SPX FLOW 65000 Manuel utilisateur

Oil Change Kit

Model 65000, 65F3B

ORIGINAL INSTRUCTIONS/TRANSLATION OF ORIGINAL INSTRUCTIONS

READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR

SERVICING THIS PRODUCT

INSTRUCTION MANUAL

WARNING:

Do not use with gasoline, petrol, or ﬂuids with a ﬂash point below

100° F (38° C).

To prevent injury, always disconnect the power source when installing

or servicing an electrical product.

Always use the fuse amperage rating speciﬁed for your pump model.

Failure to do so may cause serious personal injury or ﬁre hazards. The

pump has been designed for non-continuous use. Under conditions of

high operating pressures (by closed or blocked outlet, excessive length

of the delivery circuit and/or excessive pressure due to accessories),

the pump can be stressed too much and overheat. Therefore it should

not be used for prolonged periods under such conditions. Do not

remove pump and supplied accessories or make any modiﬁcations

thereof.

INSTALLATION

The electrical installation of the pump must include a protection fuse which is properly

rated as indicated on the motor label. Warranty expires if a fuse is not utilized. Electrical

wire size should depend on the distance between the pump and battery supply. The

use of undersized wire may cause overheating of the electrical wiring and subsequently

cause a ﬁre hazard. There will also be a voltage drop at the motor terminals with a

subsequent reduction in efﬁciency. The ﬂow rate value indicated on the motor label is

obtained with a 13mm or approx. 1/2 in internal hose diameter on the outlet. Hoses

having inferior hosing will cause an increase in current with potential risk of motor

overheating. To ensure the correct directional ﬂow of the ﬂuid as indicated by the

arrow on top of the pump, it is necessary to connect the positive pole of the battery

supply to the (+) marked terminal on the motor end cap and negative pole to the (-)

marked terminal. Electrical connections must be made using suitable terminal blocks

and connectors ensuring a tight laying of the electrical cables. Improper wiring can

cause power losses and/or overheating of the wiring.

Warning: It will be the installer/Technicians responsibility to ensure a properly designed

circuit installation according to the electrical regulations and code. DO NOT Take

pump and parts apart for servicing or repairs.

OPERATING INSTRUCTIONS

1. If the engine is cool, run the engine for 5 minutes to raise the temperature of the

oil to a maximum of 120 F. Before attempting to remove oil, shut off the engine.

Increased oil temperatures should allow for better ﬂow, and reduce amperage

load on the pump/motor during use.

Remove the dipstick tube, and insert the small 1/4 in extraction tube to the bottom

of the oil pan or when reasonable resistance is felt. If assembled, the small tube

should be connected to the larger 3/8 in tube via push-to-connect union ﬁtting.

Ensure the other end of the 3/8 in tube is securely inserted into the push-to-connect

ﬁtting installed on the inlet side of the pump.

3. Take the alligator clips coming off the pump and clamp it to your battery. The Red

alligator clip will go to your positive terminal and the Black clip to your negative

terminal. Make sure the pump is appropriately fused through the positive connection.

4. Make sure that probe has bottomed out. A simple way to make sure the probe has

bottomed out is take a measurement of the distance from the top of the dipstick

tube to the bottom of the pan and visually mark this distance on the probe. When the

probe is bottomed out, slightly pull the probe up around ¼" and secure the probe

in that position for the duration of the oil removal process.

4a. If your pump is equipped with a polarily reversin switch (65F3B Kit), the pump will

only active when the switch is depressed in the direction of ﬂow. Oil should be drawn

into the inlet side of th epump, and released into the bucket and visible throught the

clear tube on the outlet side.

5. After oil is removed, do not leave the pump running dry for more than 30 seconds.

After the oil is removed from your engine, make sure the pump is switched off by

removing alligator clips from the battery. Disconnect the alligator clips from the

battery and carefully remove the dipstick probe from the dipstick tube.

To empty the container of used oil remove tab from pour spout of bucket, pull

spout out and SLOWLY pour out oil into an approved container for recycling and

appropriate disposal.

Note: Always recycle used oil in compliance with federal and local legislation. Handle

all petroleum products in an environmentally responsible way.

TROUBLE SHOOTING

Problem Solutions

Why doesn’t the pump start? Check the voltage on your battery

Check to make sure fuse is not blown

The average life span of the motor is 800-1000

hours under normal operating conditions. If the

pump is used beyond that, carbon brushes have

worn out, replace pump.

Why isn’t the pump priming? The pump has run dry for too long damaging the

internal components. Long periods of inactivity

may cause pump to lose prime.

Battery leads may be switched, ensure pump posi-

tive (Red) is connected to battery positive (+), and

pump negative (Black) to battery negative (-).

Polarity reversing switch may be depressed in the

incorrect ﬂow direction.

CARE AND MAINTENANCE:

No particular maintenance is required if the pump is employed for the transfer of

diesel ﬂuids or oils.

65000 TECHNICAL DATA:

Port connection: 13mm

Self Priming up to 1 meter

Capacity: 8 L/Min.

Dimensions: 12 x 12 x 19.5"

305 x 305 x 495 MM

Weight 5LBS. (2.3 KG)

Fuse Size: 8A

Complies with ISO 8846, EN 55014

65F3B TECHNICAL DATA:

Port connection: 3/8"NPT

Inlet: 3/8" Push-To-Connect x 3/8"NPT

Outlet: 1/2” Hose Barb x 3/8"NPT

Self Priming up to 1 meter

Capacity: 5.5 GPM (21LPM)

Dimensions: 12 x 12 x 19.5"

305 x 305 x 495 MM

Weight 5LBS. (2.3 KG)

Fuse size: 20A

WARRANTY INFORMATION

SPXFLOW JOHNSON PUMP of 5885 11th Street Rockford, Illinois 61109 warrants

to the original consumer purchaser that this product will be free from defects in

material and workmanship, providing that the case is not opened or the pump

otherwise abused for a period of one (1) year from the date originally purchased.

The exclusive remedy of the consumer purchaser in the event the product does not

meet this express Limited Warranty is to return the pump to SPXFLOW Johnson Pump

at the above address, freight prepaid with your sales receipt. IMPORTANT: FOR

THIS WARRANTY TO BE EFFECTIVE, SPXFLOW JOHNSON PUMP MUST BE

SUPPLIED WITH THE ORIGINAL PURCHASE DATE OF THE PRODUCT. THE

ACCEPTANCE BY JOHNSON PUMP OF ANY PRODUCT RETURNED SHALL

NOT BE DEEMED AN ADMISSION THAT SUCH PRODUCT IS DEFECTIVE OR

IN VIOLATION OF ANY WARRANTY. THE COMPANY RESERVES THE RIGHT

TO REPAIR OR REPLACE THE PRODUCT.

NO REPRESENTATIVE OR OTHER PERSON IS AUTHORIZED TO ASSUME FOR

SPXFLOW JOHNSON PUMP ANY ADDITIONAL LIABILITY IN CONNECTION

WITH THE SALE OF ITS PRODUCTS OR TO ALTER THIS WARRANTY IN

ANY WAY.

IN NO EVENT WILL SPXFLOW JOHNSON PUMP BE LIABLE FOR MORE THAN

THE SALES PRICE OF THE PRODUCT. UNDER NO CIRCUMSTANCES WILL

SPXFLOW JOHNSON PUMP BE LIABLE FOR ANY LOST PROFITS, INCIDENTAL

OR CONSEQUENTIAL COSTS, EXPENSES, OR DAMAGES. THE LIMITATION

ON LIABILITY FOR LOST PROFITS, INCIDENTAL OR CONSEQUENTIAL COST

EXPENSES OR DAMAGES SHALL SURVIVE ANY FAILURE OF ESSENTIAL

PURPOSE OF THIS LIMITED WARRANTY. Some states do not allow the exclusive

or limitation of incidental or consequential damages, so the above limitation may

not apply to you.

