SpaceraiL 5.1 Manuel utilisateur

Instruction Manual Level 5.1

Elevator (enlargedview)

fg. 1

Quadloop(enlargedview)

SpaceRail Level 5.1

Table of Contents

Pendulum(enlargedview)

Seesaw(enlargedview)

Figure1..................................................... P. 2-3

Figure2-6..................................................... P. 4

PartsList...................................................... P. 5

Assemblyofthebaseplate.............................P. 6

Assemblyofthearms.................................... P. 6

Assemblyoftheseesaw..............................P. 6-7

Assemblyoftheelevator................................P. 7

Assemblyofthependulumandstarterkit.....P. 8-9

Assemblyofthebaseplate, gearbox,

pendulumandstarterkit.............................P. 8-9

Locationsof theelevatorrings.....................P. 8-9

Positionsofarms........................................P. 8-9

Rail assemblysteps.................................P. 10-11

Rail mounting.............................................. P. 12

Loopmounting............................................ P. 12

Elevatormounting(entryandexit).................P. 13

ConstructyourownStarCoasterdesigns........P. 14

Assembledproduct.......................................P. 15

Warnings.....................................................P. 16

Junction(enlargedview)

SpaceRail is a spectacular marble-run coaster that guarantees high-speed action rides cosisting of wild rotations, daring loop-

the-loops and spectacular swivel motions.These ball roller coasters are an ultimate challenge for teenagers and adult

enthusiasts alike. SpaceRails are available in diﬀerent sizes and diﬀerent levels of diﬃculty.

fg. 2 (front)

fg. 3 (left) fg. 4 (top)

fg. 6 (back)

fg. 5 (right)

These pictures show

the SpaceRail Level

5.1 from several

diﬀerent viewpoints.

This is very helpful to

reference during

assembly.

[B2] Baseholder (big) [B3] Baseholder (small) [G2] Gearboxsocket

[S6] ConnectingpieceA(176mm)

[S7] ConnectingpieceB(154mm)

[S8] ConnectingpieceC(90mm)

Steel balls

[R2] Rail joining [Ex2] Pendulum [Ex3] Starter Kit [Ex4] Breakcover for starterkit [Ex5] Ball catcher [Ex6] Counterweight [Ex7] Pendulumtrayfor steel balls

Parts List

Pliers

Use1 xC/ LR14 battery(not included).

Handlethecomponents withcareto prevent themfromgettinglost.

Tapemeasureorfoldingruler

Toolsforinstallation:

Partslist

[B1]

[A1]

[G1]

[B2] [B3] [S6] 176mm [S7] 154mm [S8] 90mm [G2]

[R2] [Ex2] [Ex3] [Ex4] [Ex5] [Ex6] [Ex7]

[E1] [E2] [E3] [Ex1] [P1]

[A2] [A3] [A4] [A5] [A6]

[S2] 300mm [S3] 200mm [S4] 159mm [S5] 65mm [R1] 32.000mm[S1] 391mm

[B1] Baseplate

[A1] Arm

[G1] Gear Box [E1] Elevator helix [E2] Elevator ring

[A2] ArmholderA [A3] Armtube [A4] ArmholderB [A5] Armwrench [A6] Rail stand

[S1] Shaft 391mm [S2] Shaft 300mm [S3] Shaft 200mm [S4] Shaft 159mm [S5] Shaft65mm [R1] Rail (32,000mm)

12x

80x

10x

80x

16x

80x

85x

165x

90x

11x 10x 2x 1x 1x 2x

[E3] Elevatorcover [P1] Junction[Ex1] Seesaw

Assemblyofbaseplate

1. Assemblethebaseplate

(12 pieces). Payattentionto

aproperseatingof theclips

and slots (fg. 01)

2. Fastenthebaseholders

(B2 +B3) inthecorrect

positions (fg. 01-2)

Assemblyofarms

1. Assemblethearms

accordingtofg. 02. Caution:

ArmholderA(A2) +arm

holderB(A4) aredifferent.

73arms areneededforthe

completeset-upof„Star

CoasterLevel 5“

2. Insert thearmwrenchinto

thearmholderAandturnit

by90 degrees tof xthearm

(fg. 03). Note:Tomodifythe

angleofthearm, releasethe

fxationfrst

3. Attachthearmtotheshaft

(fg. 04): Insert shaft intothe

armholderBandturnthe

armwrenchby90 degrees

tof xthearm(fg. 04). Note:

To modifythe angleof the

arm, releasethefxationfrst

Assemblyofseesaw

Insert 4x55mmrail intothe

holes of theseesaw. Then

attachtherail standtothe

seesaw(fg. 05)

Assembly of base plate, arms & seesaw

[B2] Baseholder(big)

[B3] Baseholder(small)

[B1] Baseplate

2[A3] Armtube

[A4] ArmholderB

Top-downview

[A2] Armholder A

[A5] Armwrench

Insertshaft intothearmholder B. Donot

applyforceinordertoavoiddamages

[A1] Arm

Note: When turningthearmwrench, makesurenot

to change the right positionof thearm

Note: When turningthearmwrench, makesurenot

to change the right positionof thearm. Refer to the

assemblyof arms (page E1-E4)

01-2

[A6] Rail stand

[Ex1]Seesaw

Approx. 55mm

[A6] Rail stand

[E2] Elevator ring

[E3] Elevator cover

[G1] Antrieb

[G1] Gearbox

Assemblyoftheelevator

1. Insertthe391mmshaft into

thegearbox(fg. 08-1)

2. Slidetheelevator(16pcs)

ontotheshaft (fg. 08-2).

Insert shaft intobase(fg.

08-1). Pleasenotethecorrect

directionof rotation

3. Insert 3further391mmshafts

intotheexact pre-defned

positions onthegearbox(fg.

08-3)

4. Allowthe3 shafts to snapinto

place(pic. 08-4). Takecare

that theelevator rings are

properlylocated. Seepage8

+9 for theproper locations of

theelevatorrings

5. Insert the4 shafts intothe

elevatorcover(fg. 08-5).

Takecarethat theshafts are

properlylocated

6. Nowattach3 rail stands [A6]

totheelevatorring(fg. 08-6)

Assemblyofseesaw

Attachseesawtotheshaft

(fg.06+07)

1. Connect seesawwitharm

holderB(fg. 06)

2. Attacharmholder Btothe

shaft (fg.07). Refer tothe

assemblyof arms (page10

andfollowing). Insertarm

wrenchintoarmholderBand

turnit by90 degrees (fg. 03).

Note: To modifytheangle of the

arm, releasethefxationfrst

Assembly of base plate, arms & seesaw

06 07

08-1

08-4

08-5 08-6

08-2 08-3

[A3] Armtube

[A4] ArmholderB

mountrighthandside

mountlefthandside

Install 1pcs

Holeprofle

Lochprofl

Holeprofle

Holeprofle Adjust seesawafter assemby

Note: Whenturningthearmwrench, makesurenot tochange

theright positionof thearm

[S1] Shaft 391mm

[E1] Elevatorhelix

Avoidthat thereis a gap between

gearboxandelevatorhelix.

Otherwisetheelevatorwill not

operateproperly. Pleasenotethe

correct directionof rotation

Makesureconvexred parts point

up andeverythingis correctly

seated.

Assembly of gear box and base plate

[G1] Gearbox

[S6- S8] Connectingpiece

Connect withholes onbaseplate

Seesaw(turnright)

Installationofthependulum

andstarterkit

1. Connect attachment parts with

pendulum(f g. 09). Note: To modify

thepositionof armholder B, release

thefxationfrst

2. Connect attachment parts with

starter kit (fg. 10). Note: To modify

thepositionof armholder B, release

thefxationfrst

Locationsof theelevatorrings

Elevator(fg.11): Elevatorisshowninascale

of1:1.Attachtheelevatorringstotheexact

pre-defnedredpositions (T-1,T-2,T-3)

Attachthe5clipsat thebottomofthe

gearbox(seeredmarkings infg.12) to

theexactpre-defnedpositionsof thebase

plate(fg.13)

Installationofgearbox,

pendulumandstarterkit

Locationof pendulumand starter kit on

base(fg.13)

Attachpendulum(fg. 09) andstarterkit

(fg.10) tothebaseplate(fg. 13)

Gearboxlocationonbaseplate(fg. 13)

Attachthe5 clips at thebottomof the

gearbox(see redmarkings inf g. 12) to

the exact pre-def nedpositions of the

baseplate(fg.13)

Positionsofarms

Attachthearms totheshafts (fg.14).Picture

showsascaleof1:1

Attachthearms totheshafts (seeillustration

forarminstallationonpageE1-E4)

Attachconnectingpiecestoshafts(fg.15+13)

Inserttheshaftsintothebaseplate(fg.13)

[S2] Shaft 300mm

[S5] Shaft 65mm

[S4] Shaft 159mm

[A4] Armholder B

[A5] Armwrench

[Ex5] Ball catcher

[Ex6] Counterweight

[Ex2] Pendulum

[A5] Armwrench

Referto theassemblyof arms (fg. 04)

Thecounterweight positionis adjustable

on theshaft if the pendulumdoes

not workproperly.Note: Tomodifythe

positionof counterweight, releasethe

fxationfrst

Referto theassemblyof arms (fg. 04)

Attachstarterkit (armholder B) totheshaft andcreateaslope, sothat

thesteel balls canrun smoothly

[S1] Shaft 391mm

[S2] Shaft 300mm

[A4] Armholder B

[A6] Rail stand

[Ex3] StarterKit

[A5] Armwrench

Pendulum

[Ex4] Brakecoverforstarter kit

Connect rails withtheentryof thestarter kit

and makef neadjustments to slowdownthe

speedof thesteel balls (balls will rebound if

toofast). Attachthebeakcovertothestarter

kit as shownin theillustration

Positionfor connectingpieceB

(154mm) [S7] Positionfor connectingpieceC

(90mm) [S8] Positionfor connectingpieceA

(176mm) [S6]

StarterKit Elevator

Vorderseite

Front

Back

Assembly of rails

JunctionA

[Ex7] Pendulumtrayforsteel balls

JunctionA

Rail assemblysteps

This ball roller coasterprovides 3

exits (start) and5 entries (end).

Pleasenotefg. 16-22andthe

illustrations onpage2-4 during

assembly

Install rail standstogetherwith

therails (fg. 26)

1. Fromelevatorexit (start) tothe

junctionAentry(end): Install 2

x61cmrails (fg. 16-1)

2. FromthejunctionAexit(start) to

thestarterkitentry(end):Install

2x117cmrails(fg.16-2)

Connect rails withtheentryof

thestarter kit andmakefne

adjustments to slowdownthe

speedof thesteel balls (balls will

rebound if toofast)

3. Fromstarterkit exit(start) to

theball catcher(end): Install 2

x58cmrails (fg. 16-3)

4. Frompendulumtrayforsteel

balls (start) toelevator entry

(end): Install 2 x40cmrails

(fg. 16-4)

5. FromthejunctionAexit (start)

tothelowerelevatorentry

(end): Install 2 x270cmrails

(fg. 17)

6a.Fromtheupperelevatorexit

(start) tobehindthetraverse

loops: Install 2 x507cmrails

(fg. 18). Caution: DoNOTcut

therails here(sectionwill be

continued as showninfg. 19)

Install 2x61cmrails Install 2x117cmrails Install 2x58cmrails Install 2x40cmrails

Do NOTcut therails here(section will be continued as shown in fg. 19)

16-1 16-2 16-3 16-4

Fromelevator exit (start) tothejunctionAentry(end) FromthejunctionAexit (start) tothestarter kit entry(end) Fromstarter kit exit (start) totheball catcher (end) Frompendulumtrayfor steel balls (start) to elevator entry (end)