SpeakerCraft DT8 ZERO Manuel utilisateur

In our attempt to constantly improve our products, features and specifications are subject to change without notice.

Page 4 DT8 Zero Owner’s Manual

940 Columbia Ave., Riverside CA 92507-4492

(800) 448-0976 Fax (951) 787-8747

www.speakercraft.com LIT75800

Should you have any questions regarding this, or any other SpeakerCraft product, please call our toll-free Service Hotline at

1-800-448-0976. We are available to assist you every weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.

SpeakerCraft offers a variety of accessories to make your installation of these speakers and other SpeakerCraft products easy, economical,

and professional. Contact your authorized SpeakerCraft Dealer for more information.

SPEAKER SPECIFICATIONS

System Description:

High Frequency Drivers:

Low Frequency Driver:

Impedance:

Frequency Adjustments:

Efficiency:

Frequency Response:

Power Recommendations:

Diameter x Depth:

Cut-Out Diameter:

PRINTER'S INSTRUCTIONS:

INSTR,INSTL,AIM DT • INK: BLACK • MATERIAL: 70LB GLOSS PAPER • SIZE: 8.500" X 11.000" • SCALE: 1-1 • FOLDING: HALF FOLD

DT8 Zero

Two tweeters mounted onto a

dual voice coil woofer

Dual 1" Resin coated Silk Dome

Tweeters

8" Polypropylene Cone

Woofer with Dual Voice Coil

and Rubber Surround

8Ω

None

91dB 1w/1m

50Hz - 20kHz

80 watts (undistorted)

113⁄8" x 4"

(288.925mm x 101.600mm)

93⁄4"

(247.650mm)

OWNER’S MANUAL

SPEAKER PLACEMENT

Before installing your speaker, you should consider the placement carefully, taking into account the location of

electrical, plumbing and other fixtures. Contact your dealer for assistance if you are not sure of the best loca-

tion in your particular room environment.

Ceiling Placement: When placing your speaker into the ceiling, it should ideally be located above the pri-

mary listening area. The DT is intended to be used as a single stereo speaker in small listening environments,

walk-in closets, laundry rooms, bath rooms etc. In a large area, it may be necessary to place additional speak-

ers throughout the room to get the optimal effect.

MOUNTING SURFACE PREPARATION

New Construction - Unfinished Ceilings

A New Construction Bracket, SpeakerCraft part number BKT90611 (available from your dealer), may be

installed prior to drywall application across joists (up to 24" on-center) where a speaker will be located.

Insulation material should be in place prior to installing drywall. After the hole is cut and the drywall is

installed, the speaker can then be easily installed following the instructions for mounting under “Finished

Ceilings” below.

Finished Ceilings

Prior to the actual installation of the speaker, it will be necessary to run cables to the speaker location. See

your dealer for more information on cable installation. After the cable has been properly installed, you are

ready to mount the speaker. Following the simple steps listed below will result in a professional looking instal-

lation:

1. Determine the best area to mount your speaker. This area of the ceiling should be free of obstructions such

as electrical conduit, HVAC ducts, or water lines. This can best be determined by noting the placement of

fixtures and gaining access to an attic or crawl space for further analysis of the location of such obstacles.

2. Find the joists nearest the desired speaker mounting location. We highly recommend using a good stud-

finder tool for this procedure. If you are lining up the speaker to some other object or molding in the

room, make sure you consider the size of the baffle flange which extends beyond the mounting hole.

3. Mark the hole. A punch out template for setting the hole is provided in the box. Position the template in

the desired position and pencil an outline on the ceiling.

4. Cutting the hole. CAUTION: This is the most important part

of the entire installation. If you are not certain whether any

obstructions exist behind the desired mounting area, you

should start by cutting a small hole in the center of your

penciled mounting hole with a drywall saw, cutting at a 45º

angle towards the inside of the hole. (See Diagram 1)

Cutting the small hole at this angle will make drywall repair

much easier, using the piece cut out. Once you have deter-

mined that there aren’t any obstructions in your desired

mounting location, start cutting the finished hole at a 90º

angle to the ceiling’s surface.

DT8 Zero

Single Stereo Speakers

PRINTER'S INSTRUCTIONS:

INSTR,INSTL,AIM DT • INK: BLACK • MATERIAL: 70LB GLOSS PAPER • SIZE: 8.500" X 11.000" • SCALE: 1-1 • FOLDING: HALF FOLD

Diagram 1

Page 2 Eazy6 Owner’s Manual

Page 2 DT8 Zero Owner’s Manual

5. Add insulation. If the area in the ceiling is not already insulated, add an

adequate amount insulation material to loosely cover the back of the

speaker. If the insulation material used is faced with foil or paper, position

the foil or paper away from the speaker.

SPEAKER INSTALLATION

The unique integral four foot mounting system incorporated into your AIM DT

speaker allows for a quick installation by following these easy steps.

1. Remove the grille. It may be necessary to push one or two of the mount-

ing screws, and its attached foot, towards the baffle and against the inside

surface of the grille to force the grille out of its retaining groove.

2. Attach the speaker cable (observing the proper polarity with your amplifier,

+ to + and - to -). Either channel may be attached to either terminal set,

however, be sure that polarity (+ and -) is correct on each channel or the

performance of the speaker will be seriously affected, as one channel will

cancel out the other. (See Diagram 2)

3. Make sure the mounting feet are turned inward to clear the opening,

and insert the speaker into the ceiling. Position the speaker into the hole.

Note: The flange of the speaker is designed to flex and conform to any

small imperfections in the ceiling’s surface. Tighten the four screws on the

front of the baffle only enough to make the flange become snug against

the ceiling. As you tighten the screws, the feet will automatically flip into

an outward position thereby clamping the drywall between the feet and

the flange. (See Diagram 3)

CAUTION: Over tightening may warp the baffle, crack the ceiling, cause

the flange to distort, and make the grille difficult to install.

4. Push the grille firmly into the slot in the speaker baffle.

SPEAKER ADJUSTMENT

Adjusting the Pivoting Tweeters

Once the woofer is positioned, further refinement can be made by pointing

the tweeter towards the listener. Gently pivot the tweeter to point it in the

desired direction (See Diagram 4).

PAINTING THE SPEAKER

If you plan to paint your speaker, we recommend that it be done prior to

installation. If you plan to paint your speaker sometime in the future, it is

best to remove it by simply reversing the steps for “Speaker Installation” listed

above. If it is necessary to paint the speaker while it is still in the ceiling, the

paint mask provided in the carton must be installed in place of the grille while

the flange is being painted with the ceiling. The grille can also be painted,

however, great care should be taken not to clog the holes as this will greatly

reduce the sound quality of the speaker. SpeakerCraft recommends only light

spray painting using 5 parts thinning agent to 1 part paint. Do not paint the

grille while it is attached to the speaker.

PRINTER'S INSTRUCTIONS:

INSTR,INSTL,6.XDT • LINEINSTR,INSTL,AIM DT • INK: BLACK • MATERIAL: 70LB GLOSS PAPER • SIZE: 8.500" X 11.000" • SCALE: 1-1 • FOLDING: HALF FOLD

Diagram 3

Diagram 2

Diagram 4

Pivot the Tweeter by gently

pushing on the sides

DT8 Zero Owner’s Manual Page 3

LIMITED LIFETIME WARRANTY

SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and

workmanship, provided the speaker was purchased from a SpeakerCraft Authorized Dealer.

Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom

they were purchased, or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments

will be refused. It is preferable to ship this product in the original shipping container to lessen the chance of transit damage. In any case,

the risk or loss or damage in transit is to be borne by the purchaser. If, upon examination at the Factory or SpeakerCraft Authorized Dealer,

it is determined that the unit was defective in materials or workmanship at any time during this warranty period, SpeakerCraft or the

SpeakerCraft Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below. If this

model is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option may replace the unit with a current model

of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If

mounting surface modification is required, SpeakerCraft assumes no responsibility or liability for such modification. All replaced parts and

product become the property of SpeakerCraft Inc. Products replaced or repaired under this warranty will be returned to the original retail

purchaser, within a reasonable time, freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate pack-

ing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification

of the product which has not been authorized or approved by SpeakerCraft. This Warranty also excludes normal cosmetic deterioration

caused by environmental conditions. This Warranty will be void if the Serial Number on the product has been removed, tampered with or

defaced.

This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the

purchaser’s sole remedy shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or con-

sequential damages arising out of the use or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer

has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow

the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.

All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow

limitation on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation

does not apply.

PRINTER'S INSTRUCTIONS:

INSTR,INSTL,6.XDT • LINEINSTR,INSTL,AIM DT • INK: BLACK • MATERIAL: 70LB GLOSS PAPER • SIZE: 8.500" X 11.000" • SCALE: 1-1 • FOLDING: HALF FOLD

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SpeakerCraft Intervenants

SpeakerCraft

SpeakerCraft ATX100 Manuel utilisateur

SpeakerCraft

SpeakerCraft CRS8 One Manuel utilisateur

SpeakerCraft

SpeakerCraft 600 Manuel utilisateur

SpeakerCraft

SpeakerCraft 8.1DT Manuel utilisateur

SpeakerCraft

SpeakerCraft CS3 Manuel utilisateur

SpeakerCraft

SpeakerCraft AIM8 One Manuel utilisateur

SpeakerCraft

SpeakerCraft AIM LCR3 Five Manuel utilisateur

SpeakerCraft

SpeakerCraft AccuFit IW7 Three Manuel utilisateur

SpeakerCraft

SpeakerCraft MT6 One Manuel utilisateur

SpeakerCraft

SpeakerCraft Ruckus 8 Manuel utilisateur

SpeakerCraft

SpeakerCraft AIM7 Two Manuel utilisateur

SpeakerCraft

SpeakerCraft AIM7 FIVE Manuel utilisateur

SpeakerCraft

SpeakerCraft CRS8 One Manuel utilisateur

SpeakerCraft

SpeakerCraft Ruckus 8 Sub System Manuel utilisateur

SpeakerCraft

SpeakerCraft NEAT! LCR Five Manuel utilisateur

SpeakerCraft

SpeakerCraft SLS One Manuel utilisateur

SpeakerCraft

SpeakerCraft STARLET 4 Manuel utilisateur

SpeakerCraft

SpeakerCraft Ruckus 8 Manuel utilisateur

SpeakerCraft

SpeakerCraft AccuFit DT7 Three Manuel utilisateur

SpeakerCraft

SpeakerCraft CRS6 Zero Manuel utilisateur

SpeakerCraft

SpeakerCraft WeatherCraft WS950 Manuel utilisateur

SpeakerCraft

SpeakerCraft AIM7 MT Three Manuel utilisateur

SpeakerCraft

SpeakerCraft OE5 Three Manuel

SpeakerCraft

SpeakerCraft CRS6 Zero Manuel

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur