SRLine R-FLAT Manuel utilisateur

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 1

SR-Line

Industry monitors

USER MANUAL

Booth: 22.12.2022

Reproductions of any kind, even as excerpts, require the written permission of SR System Elektronik GmbH.

ATTENTION: This document will not be withdrawn when a new edition is published, all previous

editions will lose their validity.

 
 
 
 
SR 
SYSTEM-ELEKTRONIK 
GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com 
 
 Seite | 2 
Table of contents 
Content 
Table of contents..................................................................................................................................... 2 
Electrostatic sensitive modulesl.............................................................................................................. 4 
General.................................................................................................................................................... 5 
Introduction............................................................................................................................................. 6 
Definition, abbreviations......................................................................................................................... 7 
Definition................................................................................................................................................. 7 
Abbreviations .......................................................................................................................................... 7 
Safety instructions................................................................................................................................... 8 
Putting the TFT monitor into operation.................................................................................................. 9 
Notes on compliance with the EMC Directive (CE mark)...................................................................... 10 
EMV ....................................................................................................................................................... 10 
Model variants....................................................................................................................................... 11 
VESA-DPMS / Behavior without video signal ........................................................................................ 11 
Auto signal detection ............................................................................................................................ 12 
Characteristics....................................................................................................................................... 12 
VESA- mounting..................................................................................................................................... 12 
Environmental conditions ..................................................................................................................... 12 
Service OSD ........................................................................................................................................... 13 
Functions and keys................................................................................................................................ 13 
Hotkeys.................................................................................................................................................. 13 
OSD Status (external LED`s)................................................................................................................... 13 
OSD Menu Overview ............................................................................................................................. 14 
Menu „Picture“...................................................................................................................................... 14 
Menu „Display“ ..................................................................................................................................... 14 
Menu „Color“ ........................................................................................................................................ 15 
Menu „Other“........................................................................................................................................ 15 
Menu „Advance“................................................................................................................................... 16 
Menu „Audio“........................................................................................................................................ 16 
Hotkey Function Definition ................................................................................................................... 17 
Operation and repairs ........................................................................................................................... 18 
Cleanining.............................................................................................................................................. 19 
EMV and equipment safety................................................................................................................... 21 
Appendix................................................................................................................................................ 22 
DVI D24P................................................................................................................................................ 23 

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 3

HDMI D24P............................................................................................................................................ 24

AC supply............................................................................................................................................... 25

DC- Plug 12 / 24 V.................................................................................................................................. 25

Grounding bolt ...................................................................................................................................... 25

IR Remote Control (Option)................................................................................................................... 26

Modified

Chapter

/ Page

Output

stand

Reason for change

22.12.2022

Creation of this document

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 4

Electrostatic sensitive modulesl

Electronic components can be damaged or destroyed by electrostatic

discharges. This does not necessarily lead to a failure of the module, it can

also result in malfunctions! The following instructions must therefore be

observed:

•

Before working on the open unit, any charge on the body must be discharged by

touching the grounded housing parts.

•

The same applies, of course, to any (protective-insulated) tools to be used. This

must also be discharged on a grounded object.

•

If you removeor add modules from the system, the device must always be switched

off or disconnected from the supply voltage.

•

You should always touch modules only at the edge. Touching the conductor tracks

and connection pins must be avoided at all costs.

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 5

General

The operating manual is intended to assist you with the assembly, installation and operation

of the flat panel monitor. Please read through the manual completely once, as information

relating to several chapters is only reproduced once. Keep the manual in a safe place. Follow

all instructions and warnings marked on the product itself. Do not use any liquid or

corrosive cleaning agents. Use a damp, lint-free cloth for cleaning. Never operate the device

near water.

Never place the device on an unstable surface. All slots and openings on the bottom and

back of the device are used for ventilation to adequately protect the device from

overheating. These ventilation slots must never be covered. The unit must never be placed

near or on a radiator or other heat source. The unit must always be connected to a power

supply according to the label on the back of the housing. Do not insert any objects through

the ventilation slots. Do not spill liquids on the unit. Leave all repairs to qualified personnel.

Do not expose the unit to direct sunlight.

SR assumes no warranty, legal responsibility or any liability for consequences resulting from

incorrect information. Changes to the scope of performance and technical data can be made

at any time and without special notification.

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 6

Introduction

This LCD display functions as a video-compatible color display.

The monitor is used to drive digital TFT displays with resolutions from 640 x 480 up to 1920 x

1080 dots directly with the standard video signals of PCs and workstations.

A special graphics card is not required. The image signal is supplied via a normal monitor

cable.

Video modes with lower resolutions than the TFT resolution can be expanded as required,

thus using the full display area of the display. By using high-quality filters, the image content

is preserved. Since the video signals from PCs and workstations are not subject to any

standardization in terms of timing, the image position can be adjusted in all parameters for

special variants. All necessary adjustments are made via an easy-to-use OSM menu (on-

screen manager) and only have to be made once; the selected parameters are saved.

The monitor is supplied via the integrated wide-range power supply or via an external

voltage source. All other voltages necessary for the operation of the board and the display

are generated on board.

The TFT monitor has the following features:

•

robust, industrial design

•

optionally equipped with touch screen

•

EMC-compliant design for increased noise immunity and reduced interference

radiation, CE mark and declaration of conformity for tested variants

•

compatible to industrial standard

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 7

Definition, abbreviations

Definition

Abbreviations

OSD On Screen Display

MHz Number of oscillation processes in millions of oscillations per second

KHz Number of oscillation processes in thousands of oscillations per second

Hz Number of oscillation processes in oscillations per second

H-Sync Indicates the start of transmission of a new line. Serves for synchronization

between an image source and a receiver.

V-Sync Indicates the start of transmission of a new line. Serves for synchronization

between an image source and a receiver.

European Union Declaration of Conformity

Direct current DC

~Alternating current AC

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 8

Safety instructions

The TFT monitor is designed for use in industrial and commercial areas. The

person who installs the device is responsible for safety, compliance with

occupational safety and accident prevention regulations, and all other legal

requirements.

Commissioning, setup and repair work may therefore only be carried out by professionally

qualified personnel. The following safety instructions must be observed:

• When opening the rear panel of the unit, live parts may be exposed. The monitor unit must

therefore first be switched off and disconnected from the mains by taking appropriate

measures.

• If it is unavoidable to operate the unit in the open state during setup and repair work,

special care must be taken. No conversions may be carried out in this state. It cannot be

ruled out that this will cause short circuits which will result in damage to various

components.

• Due to the manufacturing process, it cannot be ruled out that sharp corners and edges

may protrude from printed circuit boards and sheet metal parts. Please handle with care to

avoid injuries.

• When the device is open, make sure that no electrically conductive foreign bodies, such as

metal chips and screws, can get into the device, as this can cause short circuits with serious

consequences.

This monitor can only be operated in an installation system. It must be adequately protected

against the following external influences: (installation precautions)

- Water, humidity above 85%.

- Touch of the user (except screen front)

- penetration of metal parts (smaller than 4mm)

- flammable substances and gases - heat above +50°C

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 9

Putting the TFT monitor into operation

Unpack device

The device is delivered in a sturdy cardboard box. The device is fixed in place and protected

from damage during transport by the tensioned Swing foil. Keep all parts for the time being

in order to have suitable transport packaging in case of a necessary return.

Check the device and the accessories supplied for transport damage. If damage is visible on the

device, it must not be put into operation, as safety could be impaired. Contact the sender

immediately!

Check the scope of delivery against the delivery bill.

Installation of the device unit

The device must not be exposed to excessive cold, heat, moisture or dirt. The ambient

conditions specified in the "Technical data" must be observed to maintain operational

safety!

Before attaching the device to a VESA mount, check whether the maximum permissible

weight for the mount is observed. This is specified by the manufacturer.

When mounting the device, make sure that sufficient ventilation of the device unit is

ensured.

Make sure that there is sufficient space for the connections and that no sharp edges or

corners protrude in this area. This could result in damage to the connection cables and

impair the function and safety.

Threaded bolts may be tightened to a maximum of 2.6 Nm!

SYSTEM-ELEKTRONIK

GmbH | Eschachstr. 23 | D-78078 Niedereschach | phone +49 77289268-0 | info@sr-line.com

Seite | 10

Notes on compliance with the EMC Directive (CE mark)

Within the EU, laws require compliance with uniform limit values for interference radiation

and interference immunity. The TFT monitor is built in such a way that these limits are

complied with. It is therefore provided with the CE mark and a declaration of conformity.

Outside the EU, the respective national regulations must be observed.

Devices that are connected to the TFT monitor must also comply with the corresponding

limit values. This is the only way to ensure that the entire system complies with the legal

regulations. Make sure that all devices have an appropriate test mark or manufacturer's

declaration.

The connection to the connected devices must be made via shielded cables. Cables with foil

shielding are less suitable than cables with braided shielding and a high degree of coverage.

The connector housing must have an all-round connection with the cable shield.

EMV

• This is a Class A device (industrial use). It may cause radio interference in residential

areas. In this case, the operator may be required to implement appropriate measures

and to pay for them.

• The present device serves as an installation component in an industrial application.

The operator of the overall system is required to comply with the electromagnetic

compatibility according to the EMV law.

Table des matières

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation