Splash SuperPools SuperPool Manuel utilisateur
User’s Guide
©2003-Splash Superpools Ltd.
Splash SuperPools, LLC • 3912 East Progress • North Little Rock,AR USA72114
(800)92-SPLASH • http://www.splashpools.com
WARNING:
Shallow water! Never jump or dive into a
Splash SuperPool; serious bodily injury could occur.
If you have any questions on the assembly of your
Splash SuperPool or Splash OmegaPool, please call
your local Splash SuperPools dealer.
©2003-Splash Superpools Ltd.
Congratulations on the purchase of your Splash
SuperPool!
A few notes prior to assembly. . .
Be sure that you have an area that is smooth, level and 4 feet larger
than the pool to assemble your SuperPool. Remove all sticks, rocks, and any
sharp objects. Remove and cap off any sprinkler heads, fill voids, depres-
sions, or hollows with dirt or sand. Any areas filled with dirt or sand must
be compacted prior to installation of your pool.
If you are installing your SuperPool on dirt, sand, or grass, we recom-
mend that you place a plastic sheet or foam pad between your pool and the
ground.
Splash SuperPools are portable swimming pools, and as a result, most
localities do not require the homeowner to obtain any permits. However, it
is the homeowner’s responsibility to meet all applicable safety/health codes
and zoning regulations.
WARNING: NEVER INSTALL YOUR SUPERPOOL
UNDERNEATH HIGH VOLTAGE POWER LINES —
SERIOUS INJURY OR DEATH COULD RESULT.
WARNING: SHALLOW WATER! NEVER JUMP OR
DIVE INTO A SPLASH SUPERPOOL — SERIOUS
BODILY INJURY COULD OCCUR!
3©2003-Splash Superpools Ltd.
Congratulations! .................................................................................... 3
SuperPool Parts List.............................................................................. 5
Getting Started ...................................................................................... 6
Installing Circulation System ................................................................10
Adding Optional Skimmer.....................................................................12
Filling and Starting Your Pool ...............................................................13
Omega Parts List..................................................................................14
Omega Assembly Instructions..............................................................15
Vacuuming Your Splash SuperPool ......................................................20
Cleaning Filter and Pump Basket.........................................................19
Winterizing Your Splash SuperPool......................................................21
Ladder Assembly..................................................................................22
SplashLadder ....................................................................................23
Omega Ladder ..................................................................................29
Table of Contents
Never leave children or inexperienced
swimmers alone in any pool.
©2003-Splash Superpools Ltd.
5
Splash SuperPools Parts List
A. Male Top Rail End Piece
B. Middle Top Rail Section
C.Female Top Rail End Piece
D.Leg
E. SplashBlox
F. Stainless Steel Ring
G Connecting Pin
H.Wall Fittings
I. Hose w/Threaded Nipple/Gasket
J. Floating Skimmer Weir
K. Skimmer Hold Down Fitting
L. Skimmer Basket
M.Skimmer
N.Vacuum Adapter Plate
O.Ball Valve
P. Eyeball Fitting
©2003-Splash Superpools Ltd.
C
BF
G
E
J
K
I
A
O
L
N
M
P
D
H
Getting Started
1. Unfold your pool on your selected and prepared site. Locate the pre-punched plumbing holes in one of the
short walls of the pool and position them where you want your pump and filter to be located. CAUTION:
Electrical outlet will require GFI (ground fault interruption) protection. Hint: Your SuperPool skimmer can be
even more effective if located at the prevailing “down wind” end of the pool. WARNING: Make sure you do not
install your pool under electrical lines.
2. Insert the galvanized steel Top Rails into the seamed pockets at the top edge of the pool.There is a slot located
in each corner that will accept the Top Rails. Insert one Female End Piece (C) into the sleeve; continue adding
Middle Top Rail Sections (B) as you slide the rail into place, until the necessary length is obtained. Finish each
wall with a Male End Piece (A). Once all top rails are inserted, align pre-punched holes in pool with holes in Top
Rail.
Hints: Set rails out around the perimeter of the pool before you begin assembly.
Insert rails into the long sides of the pool first. As you insert each piece of the rail and begin to slide, it helps to pull
and tighten the white sleeve to avoid hitting wrinkles. Be careful not to scrape the ends of the railing along the
pool material.
On hot days the rails may “grab” the sleeve as you are inserting them. This can be prevented by wetting the top
rails with a garden hose as you insert them.
6©2003-Splash Superpools Ltd.
7
4. Insert the Leg into the Top Rail as in Item 2A, spreading the Leg apart until it slides into the holes. When all the
buttresses are inserted, the pool will look like Item 2B. Finally, connect Leg with Connecting Pin to the pool
buttress strap as in Item 3.
3.
Aboveisan illustration of the assembly oftheSplash SuperPoolLegs.Slidethe two Stainless SteelRingsonto the
Leg. Continue this process until you have assembled all the Buttress Legs.
Item 2A Item 2B
D
F
Item 3
©2003-Splash Superpools Ltd.
5.
Putone person inside thepool to hold the wallat theTop Rail.
Insertthe Connecting Pins (G), toconnect the pool
straps to the Stainless Steel Rings. Repeat this process with all four walls.
Note: At this stage, all four walls will be leaning inward; this is normal. They will automatically move to their
proper positions once the pool is filled with water.
6. Gently pull buttress straps away from the center of the pool to insure a wrinkle-free installation.
WARNING: Shallow water! Never jump or dive into a
Splash SuperPool; serious bodily injury could occur.
7. Position the short wall Top Rails so they are leaning over and on top of the long wall Top Rails.
8©2003-Splash Superpools Ltd.
8. There must be solid support under each Buttress Leg because, when the pool is filled, the weight on each Leg
will be approximately 2,000 pounds. If the pool is on a surface other than concrete, the recommended method
of support is to utilize the included SplashBlox (grey footblock). Place the SplashBlox under the Leg, placing
the Leg into the recess on the top of the SplashBlox. The SplashBlox is designed to provide the proper support
to the Leg to move as the pool fills.
Note: The Buttress Leg must be placed in the center of the support.
9
9. In the positioning of your Splash SuperPool, make sure that all Buttress Leg tubes are still inserted properly into
the Top Rail. Do this by placing your hand on the Top Rail where the individual Leg tubes insert, and feel with
thumb and fingers. If you find that a Leg has been dislodged, re-insert it into the Top Rail.
WARNING: Shallow water! Never jump or dive into a
Splash SuperPool; serious bodily injury could occur.
©2003-Splash Superpools Ltd.
10
Installing the Circulation System
1. Wall Fitting Installation — Install the two Wall Fittings (H) at the locations labeled “intake” and “return”. Also
install the Skimmer Hold Down Fitting (K) in its marked location. Each of these three fittings has two rubber and
one paper gasket. These should be positioned as in the diagram above. No thread sealer or Teflon tape is
required.
2. Skimmer Installation — From inside the pool, screw hose from bottom of Skimmer (M) into the Intake Wall
Fitting, and hand- tighten. No Teflon tape is required. Note: use soapy water to slide hose onto bottom of
skimmer. Next, screw the short hose from the side of the Skimmer into the Skimmer Hold Down Fitting (K).
Again, hand-tighten. Screw the Eyeball Fitting (P) into the Return Wall Fitting. *Note that “hose side” is im-
printed on the 90 Degree Fitting for your convenience. Now is when the person inside the pool will want to get
out.
3. Pump and Filter Installation — Please refer to the directions supplied by the manufacturer of your pump and
filter.
NOTE: The 17' x 29.5' SuperPool has holes for an optional extra skimmer. If you choose not to use an extra
skimmer, use the supplied Wall Fittings and plugs to seal holes.
WARNING:
The circulation system produces
very strong suction. NEVER lay on or insert
body parts into the skimmer. Always turn off
pump before working on the skimmer.
See (L) on page 2 for Skimmer
Hold Down assembly diagram.
M
Skimmer
K
Hold
Down
H
Intake
Pool
Liner
Rubber
Gasket
Rubber
Gasket
Paper
Gasket
PEyeball Fitting
*Hose Side
K
Hold Down
H
Intake
H
Return
©2003-Splash Superpools Ltd.
Table des matières
Autres manuels Splash SuperPools Piscine
