SPE MS230 Manuel utilisateur
MS230 - 2
MULTISTRIPPER
Operating Manual
This manual is provided to persons purchasing an
SPE machine and may not be reproduced in part or full
without written permission of
SPE International Ltd.
This manual provides the basic information required
and is only to be used as a guideline.
The SPE machines are manufactured and covered by
SPE design registrations granted and pending.
SPE International Ltd reserves the right to alter the
equipment design and specification as required
without notice.
The SPE product range is subject to amendment and
improvement as a result of on going research
Honeyholes Lane, Dunholme, Lincoln LN2 3SU, England
Tel: +44 (0) 1673 860709 Fax: +44 (0) 1673 861119
Email: sales@spe-int.com
VERSION 1.03
MS230-2
MULTISTRIPPER
Operating Manual
MS230 MULTISTRIPPER
OPERATING MANUAL
This manual covers to the best of our knowledge, the operation and maintenance of the
MS230 Multistripper. Before operation of the equipment the manual should be read and
understood by the operator. The safety regulations must be followed at all times. Service of
electrical components should be carried out by authorised personnel. Failure to follow these
instructions could result in damage to the machine and/or serious personal injury or death.
WARNING
Failure to follow these instructions may result in serious personal injury or death. SPE
disclaims all responsibility for damage to persons or objects arising as a consequence of
incorrect handling of the machine and failure to inspect the machine fordamageorotherfaults
that may influence the operation prior to starting work.
MS230-2
MULTISTRIPPER
Operating Manual
INDEX
Page No
1 Starting Work
Electrical Instructions
2 Maintenance
Blade Change
Blade Angle
Basic Maintenance Checklist
3 Safety
4 Spare Parts Breakdown
5 Body Components
6 Operational Parts
7 Electrical Listing
8 Wiring Diagram
9 Specifications
10 Noise/Vibration Assessment
11 Warranty
12 Declaration of Conformity
13 Conditions of Sale
MS230-2
MULTISTRIPPER
Operating Manual
STARTING WORK
1) Check the condition of the blade assembly
2) Check all bolts and nuts for tightness
3) Check all leads for damage where applicable
4) Before starting the machine ensure that the blade is clear of any obstructions
5) Adjust the handlebar to a comfortable height and position.
6) Adjust the blade angle to a suitable setting –See blade angle (page 2)
7) Start the motor by turning the switch to the on position.
NOTE: If removing sheet vinyl or carpet cut the material into strips with a knife at
approximately the width of the MS230 blade.
ELECTRICAL INSTRUCTIONS
Extension cables must be no less than 2.5 mm (normal length 30 metres)
All cables should be fully uncoiled and never left wrapped around cable reels or tied in loops.
An RCD unit must be used with the MS230 240v.
1
MS230-2
MULTISTRIPPER
Operating Manual
MAINTENANCE
AFTER USE:
- Clean the machine to remove all the build up of dust and surface residue. If using a hose
pipe or pressure washer take care that water is not directed onto electrical components and
switches.
(Note: Motors and switches are not waterproof)
- All components should be checked daily for tightness
BLADE CHANGE
1) Isolate from the power supply
2) Loosen the blade clamp bolts and slide out the blade. Insert the new blade and tighten the
clamp bolts
Note: The operator should be aware that the blades are sharp and use suitable
protection when handling them.
BLADE ANGLE
The angle of the blade can be altered to suit different applications
1) Loosen the thumb screws on either side of the chassis
2) Adjust the angle to a suitable setting
3) Tighten the thumb screws.
BASIC MAINTENANCE/CHECKLIST:
This checklist should be undertaken every8hrs to 10hrs - taking into accountthevibrating
action of machine
- DISCONNECT FROM THE POWER SUPPLY
- Check the condition of the blade
- Check all bolts and nuts for tightness
- Grease all moving parts on the sliding blade mechanism
- Check all the electric cables and plugs
2
MS230-2
MULTISTRIPPER
Operating Manual
SAFETY
1) Only trained operatives should be allowed to work the MS230
2) Appropriate PPE must be worn.
3) Keep hands and feet away from the moving blade at all times
4) Keep the electric lead away from the moving blade
5) Never leave the MS230 unattended whilst in use. Always stop the motor before
leaving the machine.
6) Always ensure that all power leads are disconnected before attempting to
service the machine. Never tip the machine backwards until the blade has stopped moving.
7) Do not use in wet conditions
8) Always use the correct voltage for the machine and RCD protection
9) Be careful when working around pipes or ducts protruding from the floor as the moving
blade may cause damage to them
10) Extreme care should be taken when changing the blades. The blades are sharp and
suitable protection should be used when handling them.
11) Equipment must be used in line with guidelines laid down by the Health & Safety
Executive.
Noise and vibration will occur at various levels dependent on the attachments and work being
completed. SPE have assessments conducted under test conditions detailed in the operating
manual, see page 10. However, it is recommended that additional tests are taken on site to
provide the operator with accurate information on using the equipment within the guidelines
laid down by the Health and Safety Executive.
3
23
22
11
12
10
15
21
14
3
26
24
7
16
18
20
8
2
17
27
13
19
14
5
6
1
9
25
NOT TO SCALE
SCALE
SHEET
3 of 3
DWG No.
MS230
ISSUE
REV
MS230-1
MULTISRIPPER
Operating Manual
MS230-2
MULTISTRIPPER
Operating Manual
Part no
Description
Qty
25MF@400V
Run Capacitor 230v
1
125MF@240V
Start Capacitor 230v
1
SP210-306
230v 16A 3 pin Trailing Plug
1
7536
1.5mm Cable - Black
5 mtrs
7
Ce manuel convient aux modèles suivants
1
Table des matières
