Sprog SBOOST Manuel utilisateur
SBOOST User Guide 1
Version 1.4 February 2012 © Copyright 2012SPROG DCC
SBOOST DCC Booster
User Guide
SBOOST User Guide 2
Version 1.4 February 2012 © Copyright 2012SPROG DCC
Introduction
SBOOST is a DCC booster designed primarily intended for use with the
SPROG II, but also useable with other DCC systems, to boost the track
output current for driving a larger layout.
Requirements
Regulated DC Power Supply 12 –20V, 3A
Features
Opto-isolated DCC input for electrical isolation between the layout and
the command station
DCC activity LED shows reception of valid DCC input
Power LED flashes when programming track power is live
Specification/Operating Conditions
Parameter
Minimum
Typical
Maximum
Units
DC Input supply
voltage
12V
20V
V
Vin supply current
2.6
Note 1
A
Output Load –
Operating Layout
2.5
A
Auto reverse
detection delay
1.2
ms
Overload detection
delay
3.2
ms
Overload cutout
delay
410
ms
1. The current capacity of the power supply must be greater than the
2.5A current limit of the SBOOST. A 3A power supply is
recommended.
2. The DCC track voltage will be slightly less than the power supply
voltage.
SBOOST User Guide 3
Version 1.4 February 2012 © Copyright 2012SPROG DCC
DCC Parameters
Minimum
Typical
Maximum
Units
DCC signal input
voltage
7
18
V
DCC signal input
current
10
Note 3
mA
DCC signal input
current
16.5
Note 4
mA
DCC Input –Track
Output Delay
1.6
µs
3. Vin 12V
4. Vin 18V
LEDs
Track LED
Off
Track power off
Flashing Moderately Quick
Track power on
Flashing quickly
Short circuit
DCC LED
Flashing slowly
No DCC signal
Flashing Quickly
Valid DCC Signal
Installation
The following steps are required to install SBOOST before you can use it for
the first time:
Connect to the Power Supply
Connect to the Layout
Connect to the Command Station
Connect to the Power Supply
Power supplies sold by SPROG DCC are supplied with a circular DC jack
plug. This should be removed to allow connection to the pluggable terminal
block:
Cut off the DC plug
Separate the two conductors for about 3cm
SBOOST User Guide 4
Version 1.4 February 2012 © Copyright 2012SPROG DCC
Strip 6-8mm of insulation from each conductor and twist the copper
cores of each conductor together
Insert the conductor marked with a white stripe in the +V terminal and
tighten the screw
Insert the other conductor in the 0V terminal and tighten the screw
SBOOST is protected against reverse polarity connection of the power
supply, but will not work unless the polarity is correct.
Connect to the Layout
Connect the SBOOST to the track using the track terminals “Tr A” and “Tr B”
of the pluggable terminal block.
Connect to the Command Station
Connection to a SPROG II (version 2 and earlier)
The pluggable terminal block is arranged to allow a straight forward
connection to a SPROG II for both the DCC signal and to supply power to the
SPROG II (See below), see the picture below.
Connect the SBOOST DCC inputs “In A” and “In B” to the SPROG II track
outputs.
Powering a SPROG II (all versions)
There are two considerations to be taken into account when powering an
SBOOST and a SPROG II from the same power supply.
The electrical isolation between the layout and command station (i.e. SPROG
II) will no longer be effective.
The SPROG II has a lower maximum supply voltage of 15V, compared to the
SBOOST maximum of 20V. When using an SBOOST with a supply voltage
greater than 15V special care must be taken. For SBOOST supply voltages
above 17V, a separate power source, of the correct voltage, should be used
SBOOST User Guide 5
Version 1.4 February 2012 © Copyright 2012SPROG DCC
for the SPROG II. For SBOOST supply voltages in the range 15 –17V you
can use a separate power supply or insert a string of 3 1N4001 (or similar)
diodes in series with the +V connection to drop the voltage slightly.
Connect the SBOOST +V output to the SPROG II +V input.
Connect the SBOOST 0V output to the SPROG II 0 input.
Connection to a SPROG 3
Follow the connection instructions for SPROG II. The SPROG 3 is rated for
the same maximum voltage as the SBOOST and can always use the same
power supply.
If electrical isolation is required between the layout and SPROG 3 then a
separate, isolated, power supply must be used.
Connection to Other Command Stations
TBD
Multiple Power Districts Using SBOOST
If more than one SBOOST is to be connected between the command station
(e.g. one of the SPROG family) and the layout, to give multiple power
districts, then care must be taken with both the DCC input connections and
the track connections to ensure the same polarity at each SBOOST.
Connect all of the SBOOST “In A” terminals together and connect to one
output of the command station.
Connect all of the SBOOST “In B” terminals together and connect to the other
output of the command station.
Connect the “Tr A” and “Tr B” outputs to the layout in a consistent manner in
each power district. E.g. connect “Tr A” to the left rail in each power district
and connect “Tr B” to the right rail in each power district.
BOTH rails MUST be gapped between power districts. The SBOOST track
outputs must only be connected to their own power district, i.e., there must be
NO common wiring between power districts.
If a single power supply is used to power more than one SBOOST it must be
rated to supply the maximum current to all SBOOST simultaneously. E.g. for
two SBOOST the power supply must be rated at greater than 5 Amps.
If separate power supplies are used to power multiple SBOOST then they
should all be of the same type and voltage rating. The 0V connections of all
SBOOST User Guide 6
Version 1.4 February 2012 © Copyright 2012SPROG DCC
the SBOOST must be connected together. This is sometimes referred to as a
booster “home ground” connection.
Example 1
SPROG 3 (or SPROG II) and SBOOST with common power supply.
Using a SPROG 3 and SBOOST in this way is not recommended.
A short circuit in the SPROG 3 power zone will affect the DCC signal to the
SBOOST.
The power supply must be able to supply the full rated current (i.e., at least 5
Amp for SPROG 3 plus SBOOST).
Power districts must be separated by isolation gaps in both rails.
Isolation Gap
Power
SBOOST User Guide 7
Version 1.4 February 2012 © Copyright 2012SPROG DCC
Example 2
SPROG 3 and SBOOST with separate power supplies.
Using a SPROG 3 and SBOOST in this way is not recommended.
A short circuit in the SPROG 3 power zone will affect the DCC signal to the
SBOOST.
Each power supply should be the same voltage.
Each power supply must be able to supply the full rated current, at least 2.5
Amp.
A common ground connection is required between the power supplies.
Power districts must be separated by isolation gaps in both rails.
Isolation Gap
Power
Power
SBOOST User Guide 8
Version 1.4 February 2012 © Copyright 2012SPROG DCC
Example 3
SPROG 3 (or SPROG II) driving multiple SBOOST with common power
supply.
The power supply must be able to supply the full rated current (e.g., at least 5
Amp for 2 x SBOOST).
Power districts must be separated by isolation gaps in both rails.
The SPROG can be powered from one of the SBOOST
Isolation Gap
Power
Power
To further SBOOST
SBOOST User Guide 9
Version 1.4 February 2012 © Copyright 2012SPROG DCC
Example 4
SPROG 3 (or SPROG II) driving multiple SBOOST with separate power
supplies.
Each power supply should be the same voltage.
Each power supply must be able to supply the full rated current, i.e. at least
2.5 Amp.
A common ground connection is required between the power supplies.
Power districts must be separated by isolation gaps in both rails.
The SPROG can be powered from one of the SBOOST.
Isolation Gap
Power
Power
To further SBOOST
SBOOST User Guide 10
Version 1.4 February 2012 © Copyright 2012SPROG DCC
Auto-reverse Operation
The SBOOST can be configured for auto reverse operation, e.g., to supply
power to a reverse loop or wye formation as a separate power district.
To enable or disable auto-reverse operation you must open the casing of the
SBOOST and fit or remove a jumper link.
To open the casing, prize the two halves apart by inserting a small flat bladed
screwdriver in the slots and twisting gently, as shown below.
Identify the location for the jumper link near the DCC input connector, see
below.
Table des matières
Autres manuels Sprog Extenseur
