STA-RITE enviroMAX Manuel utilisateur
OWNERS MANUAL
Should the installer or owner be unfamiliar with the correct installation or operation of this type of
equipment you should contact the distributor/manufacturer for the correct advice before proceeding
with the installation or operation of this product. The pump operator or owner must be provided with
this owner’s manual.
For the Installation, Operation and Service of the
Variable Speed Pool Pump
1100
enviroMAX
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:33 AM
Table of Contents
Features and Benefits
Technical Information
Model Data
Hydraulic Performance
Dimensions
Installation
Pump Positioning
Piping
Pool Outlets
Electrical
Equipotential Bonding
Operation
Priming the Pump
Control panel overview
Operating the pump - Speed selection
Operating the pump - Variable speed adjustment
Operating the pump - Control panel operation
Operating the pump - Override
Operating the pump - Schedule advance
Operating the pump - Key lockout
Operating the pump - Time out
Operating the pump - Factory defaults
External control
Service & Maintenance
Troubleshooting
Troubleshooting Guide
Spare Parts
Pump parts exploded view
Spare parts table
Page
3
4
5
5
6
6
7
7
7
8
9
10
11
11
12
12
13
13
14
15
16, 17
4, 5
6
7
16
18
10
18
19
1100
enviroMAX
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:33 AM
Features & Benefits
The Sta-rite enviroMAX is the ideal pump for new or existing pools. Utilising advanced hydraulic design and
the latest technology in permanent magnet, variable speed motors, the Sta-rite enviroMAX has the perfect
combination of efficiency and performance. The Sta-rite enviroMAX delivers energy savings and the power
when you need it. You will also have the peace of mind that you are doing your bit for the environment and
reducing your carbon foot print.
Variable speed pump, with 4 programmable speeds, allows you to effortlessly select the most
efficient setting to meet you filtration, cleaning and water feature needs.
Radial flux, brushless permanent magnet motor delivers high efficiency and low noise levels.
Fault protected motor prevents damage by automatically shutting down the motor in the event of a
locked rotor, under voltage, over voltage or over current condition and will automatically reduce the
speed during an over temperature condition.
Precision-fit internal components and superior hydraulic design deliver effortless performance,
energy savings and extended pump life.
A specially designed sound-dampening pump casing and base make pump operation incredibly
quiet.
Constructed of our durable, thermoplastic, composite resin, so you can be sure it will stand up to
the harshest conditions.
A heavy-duty construction and a motor rated for continuous operation make the enviroMAX a tough,
long-lasting performer.
The high-capacity trap holds a large amount of debris, so you clean less often.
The Cam and Ramp™ lid is easy to remove and locks in place with a quarter turn, making inspection
and cleaning a breeze.
Quick-disconnect plumbing unions.
3
1100
enviroMAX
The Eco Select® brand identifies our most eco-friendly products
As the global leader in pool and spa equipment, we've made a strong commitment to develop and offer the
most environmentally responsible products available.
®
When you see the Eco Select brand on one of our products, you'll know it is our “greenest” and most
efficient product in that equipment category.
These products do the best job of saving energy, conserving water, reducing noise, or otherwise
contributing to a more environmentally responsible equipment system. In every case, a product that earns
the Eco Select brand is clearly our “greenest” and most efficient choice.
®
Eco Select
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:34 AM
Technical Information
Maximum Ratings: 3450RPM, P1 1375W, P2 1100W, 10.0A
IP Rating: IP25
Inlet (Suction): ABS Barrel Union to suit 50mm PVC pressure pipe
to AS/NZS 1477
Outlet (Discharge): ABS Barrel Union to suit 50mm PVC pressure pipe
to AS/NZS 1477
Max Working Pressure: 260 kPa
Water Temperature Range: 5°C – 40°C
Maximum Ambient temperature: 5 5°C
Recommended pH Range: 7.2 - 7.8 (Guide Only)
Sound Power Level (Lwa):
Motor: Radial flux, permanent magnet, DC
Protection: Mains over voltage, mains under voltage, over temperature,
under temperature, locked rotor, over current, phase disconnect.
Supply cord: 10A, H07RNF, 2m.
Low: 69dB
Med: 63dB
High: 57dB
Override: 73dB
?
4
RPM: Step1 2600RPM (4 hours) default factory setting
Step2 2100RPM (4 hours) default factory setting
Step3 1600RPM (4 hours) default factory setting
Override / Adjustable Range: 600-3450RPM (2 hours)
Rated Current: Step1 5.4A (max)
Step2 3.2A (max)
Step3 1.7A (max)
Override: 10.0A
Input Power (P1): Step1 690W (max)
Step2 375W (max)
Step3 180W (max)
Override: 1375W (max)
Pump Power (P2): Step1 550W (max)
Step2 300W (max)
Step3 145W (max)
Override: 1100W (max)
Model: enviroFLO 1100
Electrical Rating: 230-240V 50Hz single phase
1100
enviroMAX
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:34 AM
Technical Information
Hydraulic Performance
Dimensions
Sta-rite enviroMAX Performance Chart
5
1100
enviroMAX
0.0
5.0
10.0
15.0
20.0
25.0
0.0 100.0 200.0 300.0 400.0 500.0
Head (m)
Flow (L/min)
3450RPM
3100RPM
2850RPM
2600RPM
2350RPM
2100RPM
1850RPM
1600RPM
1350RPM
1100RPM
850RPM600RPM
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:35 AM
Installation
The pump must be installed and serviced by a suitably qualified person in order to avoid
hazard. Incorrectly installed or tested equipment may fail, causing severe injury or property
damage.
These instructions are a guide only. Should you the installer or owner of the product be
unfamiliar with the correct installation or operation of this product you should contact a
suitably qualified person for advice.
Do not connect system to high pressure or mains water system.
This pump is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the pump.
The enviroMAX is electrically connected. Ensure that it is isolated from electrical supply
during installation and any subsequent service work.
1. Plan the position of the pump
a) Have enough ventilation to keep ambient temperature below the motor's rated ambient temperature whenever the pump
is running. If installed in an enclosure/pump house, the enclosure must have adequate ventilation (200sq.cm min, inlet &
outlet) and air circulation Allow 200mm to keep rear of motor clear.
b) Have adequate floor drainage to prevent flooding and be protected from excess moisture.
c) Be solid, level, rigid and vibration free.
d) To reduce vibration and pipe stress, bolt pump to mount. Fixing holes accept 12mm fasteners.
e) Be within 2m of a power outlet for electrical connection (refer to AS/NZS 3000 for rules regarding connection of
electrical equipment in pool zones).
f) Allow adequate access for servicing pump and piping.
g) Allow for 250mm of straight pipe on the suction and discharge.
2. Piping
For best performance, allow pump
suction inlet height to be as far
below water level as possible and
allow the use of short, direct suction
pipe with minimum bends (to reduce
friction losses).
a) Use only Australian Standard PVC pressure pipe. For best performance use at least 50mm diameter pipe for all
connections to the pump. Never use a suction pipe smaller than pump suction connections (50mm) and use larger pipe
for long suction distances.
b) To avoid stress on the pump, support both suction and discharge pipes independently. Place these supports as close to
the pump as possible.
c) To avoid a strain left by a gap at the last connection, start all piping at the pump and run pipe away from the pump.
6
1100
enviroMAX
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:35 AM
Installation
3. Pool Outlets
a) The pump suction system must provide protection against hazard of suction entrapment or hair
entrapment/entanglement. The pool outlet piping must be in accordance with the latest AS1926.3 standard
b) Suction outlet covers and skimmers must have been tested and found to comply with the latest AS1926.3 standard or
ASME/ANSI specification for Suction Fittings.
4. Electrical
a) Electrical installation shall be in accordance with the national wiring rules (AS/NZS 3000) taking into account its ratings
(Class I, IPX5). The pump is supplied with a standard Australian 10 amp plug and 2 metres of cord. Select the correct
Pool Zone for installation.
b) An RCD with maximum rated residual current of 30mA is required for the power supply to the pump. Additionally, if a
suitable socket outlet is not available a weatherproof socket must be installed by an electrician in a suitable location.
RCD tripping indicates an electrical problem. If RCD trips and will not reset have a qualified electrician inspect and repair
electrical system.
c) Incorrect voltage can cause fire or seriously damage pump and voids warranty.
d) Voltage at pump must not be more than 6% above or 10% below motor nameplate rated voltage or pump may overheat,
causing overload tripping and reduced component life. If voltage is less than 90% or more than 106% of rated voltage
when pump is running at full load, consult the power company.
