R'
--i
• 1
SB
[
__
RE
_,]
~
p
PH
PA
SA
(Deceleration closing) =this is the deceleration distance on the total race in the closing phase,
O= min ; 1 =maximum.
(Beat Space) =thls is.the space needed tor the central unit to recognize the beats , 0=
low
, 1 =
max . This feature results in a greater
or
lesser precision in the approach to
tile
beats.
(Relax) =if this function is enabled, for a few hundredths
of
a second. allowing the motor to turn
in the opposite direction to the just ended movement. In this way, it avoids the unlocked problems,
this feature can
be
used on assigned barriers.
(output relay) =
Auxiliary relay operation
=o
:the dry contact output switches with
open
bar;
=1
: working as second radio channel rf 2 . storing a button on
"2
eh
••
while pressing the button,
the
dry
contact relay output energizes tor 1
s.
=2:
activates the opening relay tor
1s
( for electric lock
).
(Operation light sensor) = .
Default :
O.
The light sensor is not active and the lights outputs RED and GREEN operate uninter-
ruptedly according to the logic expected : stopped
bar
-flashing RED light, opening bar -steady
RED light. open bar- flashing GREEN light, closing bar , continuously fix.ed RED lit.
1: the lights are activated as above only if the sensor detects darkness (fixed threshold for now
„.
)
(Working photocell input in closing) =(Behavior Closing photocell input ) =
O: occupying the photocell beam, the bar stops and starts.
1 : occupying the photocell
beam
, the bar stops and once the beam released, it closes.
(Working photocell input in opening and closing)
O: occupying the photocell beam , the bar stops and starts again
if
in closing, if in opening would
stop and
once
released the beam , would continue the opening .
1 : occupying the photocell beam , the
bar
stops and opens again
if
in closing, if in opening would
ignore the beam interruption.
(Remote controls at fixed cede)= ( Fixed cede ) =
lf
actlvated, the control panel is enabled tor
storing remote controls on Cede Fixed
of
type HT53200, and on fixed Rollingcode HCS.
(Fire allann on the STOP command) (Stop -Fire Alarm) =defines the STOP input behavior. you
can choose from :
O: STOP NC contact , each tirne it is opened , the panel will
show"
ALAR " and it will stop imme-
diately.
To
let it continue just make a
new
START pulse.
1 : FIRE ALARM , NC contact • each tirne you open the barrier
it
opens, it
the
contact
is
main-
tained opened , it will ignore all incoming commands.
To
make it close you will simply close the
contact and give a
new
impulse
to
.START . For situations involving the Antifire.
Detault: O
011
: 0
On: 1
Default: o
Off:O
On: 1
Default: O
011:0
On: 1
Detault: 1
Default: O
Default: O
011:0
On: 1
Default: O
011:0
On: 1
Default: o
011:
o
On: 1
Default: O
~
WARNING : BAand BP are useful In cases wbere there are severa! steps with different input through
the
same entrance.
DESCRIPTION "DELETE" MENU
The Reset menu item DELETE serves to restore to default all the parameters and
functions.
Once entering
in
DELETE
menu, move to the item RESET, pressing ENTER the display will start flashing to be confirmed , re-press ENTER if you
want to reset to factory
de
fault . Otherwise
qu
it .
lf
you press Enter on the display, It will read PAG indicating the reset in
progress.
To
delete a remote control from the Skygates Central Unit is essential
to
have the rernote control. and when accessed to
the item "DELETE
TX
1" press the button on the transmitter to
be
deleted.
lf
this button is not found the Central will return
"ERA". instead.
it
it is found and then eliminated, you will see "OK" in the display.
This item gives the option to delete all remote controls from the memory, either on channel 1 and channel 2.
ACCESSORIES DIAGNOSTIC DESCRIPTION
The
control center is able
to
recognize problems
or
alarms that
may
occur on the system, so
it
may
report on the main display some messages
to allow the detection
of
the problem:
• 1
RF
=activation
o!
the START command on the first radio frequency
channel, with transmitter.
• 2
RF
=activation
of
the second radio frequency channel, with the
transmitter.
•
1s
=activation
of
the START on the input
of
the clarnp.
•
srn
=activation of the STOP on the input
of
the clamp.
•
PHO
= activation of the entrance
of
the closing photocells on clarnp.
•
PHO
Rc input activation
of
the photocells during opening and Closing
tile
clamp.
•
R:'lP
=action
ot
the amperornetric sensor on the first motor.
•
ENC
= Action o!the encoder sensor on the first motor.
•
OPE
=open button active on the clamp.
• C
LO
=close button active on the clamp.
• IBRT= low
battery.
voltage lower then
21V
•
PRG
= programming of settings or functions in progress
•
OK
= successful operation.
•
ERR
= failure operation.
•
FUL
L= full rernote controls memory.
•
ATTE
N
DI
=wait, pause.
•
ro
ur
=waiting tirne expired.
„ www.stagnoli.com
ali e e in ormaz1oni"qui contenute sono
da
rifencrsi suscettib'iti
~
lica
m qua
sias1
momente c a nostro 1nsinda
Ccib
ile
gru
·
~liz
10
Ali
dotos
ond
information contoincd therein must
be
regarded
lo
chonge
at
ony
tirne
ond
on
Our
discretion.