NO EXPRESS OR LIMITED WARRANTY, INCLUDING WARRANTY OF

MERCHANTABILITY AND FITNESS SHALL EXTEND FOR ANY PERIOD OF

TIME GREATER THAN ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE

OF THIS PRODUCT. Some states do not allow limitation on how long an implied

warranty lasts so the above limitation may not apply to you. CAUTION - Warranty

void if seal on product is broken, if any electric cord is cut, if electric splices become

submerged, or if product is installed contrary to instructions or warnings.

SPX FLOW, Inc. JOHNSON PUMP MARINE 5885 11th Street, Rockford, IL 61109-3699, U.S.A.

Tel 847-671-7867 Fax 800-288-7031

www.spxﬂow.com/johnson-pump-marine

65F3BMAN Printed July 2020

ISO

8846

8849

Recreational Craft Directive 94/25/EEC

ISO 8849: 1990/Electrical operated bilge pumps

ISO 8846: 1990/Electrical devices - Protection against ignition of

surrounding ﬂammable gases

ISO 10133: 1994/Electrical systems - Extra low-voltage DC installations

Electromagnetic Compatibility Directive 89/336/EEC

EN55014: 1993/Radio Disturbance

OIL CHANGE KIT:

MODEL 65000, 65F3B

For more information about our worldwide locations, approvals, certiﬁcations, and local representatives, please visit

www.spxﬂow.com/johnson-pump-marine

SPX FLOW, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation.

Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your

information only and should not be relied upon unless conﬁrmed in writing.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SPX FLOW Pompe à eau

SPX FLOW

SPX FLOW Infinity Series Manuel utilisateur

SPX FLOW

SPX FLOW Waukesha Cherry-Burrell Universal 1 Series Manuel utilisateur

SPX FLOW

SPX FLOW TopGear GP Series Manuel utilisateur

SPX FLOW

SPX FLOW CM90 BL Manuel utilisateur

SPX FLOW

SPX FLOW Johnson Pump CombiProLine OH3 Manuel utilisateur

SPX FLOW

SPX FLOW TopGear BLOC Series Manuel utilisateur

SPX FLOW

SPX FLOW ULTIMA BILGE 600 GPH Manuel utilisateur

SPX FLOW

SPX FLOW Universal TS Series Manuel utilisateur

SPX FLOW

SPX FLOW Universal 3 Series Manuel utilisateur

SPX FLOW

SPX FLOW Universal 5000 Industrial Series Manuel utilisateur

SPX FLOW

SPX FLOW Johnson Pump 10-13635-01 Manuel utilisateur

SPX FLOW

SPX FLOW C Series Manuel utilisateur

SPX FLOW

SPX FLOW Power Team P59L-1500 SERIES Manuel utilisateur

SPX FLOW

SPX FLOW Power Team PB102-1 Manuel utilisateur

SPX FLOW

SPX FLOW Johnson pump Manuel utilisateur

SPX FLOW

SPX FLOW Power Team PE172SM Manuel utilisateur

SPX FLOW

SPX FLOW PE10 Series Manuel utilisateur

SPX FLOW

SPX FLOW Power Team PB102 Manuel utilisateur

SPX FLOW

SPX FLOW Johnson Pump F35B-8 Series Manuel utilisateur

SPX FLOW

SPX FLOW Viking Power 32 Manuel utilisateur

SPX FLOW

SPX FLOW Bolting System RWP55-BS Manuel utilisateur

SPX FLOW

SPX FLOW Power Team PB104-0-ARC Manuel utilisateur

SPX FLOW

SPX FLOW Power Team AP02528 Manuel utilisateur

SPX FLOW

SPX FLOW PQ60 Series Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur