bar and release
b. Top bolt will retract and latch.
BOTTOM
THROW
BOLT
GUIDE
BLOCK
MOUNTING
SCREWS
Filename: “Panic Hardware Exit Device Installation”
Location: Date Created: 8/16/2004
Issued By: PCN 04-132 Date Revised: 12/3/2004
Revised By: M. Sheehan Page 6 of 6
c. Push the jamb sensor in and you should see about 5/8” of
movement from the top bolt.
Table des matières
Autres manuels Stanley Outils
Stanley
Stanley Kit 6 Manuel utilisateur
Stanley
Stanley 160173XSTN Manuel utilisateur
Stanley
Stanley SST1801 Manuel utilisateur
Stanley
Stanley 55 Manuel utilisateur
Stanley
Stanley BXGT10147E Instructions d'installation et d'utilisation
Stanley
Stanley SPL31A-N Manuel utilisateur
Stanley
Stanley DR19 Manuel utilisateur
Stanley
Stanley BR87 Manuel utilisateur
Stanley
Stanley CH15 Manuel utilisateur
Stanley
Stanley AV50 Guide de dépannage
Stanley
Stanley SFP 1250 Manuel utilisateur
Stanley
Stanley GD50 Manuel utilisateur
Stanley
Stanley MB2140-E Manuel d'instructions
Stanley
Stanley STXH2000 Manuel utilisateur
Stanley
Stanley CH18 Manuel utilisateur
Stanley
Stanley CH1513101 Manuel utilisateur
Stanley
Stanley 150 Manuel utilisateur
Stanley
Stanley HSX Series Manuel utilisateur
Stanley
Stanley S32 Manuel utilisateur
Stanley
Stanley BR Series Manuel utilisateur