Do not use extension leads as they
are unsafe in and around the
Pool Zone.
Hazardous voltage. Can shock,
burn or cause death.
To avoid dangerous or fatal electrical
shock, turn OFF power to pump and
remove plug from outlet before
working on electrical connections.
5. Equipotential bonding
If equipotential bonding is required (refer to local statutes and regulations), connect all metal parts of the swimming pool or
spa structure and to all electrical equipment, metal conduit, and metal piping in accordance with the wiring rules. Run a
wire from the equipotential bonding terminal on the pump to the pool bonding structure.
The enviroMAX is double insulated to water circuit.
7
1100
enviroMAX
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:35 AM
Operation
NEVER run pump dry. Running pump dry may damage seals, causing leakage and flooding.
Fill pump with water before starting motor.
Freezing conditions will damage the unit, as water expands as it freezes. Ensure that the
enviroFLO is located so that it is not prone to freezing, or ensure that the product is
disconnected and dried of water during cold conditions.
Trapped air in system can cause explosion. Ensure all air is out of the system before
operating or testing equipment
Fire and burn hazard. Modern motors run at high temperatures. To reduce the risk of fire,
do not allow leaves, debris, or foreign matter to collect around the pump motor. To avoid
burns when handling the motor, let it cool for at least 20 minutes before trying to work on
it.
Small children using pool must ALWAYS have close adult supervision
Pump suction is hazardous and can trap and drown or disembowel bathers. Do not use or
operate pump, pool/spas if a suction outlet cover is missing, broken, or loose. Follow the
guidelines below for a pump installation which minimises risk to users of pool and spas.
NEVER tighten or loosen trap lid while pump is operating.
It is not necessary to lubricate the o-ring.
The original equipment O-ring contains a
permanent internal lubricant.
a) Before removing trap lid, SWITCH OFF POWER SUPPLY to pump.
b) CLOSE SHUT-OFF VALVES on suction and discharge pipes, if present.
c) Remove the trap lid (turn anti-clockwise)
d) Fill trap tank with water.
e) Check the lid o-ring and sealing surface, ensure there is no dust or debris on either, and replace the lid (turn clockwise to
tighten by hand only - no wrenches!).
f) Open the shut-off valves on the suction and discharge pipes, if present.
g) Release all air from filter, pump and piping system (refer filter owner's manual). In a flooded suction system (water
source higher than pump), pump will prime itself when suction and discharge valves are opened and air is released.
h) Switch on power to the pump to start.
I) Pump should start to prime now. Priming time will depend on vertical height of suction lift and horizontal length of
suction piping but is generally between 30 seconds to 3 minutes under normal installation conditions.
j) The enviroFLO will start slowly but ramp up to 2850RPM speed for the first 3 minutes to assist priming. It will then
switch to the selected speed (Step1).
* Should the pump not prime, ensure that all valves are open, lint trap is clear of debris and suctions and suction pipe end is submersed
in water, and that there are no leaks in suction pipe. See troubleshooting guide.
1. Priming the pump
8
1100
enviroMAX
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:35 AM
Navigation Overview
• +, - keys Increase/decrease selected value.
• Pressing any key following a change accepts the current value displayed inside the setting.
Figure 3: Control Panel
Programming
Buttons(x4)
PowerLED
FaultLED
Start Button
Stop Button
Active Step
LEDs(x4)
SpeedLED
Duration(Hrs.)LED
Bar Graph
+/-Buttons
Operation
1100
enviroMAX
2. Control panel overview
!CAUTION
If power is connected to the enviroMAX motor, pressing any of the following buttons referred to in this section
could result in the motor starting. Failure to recognize this could result in personal injury or damage to
equipment.
Note: The START button must be pressed for the pump to operate. The START LED will illuminate after the
button has been pressed indicating the pump is capable of operating. Pressing the stop button will turn off
the START LED and stop the motor if running.
9
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:35 AM
Operation
3a. Operating the pump - Speed selection
Speed / Application
The Sta-rite enviroFLO comes pre-programmed with the following default speeds:
Start/Stop buttons
Press Start to turn start pump. Press Stop to stop pump.
If power is removed, motor will return to STEP1.
Motor will remember ON/OFF state.
If the default speed settings do not perfectly match the particular installation, they can be adjusted as follows:
(To ensure the pump performs according to the energy rating label it is recommended to use the default low speed
setting of 1600RPM, for pool filtering).
Filtration and
water circulation
Cleaning with an
automatic suction
cleaner
Backwashing
filter.
Operating some
water features such
as jets or waterfalls.
Solar heating
Manual vacuum
2600RPM 2100RPM 1600RPM
Press for high speed Press for medium speed Press for low speed
1.
2.
Press Stop, then the Step# button, corresponding to the speed you
wish to change. Firstly the LED above duration is lit (you can press
+,- buttons to change duraton in 2 hour segments). Press again so
that the LED above “SPEED” is lit.
Press ‘-’ to decrease speed by one level with 600rpm as the
minimum limit.
Press ‘+’ to increase speed by one level with 3450rpm as the
maximum limit.
The speed setting will be automatically saved.
or or
Note: If power is cycled to the pump and the
user does not press the STOP key, the pump
will automatically start and run the
programmed default schedule shown in the
chart above. This feature ensures that the
pump will re-start in the event of a
power outage. The pump will start on STEP 1.
Note: The pump must be Stopped (Press STOP
Key) when programming the DURATION and
SPEED of the STEP 1, STEP 2, and STEP 3
keys. OVERRIDE DURATION and SPEED can
be programmed when the pump is either
stopped or running.
Note: The pump can only be set to operate on a
24-hour schedule. If a user attempts to
program a schedule with a combined duration
for all three steps greater than 24 hours, the
pump software will retain the current STEP
time duration only, and will zero out the other
two STEP time settings. As an example, if STEP
1 equals eight (8) hours, STEP 2 equals nine (9)
hours, and STEP 3 equals eight (8) hours – for
a combined 25 hours – the pump will retain the
setting for the current Step being programed
and zero out the remaining two.
1100
enviroMAX
3b. Operating the pump - Variable Speed Adjustment
10
3100RPM
Override
L300241_EnviroMAX_OM
Monday, 11 August 2014 10:18:35 AM
Table des matières
Autres manuels STA-RITE Pompe de piscine
STA-RITE
STA-RITE CSP Series Manuel utilisateur
STA-RITE
STA-RITE PCD-10B Mode d’emploi
STA-RITE
STA-RITE JTACL1/2 HP Manuel utilisateur
STA-RITE
STA-RITE DYNA-GLAS Manuel utilisateur
STA-RITE
STA-RITE MAX-E-GLAS PE Series Manuel utilisateur
STA-RITE
STA-RITE ABG Series Manuel utilisateur
STA-RITE
STA-RITE WATERFORD SYSTEMS JWPS5EL Manuel utilisateur
STA-RITE
STA-RITE JTACLC-A Manuel utilisateur
STA-RITE
STA-RITE IntelliPro VS-3050 Manuel utilisateur
STA-RITE
STA-RITE JSAL15D-06 Manuel utilisateur
STA-RITE
STA-RITE D Series Manuel utilisateur
STA-RITE
STA-RITE ABG Series Manuel utilisateur
STA-RITE
STA-RITE S5P Series Manuel utilisateur
STA-RITE
STA-RITE PRC Series Manuel utilisateur
STA-RITE
STA-RITE 60 CYCLE C Series Manuel utilisateur
STA-RITE
STA-RITE JWPA5DL-A Manuel utilisateur
STA-RITE
STA-RITE Dyna-Wave Manuel utilisateur
STA-RITE
STA-RITE MAX-E-PRO Manuel utilisateur
STA-RITE
STA-RITE JWPA5C Manuel utilisateur
STA-RITE
STA-RITE JW Series Manuel utilisateur
Manuels Pompe de piscine populaires d'autres marques
Resol
Resol DeltaSol B Pro Manuel utilisateur
Evolution Aqua
Evolution Aqua UniTech Perfect 5000 Manuel utilisateur
Outside Living Industries
Outside Living Industries Ubbink Heatermax Pool Guide de démarrage rapide
CPI
CPI Olympic 2P1815 Manuel utilisateur
Flotec
Flotec FP6121-01 Manuel utilisateur
Pentair
Pentair ONGA LEISURETIME LTP400 Manuel utilisateur