L
N
MAIN
POWER SUPPLY
FUSE
500mA
C
CP
L N
120-230V
50-60Hz
1 2 3 4 5 6 7 8
DRY
11. RESET
üSwitch off power supply to the module
üConnect as show in figure
üSwitch ON power supply and wait 30 seconds until the
motor makes 2 alternating movements, to indicate that
factory conditions are restored.
üSwitch off power supply to the module
üRestore the connections (see section 02. ELECTRICAL
CONNECTIONS)
üFollow the instruction at section 03. FIRST
INSTALLATION
11B. RESET USING THE BUTTON INPUT
With this procedure you can store / delete others transmitters in addition to the first already stored, or store
/ delete wind sensor or a sun/wind sensor or store / delete a rain sensor.
NOTES:
üThe module can store up to 15 radio codes (excluding sensors, wind or sun / wind radio). The "out of
memory" condition is indicated with two downward movements.
üIf the motor has stored a single hand-held transmitter, it can't be deleted (the non-cancellation is
indicated by two downward movements).
üThe module can store up to 4 wind radio sensor, one of which may be a sun sensor / wind. The "out
of memory" condition is indicated with two downward movements.
üThe module can store more rain sensors.
(1) If the sensor is a battery sensor button 1 must be pressed up to 10 seconds.
Bring the motor to an
intermediate position
A
The motor signals the operation performed
MEMORIZED ! DELETED !
E
Press for 5 seconds the
PROG button of a transmitter
already memorized.
B
The motor makes 2 upward
movements
C
WIND SENSOR
(1)
RAIN SENSOR
P2
(1)
(1)
Hand-held TRANSMITTER
DWITHIN 15 SECONDS PRESS:
(1)
STOP P1 P2
x2
x1 x1
04. MEMORIZATION / DELETION OF A RADIO DEVICE
If a wind radio sensor measures that the wind speed is above the threshold set on the sensor, the wind
sensor sends the message of "wind alarm": the modules tuned to it makes an upward manoeuvre and
commands are inhibited as long as it remains the dangerous situation.
As soon as in the module is stored a wind sensor is automatically activated control of communication
between the wind sensor and the module. If communication is lost for more than 60 minutes, the module
performs an upward movement for the protection of the roller. This manoeuvre is performed automatically
every 60 minutes until the restoration of radio communication. The factory recommends keeping the
"radio test" in order to identify in good time any malfunction of the radio sensor. With the following
procedure you can enable or disable the "radio test":
05. OPERATING LOGIC OF WIND SENSOR
05.1 TEST RADIO FUNCTION
If the sun sensor measures a brightness above the threshold set for at least 2.5 minutes, sends the
message "sun" and modules, tuned to it, command a downward movement. If the sun sensor measures a
brightness below the threshold set for at least 18 minutes, sends the message of "no sun" and modules
594REN00, tuned to it, command an upward movement.
The "sun function" can be activated / deactivated from the transmitter (see transmitter manual under "sun
function"). If the "sun function" is deactive, 594REN00 ignores the commands about the sun sent from the
radio sensor.
06. OPERATING LOGIC OF SUN SENSOR
If the rain sensor measures a rain intensity exceeds the threshold set on the sensor, the rain sensor sends
the message "rain" and modules 594REN00, tuned to it, performs an upward or downward manoeuvre,
according to how is set the rain sensor. The manual controls are still active. More rain sensors can be
stored in the same 594REN00.
07. OPERATING LOGIC OF RAIN SENSOR
Is the closure time of the relays when a manoeuvre is commanded . The factory sets the "working time" to
120 sec.
08. WORKING TIME
NOTES:
Motor signals the current «working time».
Example: if «working time» is 120 s, motor signal is:
1 briefly movement = 1 Pause - 2 briefly movements= 2 Pause - 1 large movement = 0
If you try to set «Working time» lower than 5s or greater than 240s, the value is rejected and the motor
makes 2 short movements down
N° of movements
Duration of orientation movement
1
inactive
2
50 msec
3
100 msec
4
150 msec
5
200 msec
This feature can be useful, for example in the handling of sun protection. If the function is activated, the
RIGHT and LEFT function of the 594 transmitters will command short movements which will allow easy
orientation of the sun protection. With 593 trasmitter you must press briefly twice STOP than press UP or
DOWN. The command can also be given by any buttons connected to the module; to use the function,
press a button (less than 0.5 sec), then press it again and hold it until you reach the desired orientation.
The factory sets the function to inactive.
09. ORIENTATION FUNCTION
NOTE:
üIf you try to set «Orientation time» greater than level 5, the value is rejected and the motor makes 2
short movements down.
üIf you want to stop the procedure, press briefly the MENU button of transmitter.
üWhen «Orientation time» is set on level 1 (inactive), if you command the orientation movements by
transmitter or by command buttons, the motor will not move.
N° of movements
AIR CHANGE
1
inactive
2
2 sec
3
3 sec
4
4 sec
5
5 sec
6
6 sec
This feature is especially useful if you want to identify a preferred position of the roller blind. Recalling the
intermediate limit switch function by a stored portable transmitter, a complete operation of descent is
carried out and, elapsed the work time, an upward movement is carried out whose duration can be set via
this parameter.
10. “AIR CHANGE“ FUNCTION
NOTES:
üIf you try to set «Air change» greater than level 6, the value is rejected and the motor makes 2 short
movements down.
üWhen «Air change» is set on level 1 (inactive), if you recall the intermediate limit switch by transmitter,
the motor will not move.
11A. RESET USING A MEMORIZED TRANSMITTER
This procedure restores the receiver to the default conditions (factory settings). This
procedure must only be carried out by qualified technical staff. Having carried out the reset
procedure, the qualified technician must promptly carry out all the installation operations
described at section 03. FIRST INSTALLATION
üSelect, on the transmitter, the radio channel that controls the device you want to reset.
üMake sure that this radio channel controls only the device you want to reset.
594.R.EN.00
recycled paper versione 1.0
All products and technical specifications given in this document are subject to variation without notice. Unless previously
and specifically authorised by STAFER, the device must be used exclusively with transmitters produced by STAFER.
STAFER cannot be consider responsible for damage caused by improper, incorrect or unreasonable uses.
STAFER shall not be liable for damage resulting from improper, incorrect or unreasonable use.
STAFER S.p.a. - via Malpighi, 9 - 48018 Faenza (RA) ITALY
Tel. (+39) 0546.624811 - Fax. (+39) 0546.623141
Bring the motor
to an
intermediate
position
A
B
Only available with sensor 593KXS00, 593KXB00.
In the case of 10 channels trasmitter select the correct radio channel.
01. Bring the motor on the intermediate position.
02 By trasm. 594: press MENU for about 5 seconds; rS appears on the display
By trasm. 593: while press STOP also press PROG for about 1 sec., until the LED
lights up.
03. By trasm. 594: press one time PREV and 7 times NEXT. 17 appears on the
display.
By trasm. 593: press once UP and 7 times DOWN.
04. Press one time STOP. The receiver signals the current value.
Function active: p 1 (1 short upward movement)
Function not active: q 1 (1 short downward motion)
05. By trasm. 594: press PREV to disable the function (Of appears on the
display) or NEXT to enable the function (On appears on the display).
By trasm. 593: press DOWN to disable the function or UP to enable the function.
06. Press one time STOP. The receiver signal the new value.
Function active: p 1 - Function not active: q 1
A BB
Bring the motor
to an
intermediate
position
01. Bring the motor on the intermediate position.
02 By trasm. 594: press MENU for about 5 seconds; rS appears on the display
By trasm. 593: while press STOP also press PROG for about 1 sec., until the LED
lights up.
03. By trasm. 594: press 7 times NEXT. 07 appears on the display.
By trasm. 593: 7 times DOWN.
04. Press 1 time STOP. The receiver signals the current value. Example:
if it gets up for sec. = 2: p 2 ( 2 short upward movements)
if it gets up for sec. = 35: p 3 - pause - p 5
if it gets up for sec. = 120: p 1 pause p 2 pause p 1long
05. Using PREV/DOWN and NEXT/UP to set the new value:
for time = 3: 0 time PREV/DOWN and 3 times NEXT/UP
for time = 15: 1 time PREV/DOWN and 5 times NEXT/UP
(must be between 5 and 240)
06. Press one time STOP. The receiver signal the new value.
In the case of 10 channels trasmitter select the correct radio channel.
B
Bring motor
to an
intermediate
position
A
01. Bring the motor on the intermediate position.
02. By trasm. 594: press MENU for about 5 seconds. rS appears on the display
By trasm. 593: while press STOP also press PROG for about 1 sec., until the
LED lights up.
03. By trasm. 594: press 1 time PREV and 2 times NEXT. 12 appears on the display
By trasm. 593: press 1 time UP and 2 times DOWN.
04. Press 1 time STOP. The receiver signals the current value.
Example: if the parameter value = 4: p 4 (4 short upward movements)
05. By trasm. 594: using PREV and NEXT to set the new value (from 1 to 5.
1 is inactive. Factory set 1).
Example: for parameter = 4: (0 time PREV) - 4 times NEXT
By trasm. 593: press DOWN the number of times equal to the desired setting
(from 1 to 5. 1 is inactive. Factory set 1).
06. Press 1 time STOP. The receiver signal the new value.
In the case of 10 channels trasmitter select the correct radio channel.
A
BB
Bring motor
to an
intermediate
position
01. Bring the motor on the intermediate position.
02. By trasm. 594: press MENU for about 5 seconds. rS appears on the display.
By trasm. 593: while press STOP also press PROG for about 1 sec., until the LED
lights up.
03. By trasm. 594: press 8 times NEXT. 08 appears on the display.
By trasm. 593: 8 times DOWN.
04. Press one time STOP. The receiver signals the current value. Example:
if time = 2 sec: p 2 (2 short upward movements)
if time = 5 sec: p 5 (5 short upward movements)
05. By trasm. 594: using PREV and NEXT to set the new value:
for time 3 sec: 0 times PREV and 3 times NEXT
By trasm. 593: press DOWN the number of times equal to the desired setting.
06. Press 1 time STOP. The receiver signal the new value.
In the case of 10 channels trasmitter select the correct radio channel.
BB
In the case of 10 channels trasmitter select the correct radio channel to be resetted.
01. Bring the motor on the intermediate position.
02. By trasm. 594: press MENU for around 5 seconds. rS appears on the display.
By trasm. 593: while press STOP also press PROG for about 1 sec., until
the LED lights up.
03. By trasm. 594: press 2 times PREV and 9 times NEXT. 29 appears on the display
By trasm. 593: press 2 times UP and 9 times DOWN.
04. Press 1 time STOP. The receiver signals that it is ready for the memory reset
(with visual or acoustic signals, see the receiver instruction manual); on the
transmitter, all the leds and display segments come on intermittently for a few
seconds.
05. By trasm. 594: press together PREV and NEXT
By trasm. 593: for about 2 secondspress together UP and DOWN
The receiver signals that the factory settings have been restored (1 moviment up
and down).
06. Follow the instruction manual of the receiver to re-install the receiver.
Bring motor
to an
intermediate
position
A
