SRP BRL40 Series Manuel

Series BRL40 Page 1 LT234 August 2019

Installation, Operation and Service Instructions

INFRARED BROODER

SERIES

BRL40

WARNING

FOR YOUR SAFETY

Improper installation, adjustment, alteration, service

or maintenance can cause property damage, injury or

death. Read the installation, operating and

maintenance instructions thoroughly before installing

or servicing this equipment.

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

If you smell gas:

1. Open windows

2. Don’t touch electrical switches

3. Extinguish any open flame

4. Immediately call your gas supplier

OWNER

INSTALLER

Retain this Manual & ensure available for service.

Improper installation, adjustment, alteration, service

or maintenance can cause injury, death or property

damage.

Read the installation, operation and service

instructions thoroughly before installing or servicing

this equipment

Provide Manual to Owner upon completion of

installation!

Read and thoroughly understand these Instructions

before attempting any installation

Canada: 563 Barton Street, Stoney Creek, Ontario L8E 5S1

USA: 315 N Madison Street, Fortville, IN 46040

www.superiorradiant.com

Series BRL40 Page 2 LT234 August 2019

WARNING: FIRE OR EXPLOSION HAZARD

Maintain clearance to combustible constructions as further specified in this manual. Failure to do so

could result in a serious fire hazard. Heaters should not be located in hazardous atmospheres

containing flammable vapors or combustible dusts. Signs should be provided in storage areas

specifying maximum safe stacking height.

CAUTION: FIRE OR EXPLOSION HAZARD

This heater is equipped with an automatic ignition device. Do not attempt to light the burner by hand.

Failure to comply could result in a serious fire and personal injury hazard.

CAUTION: MECHANICAL HAZARD

Do not use high pressure (above 1/2 psi) to test the gas supply system with the burners connected.

Failure to do so could result in damage to the burner and its control components requiring replacement.

CAUTION: SERVICE LIFE RISK

Do not install equipment in atmospheres containing halogenated hydrocarbons or other corrosive

chemicals. Failure to do so may lead to premature equipment failure and invalidation of the warranty.

WARNING –California Proposition 65

This appliance, its related accessories and by-product of operation, contain chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

Series BRL40 Page 3 LT234 August 2019

CONTENTS

CONTENTS ............................................................................................................................................................................. 3

INTRODUCTION...................................................................................................................................................................... 4

INSTALLATION CODES ...................................................................................................................................................................... 4

GENERAL SPECIFICATIONS ..................................................................................................................................................... 5

INPUT .......................................................................................................................................................................................... 5

GAS SUPPLY .................................................................................................................................................................................. 5

ELECTRIC SUPPLY............................................................................................................................................................................ 5

VENTILATION ................................................................................................................................................................................. 5

SHIPPING CONFIGURATION ............................................................................................................................................................... 5

HIGH ALTITUDE RATINGS ................................................................................................................................................................. 5

DIMENSIONAL CHARTS .......................................................................................................................................................... 5

BROODER PARTS.................................................................................................................................................................... 6

GENERAL ASSEMBLY ....................................................................................................................................................................... 7

PACKAGE CONTENTS.............................................................................................................................................................. 8

CLEARANCE TO COMBUSTIBLES ............................................................................................................................................. 9

ASSEMBLY............................................................................................................................................................................ 10

INSTALLATION...................................................................................................................................................................... 14

VENTING & COMBUSTION AIR ............................................................................................................................................. 15

GENERAL REQUIREMENTS .............................................................................................................................................................. 15

GAS PIPING .......................................................................................................................................................................... 16

ELECTRICAL CONNECTIONS .................................................................................................................................................. 18

WIRING DIAGRAM ........................................................................................................................................................................ 18

LIGHTING AND SHUTDOWN INSTRUCTIONS......................................................................................................................... 20

STARTING SEQUENCE OF OPERATION ................................................................................................................................................ 20

FUEL CONVERSION KIT ......................................................................................................................................................... 21

MAINTENANCE .................................................................................................................................................................... 23

TROUBLESHOOTING ............................................................................................................................................................. 24

REPLACEMENT PARTS .......................................................................................................................................................... 25

WARRANTY .......................................................................................................................................................................... 26

Series BRL40 Page 4 LT234 August 2019

INTRODUCTION

Superior Radiant Products is a company in the infrared heating industry founded on the principles of product quality

and customer commitment.

Quality commitments are evidenced by superior design, a regard for design detail and an upgrade of materials

wherever justifiable.

Customer commitment is apparent through our ready responses to market demands and a never ending training

and service support program for and through our distributor network.

The series BRL is an infrared brooder for agricultural installations.

IMPORTANT

The manufacturer’s instructions, the layout drawing, national and local codes and ordinances, and all applicable

standards which apply to gas piping and electrical wiring comprise the basic information needed to complete the

installation. These criteria must be thoroughly understood before proceeding.

Only personnel who have been trained and understand all applicable codes should undertake the installation.

Manufacturer representatives are Factory Certified in the service and application of this equipment and can be

called on for helpful suggestions about installation.

Installation Codes

Installations must comply with local building codes, or in their absence, the latest edition of the national regulations

and procedures as listed below.

This heater complies with IAS U.S. No. 8-94 (Draft No. 2) and CAN-1-2-20-M85.

General Installation and Gas Codes

Heaters must be installed only for use with the type of gas appearing on the rating plate, and the installation must

conform to the National Fuel Gas Code, ANSI Z223.1/NFPA 54 in the US and CSA B149.1 Installation Code in

Canada.

Not for use in residential dwellings, refer to Rating plate.

Gas Supply Lines

Gas supply pipe sizing must be in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 in the US

and CSA B149.1 Installation Code in Canada.

A 1/8" NPT plugged tap must be installed in the gas line connection immediately upstream of the burner farthest

from the gas supply meter to allow checking of system gas pressure.

Electrical

All heaters must be electrically grounded in accordance with the National Electric Code, ANSI/NFPA 70 in the US,

and the Canadian Electric Code, CSA C22.1 in Canada, and must comply with all local requirements.

Series BRL40 Page 5 LT234 August 2019

GENERAL SPECIFICATIONS

Input

40,000 BTU/hr

Gas Supply

Inlet Pressure

Natural Gas:

Minimum

Maximum

5.0”W.C.

14.0”W.C.

Propane Gas:

Minimum

Maximum

11.0” W.C.

14.0”W.C.

Manifold Pressure

Natural Gas:

4” W.C.

Propane Gas:

10”W.C.

Inlet Connection

Natural Gas or Propane: 3/8” female NPT

Electric Supply

24 VAC, 60 HZ, 0.8 Amp

Ventilation

For indoor installation only and unvented. Minimum ventilation required is 160 CFM per brooder.

Shipping configuration

This heater ships from the factory for use with LP gas. To convert from propane to natural gas, refer to

Gas Conversion Instructions within this manual.

High Altitude Ratings

40,000 BTU/hr. For Canada 0-4500 feet above sea level. In the U.S. 0-2000 feet above sea level, anything

over 2000 feet is derated by 4% per thousand feet above sea level as per National Fuel Gas Code.

DIMENSIONAL CHARTS

Figure 1: Overall Dimensional Information

Series BRL40 Page 6 LT234 August 2019

BROODER PARTS

Get to know your heater parts (list referencing Figure 2).

Figure 2: General Overview

Series BRL40 Page 7 LT234 August 2019

General Assembly

Refer to Figure 2 for component identification.

No.

Qty

Description

No.

Qty

Description

CH118

Screw S/S #8-32x3/8” Pan Phillips

BS014

Brooder Main Hanging Bracket

CH095

Washer, Flat 3/16 x 3/4”

BE008

Control Box Assembly

BS001

Dust Pan

BS012

Control Box Mounting Bracket

BG005

Brass Adapter

BS011

Heat Shield

UG029

Orifice #49 LPG

BS010

Manifold Mounting Bracket

BG010

Brooder Burner

BG003

WR Gas Valve 25M18-716

BS006

Brooder Cone Assembly

BE004

Ignition Cable 35”

CH190

Keps Nut #10-24

BG006

Brass Tube Fitting, 3/8 NPT to 3/8

Pressure Fitting Female

CH051

Hex Head Bolt S/S 1/4”-20

BG007

Gas Tube, 3/8 S/S

BS009

Cone Hanging Bracket

BS005

Electrode Bracket

BS013

Reflector

BE003

Electrode PSE-GF26

CH143

Washer, 1/4” flat S/S

BS004

Spacer Screw #10-24

CH260

Keps Nut S/S 1/4”-20

BS003

Burner Top Plate

CH261

304 S/S Eyebolt 1/4”-20 x 1”

NO.

QTY

DESCRIPTION

BE006

Controls Enclosure

BE002

Ignition module

Weld Bolt #10-24 x 1", S/S

CH130

Screw, 8-32 x 3/4" Pan Phillips

Lid

Lid Screw

CH262

Liquid Tight Fitting PG11

BE007

ON/OFF switch

BE009

Terminal Block

BS016

Module Mounting Plate

CH190

Keps Nut #10-24

*12

CE280

WAGO 3 Conductor Lever Nut

*Not shown in diagram; only used in conjunction with gas valve 25M18-716B1

Figure 3: Control Box (BE008) Components

Series BRL40 Page 8 LT234 August 2019

PACKAGE CONTENTS

The radiant brooder is sold in packages of six or one, depending on the customer’s quantity order. Verify that you

have received all heater components included with the unit. The unit is packaged as sub-assemblies in kits, listed

below. To purchase replacement parts, refer to page 23.

BS013 - Reflector

BK006 Emitter Cone Assembly

BS001 - Dust Pan

BK001- Hanger Kit

BK002 - Heat Shield Kit

BG010 - Burner

BE008 - Control Box Kit

BK004 - Electrode Assembly Kit

BK003 - Manifold Assembly

BK014 - Natural Gas Conversion Kit

Figure 4

Series BRL40 Page 9 LT234 August 2019

CLEARANCE TO COMBUSTIBLES

Minimum clearances to combustible materials shall be measured from outer surface of the reflector.

In addition to this it is very important to observe the minimum clearance to combustibles at all times to

avoid any possibility of property damage or personal injury.

Combustible materials are considered to be wood, compressed paper, plant fibres, plastics, Plexiglas or other

materials capable of being ignited and burned. Such materials shall be considered combustible even though flame-

proofed, fire-retardant treated or plastered.

The stated clearance to combustibles represents a surface temperature of 90°F (50°C) above room temperature.

Building materials with low heat tolerance (i.e. plastics, vinyl siding, canvas, tri-ply, etc.) may be subject to

degradation at lower temperatures.

It is the installer’s responsibility to ensure that adjacent materials are protected from deterioration.

64’’ (1625mm)

36’’ (915mm)

15’’ (380mm)

Table1: Minimum clearance to combustible materials

Figure 5: Clearance to Combustible

Series BRL40 Page 10 LT234 August 2019

ASSEMBLY

1. Before assembling, check that all components are included in the package.

2. Fasten the burner assembly to the cone assembly using three (3) #10-24 hex locknuts, and attach the

igniter bracket to the burner assembly using a #10-24 hex locknut, as shown in Fig. 6.

Figure 6

3. Fasten the short end of the hanging bracket (with eyebolt) to the centre hole of the reflector, using a ¼”-20

S/S bolt and appropriate washer and locknut. Align the other end of the hanging bracket with the alignment

holes on the reflector. Attach the cone assembly to the reflector, aligning the igniter bracket with the

alignment holes, using ¼”-20 hex nuts and ¼ flat washers.

Figure 7

Table des matières

Autres manuels SRP Chauffage

SRP

SRP UAB SERIES Manuel

SRP

SRP S Series Manuel

SRP

SRP WTH Series Manuel

SRP

SRP BIG SHOT Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur