SpeakerCraft SmartPath IRE-1.0 Manuel de service

DESCRIPTION

The IRE-1.0 represents the highest level in sophistication for attachable

IR Emitters. It features a unique EZ-Docker™port that permits instant

removal of the emitter when rearranging or servicing components.

An improved adhesive reduces callbacks for reattachment of “fallen

emitters”. The case may also be taken apart so that the tiny internal

emitter can be placed inside a component, when desired. High IR

output from the top curved surface allows emitter to be mounted on

a nearby surface, below, above or on a cabinet door, rather than

directly on the sensor of the unit where conditions

permit.

ATTACHMENT

First, locate the component’s IR sensor window (see Note 1) and

thoroughly clean it of any fingerprints or other greasy substances.

The EZ-Docker™port has a clear adhesive layer on its bottom surface.

Peel the protective layer off,

exposing the adhesive.

Orient the port vertical (see

Fig. 2) and press it over the

center of the component’s

sensor window. Press and

hold for several seconds to

ensure maximum contact

of the adhesive.

Slide the emitter from the

top down, into the EZ-

Docker™port. You should

feel it “snap” into place. (To

remove the emitter at any

time, simply push upward

until it “pops” out).

IRE-1.0

Emitter

8 FT 9/16"

7/16"

3.5mm

mini plug

1/4"

Side View

Emitter

Wire Lead

Docking

Port

Clear Adhesive Tape

(See Note 3)

Top View

NOTE: White striped side is positive ( +)

(–)

(+)

Emitter slides into

Docking Port

Fig. 1

Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft

Terminator or other source of IR (see Fig. 3).

CAUTION: Do not plug into an emitter jack that is set to Blaster

Power (BL ON) or to the HIGH OUT of other connecting blocks.

To do so will smoke the emitters!!

Note 1: If you have difficulty finding the component’s IR sensor, try

using a flashlight. Sometimes the owner’s manual is helpful. You may

need to contact the manufacturer direct.

Note 2: You may also attach the emitter without the EZ-Docker™port.

Use one of the spare adhesives (included) applying it directly to the

bottom surface of the IRE-1.0 shell.

Note 3: If you need to remove the EZ-Docker™port or emitter previ-

ously stuck to a component’s surface, use a fresh adhesive (included)

before reattaching.

Note 4: The emitter shell and EZ-Docker™port, though dark in

appearance, are transparent to Infrared. This allows IR commands to

pass through them, permitting local hand held remote control as

well as through the IRE-1.0.

IR Controlled Components

IR sensor

window

Docking Port

IRE-1.0 attached to

IR sensor window

2) Slide IRE-1.0 Emitter

end into docking port

1) Attach IRE-1.0 Docking Port

to IR sensor window with adhesive pad

Fig. 2

IRE-1.0

IR Emitter

SpeakerCraft

SmartPath™

INSTALLATION INSTRUCTIONS

LIT03100 02/02

ELT03100

IR Controlled Components

IR Sensor

Window

Fig. 5a

IRE-1.0 attached directly

to IR sensor window

Cabinet Door

Fig. 5b

IRE-1.0 attached to inside of

cabinet door directly opposite

IR sensor window

IRE-1.0 attached to shelf directly

below or above IR sensor window

Fig. 5c & d

Fig. 5

Low

output side

toward IR

sensor

Connecting

lead

Emitter

Shell

High

output

side

Internal

IR Emitter

In others, it may be necessary to remove the internal emitter from its

shell so that it will fit in tiny chassis places. In this case, use the thin

edge of a knife to carefully pry the lower cover from the shell of the

emitter. Gently ease the tiny emitter and lead from it’s nest within the

shell. Use heat shrink tubing, or other insulating means, to prevent

shorting of the exposed leads.

Fig. 4

SpeakerCraft

SpeakerCraft •1650 Seventh Street, Riverside, CA 92507 •Phone 1-800-448-0976 •Fax 888-599-9059

www.speakercraft.com

LIMITED 5-YEAR WARRANTY

SpeakerCraft warrants this product to be free of defects in materials or

workmanship. This extends for five years from the date of purchase

by the original consumer. Any products returned to SpeakerCraft and

found to be defective by SpeakerCraft within the warranty period will

be repaired or replaced, at SpeakerCraft’s option, at no charge.

SpeakerCraft will not be responsible for the actual cost of installation

or removal of the product, nor for any incidental or consequential

damages. Some states do not allow the exclusion or limitation of inci-

dental or consequential damages, so the above limitation may not

apply to you. This warranty gives you specific legal rights. You may

have additional legal rights that vary from state to state.

Other Emitter Placements

Since the IRE-1.0 has high output from it’s curved top (See Fig. 4),

you may attach it to other surfaces nearby, if the installation permits.

(See Fig. 5)

Use the higher power setting (NOT Blaster Power) on the connecting

block or terminator, if so provided.

Some installers like the option of placing the emitter completely inside

a component, as near as possible to the IR sensor, for a clean external

appearance. In some cases, the whole emitter can be so placed.

TYPICAL INSTALLATION

Satellite Receiver

PS-1.0

IRE-1.0

Emitter

IRE-1.0

Emitter

VCR

A/V Receiver

Hand Held

Remote

IRC-3.0

Emitter

IR Sensor

Window

AT-1.0

Amplified Terminator

Unit

Power Supply

120V AC

(unswitched)

Shelf Top

IR Receiver

Fig. 3

Table des matières

Autres manuels SpeakerCraft Télécommande

SpeakerCraft

SpeakerCraft VSI60 Manuel utilisateur

SpeakerCraft

SpeakerCraft VSI45 Manuel utilisateur

SpeakerCraft

SpeakerCraft TIME8 Manuel utilisateur

SpeakerCraft

SpeakerCraft EazyR-2 Instructions d'installation et d'utilisation

SpeakerCraft

SpeakerCraft VWS60 Manuel utilisateur

SpeakerCraft

SpeakerCraft VSR-100 Manuel utilisateur

SpeakerCraft

SpeakerCraft SmartPath IRE-4.0 Manuel utilisateur

SpeakerCraft

SpeakerCraft VBX Tabletop Manuel utilisateur

SpeakerCraft

SpeakerCraft VCR120 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation