Spotlight PIC HS Manuel utilisateur

I - DESCRIPTION OF THE PROJECTOR

II - GENERAL

III - INSTALLATION

WARNING!

ALWAYS

CONNECT THE

PROJECTOR TO A

MAIN WHICH IS

PROTECTED BY A

SUITABLE

ELECTRIC FUSE

SELECTED

ACCORDING TO

THE

INSTRUCTIONS

1. Suspension clamp

2. Accessory guides

3. Accessory locking spring

4. Lever handle for adjusting inclination of projector

5. Lamp holder tray access knob

6. Lamp position adjustment knob

7. Screws to adjustlamp

8. Safety chain anchorage clamp

9. Wing nut for locking and adjusting projector focus

10. Lever handle for lens adjustment (Zoom)

11. N° 4 levers for flaps adjustment

The projector you have bought satisfies directives

73/23/EEC as it complies with standards EN 60598-1

and EN 60598-2-17.

!model

!maximum supply voltage in V

!maximum power of the projector in W

!the index of protection IP

!maximum temperature of the environment admitted

in °C

!maximum temperature of the projector body in °C

!minimum distance from any inflammable surface

!information to find the position 0° of the projector:

when the tip of the arrow points upwards

!maximum angle of inclination upwards and

downwards. These limits, imposed by the lamp

manufacturer, should not be exceeded as they

would reduce the projector’s useful life or lead

to its deterioration.

The projector can be either suspended or mounted on a

stand.

WARNING!

DO NOT INSTALL THE PROJECTOR ON SURFACES

WHICH ARE USUALLY INFLAMMABLE.

The minimum distance at which the projector must be kept

from easily inflammable surfaces is indicated on the label.

The safety norms estimate that a metal wire screen be

mounted on the front of the projector to prevent any large

glass fragments from falling if the projector breaks.

WARNING!

REPLACE THE LAMP AND/OR LENS IF VISIBLY

DAMAGED.

For safety reasons always use the safety chain between the

projector and the suspension truss.

3.1 - Accessories

The accessories estimated for this projector are listed in the

price list and can be mounted by inserting into guides 2.

Followspot/steel

Line

Mod.PIC HS

IV - CHANGING THE LAMP

Your projector has been designed for a maximum

voltage of 230 V.

The power cable complies with standards CEI 20-22.

However one must make sure that the ground is always

connected.

Using the side handle 4 it is possible to release the

projector when it is locked in a certain position and

change its inclination. The same can be done as

regards its rotation with respect to the vertical axis by

loosening wing nut 9. The zoom is adjusted with levers

10, by widening or narrowing the beam of light. The

beam of light can be cut with the four flaps 11 to obtain

special effects.

VII - CLEANING

VI - FOCUS AND REGULATIONS

VIII - MAINTENANCE

The projector must be serviced at least once a year to

check the integrity of its electrical and mechanical parts.

. .

V - ELETTRICAL CONNECTIONS

For safety reasons always disconnect the projector

from the mains before opening it to change the lamp.

Open the projector latch by using knob 5. Insert the

lamp into the socket taking care not to touch the glass.

Since the new lamp may have a different centre of light,

it may be centred with knob 7 and the 2 screws 13.

For utmost projector performance, both the lens and

the reflector must be kept as clean as possible. To do

so, after disconnecting the projector from the mains,

open it and clean both the lens and reflector with a soft

cloth dampened with alcohol.

Followspot/steel

Line

Mod.PIC HS

Table des matières

Autres manuels Spotlight Matériel de DJ

Spotlight

Spotlight mini Profile LW Series Manuel utilisateur

Spotlight

Spotlight COM 05 PC Manuel utilisateur

Spotlight

Spotlight FollowLED 450 CW DMX Manuel utilisateur

Spotlight

Spotlight Vedette 12 H CC Manuel utilisateur

Spotlight

Spotlight Fresnel LED Hyperion 300 6C Manuel utilisateur

Spotlight

Spotlight FresneLED 450 RGBW Manuel utilisateur

Spotlight

Spotlight Vedette 2500 compact Manuel utilisateur

Spotlight

Spotlight FresneLED C100 DMX Series Manuel utilisateur

Spotlight

Spotlight FN LED C100 CW DMX Manuel utilisateur

Spotlight

Spotlight FresneLED 200 DMX Manuel utilisateur

Spotlight

Spotlight ProfiLED 50 ZS DMX Manuel utilisateur

Spotlight

Spotlight ProfiLED 450 RGBW DMX Manuel utilisateur

Spotlight

Spotlight PR LED 150 ZSRGBWDMX Manuel utilisateur

Spotlight

Spotlight PR LED 250ZS TW DMX Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur