Spaceman 6455-C Manuel utilisateur
Counter or Floor Standing
........................................................................................................................
.................................................................................................................
.....................................................................................................
.............................................................................................................
...................................................................................................................
..........................................................................................
Disassemble Parts ..........................................................................................................................6
Wash Parts .....................................................................................................................................7
Assemble Parts............................................................................................................................... 8
Sanize .........................................................................................................................................10
.......................................................................................................................
Introducon .................................................................................................................................11
Add Product to Machine ..............................................................................................................11
Freeze Product ............................................................................................................................11
Dispense Product ........................................................................................................................12
Wash ............................................................................................................................................12
Standby ........................................................................................................................................12
Low Mix Alarm .............................................................................................................................12
Light Box.......................................................................................................................................12
Spinner .........................................................................................................................................13
Adjust Product Consistency .........................................................................................................13
Machine Power Reset ..................................................................................................................13
........................................................................................................................
This machine has many built-in safety features to protect the operator while the machine is
running.
All personnel operang this machine read and understand this manual in its enrety. Failure to
comply with this manual may damage the machine and cause severe injury to the operator.
Denotes an acon that WILL cause
harm to the operator or machine if performed
incorrectly.
Informs the operator of a task that
may lead to harm if protocol is not properly
performed.
Represents a vital mechanical step
or note that the user must be aware of.
Non-hazard, but pay extra aenon.
Welcome to your Spaceman frozen beverage machine, engineered and designed to provide dependable
operaon and a consistent quality product. Your machine is approved for dairy and nondairy products, with
hopper refrigeraon funcon to maintain product temperature below 4oC (40oF), and with more automated
analog control system for operaonal ease and eciency . All models, countertop or oor, single or two avor,
operate in the same fashion.
This manual is a universal version that provides instrucons on installaon, operaon, cleaning and roune
maintenance. Informaon contained in this manual may be subject to change. Please check online or contact
your local Spaceman distributor for connued updates and detailed informaon about your Spaceman machine.
Unpack and inspect machine,
parts, and accessories.
Place machine in appropriate
food preparaon area. Comply
with all installaon requirements.
Read and understand
ALL safety and standard
operang procedures.
Fully disassemble machine,
and prepare parts for
cleaning.
Thoroughly clean and scrub
machine hoppers, cylinders,
and all parts.
Lubricate and re-assemble
all machine parts.
Prepare product in a separate
container, and ensure product
is thoroughly mixed.
Add product to hoppers
and prime the cylinder
using the prime plug.
Turn machine to FREEZE
mode, and wait for product
to reach frozen consistency.
Slightly adjust viscosity
seng as necessary to
adjust product rmness.
Inspect the machine for any shipping damage. If you nd any, contact Spaceman Technical Service immediately
aer unpallezing. Our technicians will help you assess the damage and determine the appropriate acon prior
to accepng the delivery.
1. Cut packing straps, and remove cardboard lid and outer sides from the pallet. DO NOT cut cardboard.
2. Remove plasc wrapping around machine.
3. Cut stabilizing straps, being careful not to scratch or dent the machine panels.
4. Prepare the area where the machine will be placed, remove packing cardboard from underneath machine,
and place ramp wedges near front casters.
5. Unlock front casters, and roll machine down the wedges o the pallet.
6. Place the machine in its nal locaon according to the Installaon Requirements.
: Unpallezing requires liing.
Failure to do so may result in severe injury or damage.
Inspect equipment for hidden damage before signing for delivery.
Refer to the detailed parts diagrams on the back pages if necessary.
1. Remove all packaged parts and accessories from your machine.
2. Organize items on a clean table or operang area using the checklist.
3. Inspect for damage immediately upon unpacking and call Spaceman
Technical Service if you discover any damaged or missing parts.
4. Clean and properly lubricate machine parts prior to machine operaon.
Included Parts:
• Hopper Cover (1 or 2)
• Front Drip Tray + Splash Shield
• Dispensing Handles
• Start-Up Kit
• Operator’s Manual
Fully sanize
machine.
Torque Arm
Dispensing Door with
Prime Plug, and Gasket
Draw Valve
with O-Rings
Ice Buster
Draw Valve Pin
Draw Handle Beater
Scraper Blade
Feed Tube
Beater Guide
Door Hand Screws
Torque Assembly
with O-Ring
Drive Sha Drive Sha Gasket
Brush Kit
(Oponal)
Internal Drip Tray O-Ring Removal Tool
Hopper Cover
Hopper Agitator
(if present)
Front Drip Tray
with Splash Shield
Torque Guide
The image displayed is for illustraon purpose only and may
dier from the actual product.
Spaceman requires that only the specied refrigerant be used
in your machine.
Alternave refrigerants may cause damage to the cooling
system and/or prevent the machine from operang at opmal
performance.
If you require an alternave refrigerant, please call Spaceman
Technical Support for a list of compable alternaves for your
compressor.
• Place on a at, level, and solid surface ed to
the machine dimensions
• Ensure a minimum 152mm (6'') clearance on
the exhaust side (Side or Back)
• Completely clear area of dust, grease, and
airborne parcles
• Place away from hot equipment such as stoves,
frying baskets, ovens, etc.
Failure to comply will damage the machine and refrigeraon components and will void all
warranes.
Operang in higher ambient temperatures will result in degraded performance.
1. Connect all wires to Circuit Breaker (including neutral & ground bus
terminals) or Local Plug according to supply voltage and wire codes on
machine power cable.
2. Verify Incoming Supply Cable is wired the same way on Circuit Breaker or
Wall Receptacle before switching on or plugging in the machine.
The image displayed is for illustraon purpose only and may
dier from the actual product.
• Daily
•: Every 1 to 3 months*
• Quarterly**
* Based on machine usage and cleaning intervals; a Tune-Up Kit is available with all
wearable parts (O-rings, gaskets, etc.) except scraper blades
** Based on cleanliness of locaon and proximity to powder-based machines.
Preventave maintenance includes cleaning condensers, checking belt tensions, and
cleaning the interior of the machine frame as required.
For opmal machine performance and many years of eciency and reliability
from your machine, Spaceman recommends cleaning and sanizing the
machine and its parts . The machine comes equipped with a brush kit
specically designed to eciently and properly clean the machine.
Cleaning and sanizing schedules are governed by state or local regulatory agencies
and MUST be followed accordingly. Roune maintenance MUST be performed a minimum of once
every 3 days.
• Do NOT run the machine without properly lubricang required parts
• Do NOT clean the machine with abrasive or toxic chemicals and cleaners. Doing so may cause
damage to the stainless steel material
• ONLY use Spaceman-included cleaning brushes and lubricaon
• NEVER use metal objects to clean or operate the machine
• ALWAYS replace wearable parts a minimum of every 3 months
• ALWAYS prime machine prior to operang
• ALWAYS inspect parts for excess wear and damage
Addional brushes, lubricaon, wearable parts, and tools can be purchased from Spaceman
to ensure proper maintenance. Extra wearable parts (except scraper blades) are found in the Start-
Up Kit.
If this is the rst me operang the machine, you MUST clean and sanize ALL parts
prior to running the machine.
The image displayed is for illustraon
purpose only and may dier from the
actual product.
-
1. Verify the power switch is turned to OFF.
2. Remove the torque arm, rst pulling up out of
the torque assembly and then down out of the
at sensor arm.
3. Remove dispensing door hand-screws (4).
4. Remove dispensing door assembly, torque
assembly, and beater assembly.
5. Remove torque assembly O-ring using O-ring
tool; remove torque guide.
6. Remove scraper blades from beater assembly
7. Remove dispensing door gasket using O-ring
tool.
8. Rotate draw valve unl the at part at the top is
perpendicular to the clear face of the dispensing
door (use towel if necessary).
9. Remove ice buster.
10. Remove draw valve, twisng it while removing.
11. Remove draw valve O-rings (2) using O-ring tool.
12. Unscrew and remove prime plug from
dispensing door.
13. Use a towel to remove drive sha at the back of
the cylinder.
14. Separate drive sha gasket from drive sha.
15. Remove front drip tray and internal drip tray.
Prepare dishwashing area prior to
disassembly, and use a bucket to temporarily store
removed parts.
Always separate O-rings and gaskets from
metal parts to prevent damage while washing.
1. Verify power switch is turned to OFF.
2. Use the large brush and cool water to thoroughly clean
inside the cylinder; be sure to scrub the back of the
cylinder and verify the cylinder is free of ALL product.
3. Thoroughly clean and dry the rear of the cylinder with
the supplied black brushes and a clean, dry towel.
4. Gently clean and wipe down the outside of the
machine.
5. Carefully and thoroughly wash all parts removed from
the machine using supplied brushes, sponges, and clean
towels; when cleaning the dispensing door, clean the
priming port with a small brush.
6. Carefully and thoroughly clean all gaskets and
O-rings removed from the machine; be sure to wipe
gaskets and O-rings to remove excess lubricant.
7. Verify all parts are clean and free of all food product
prior to re-assembling machine.
Never wash parts in a dishwasher. Always hand-wash components with nontoxic,
food-safe cleaners.
Never force the installaon of any parts. All parts t correctly without force. If parts
don’t seem to t, remove all parts and repeat assembly.
a. Place drive sha gasket on drive sha.
b. Seal gasket open space with Spaceman lubricant,
extending onto drive sha and avoiding the top square
part.
c. Insert drive sha into rear shell bearing at the back of
the cylinder, and turn it unl the key engages rmly into
the socket (when inserted correctly, the drive sha will
no longer turn 360°).
a. Place torque guide onto the end of the beater assembly; DO NOT lubricate this component.
b. Place O-ring on torque assembly, coang with Spaceman lubricant.
c. Insert torque assembly into torque guide at the end of beater assembly.
d. Fit scraper blades onto beater.
e. Insert the complete beater assembly into cylinder; turn assembly unl it engages the drive sha
key and no longer turns 360°.
a. Place O-rings (2) on draw valve, coang with Spaceman
lubricant.
b. Insert draw valve 7/8 way into the dispensing door from
the top, rotang as you install.
c. Turn draw valve so the at poron at the valve top is
perpendicular to the clear face of the dispensing door .
d. Insert ice buster through the dispensing spout at the
boom of the door and into the slot on the draw valve.
e. Rotate draw valve to lock ice buster in place; turn valve unl the hole for the draw handle is
accessible on front.
f. Insert draw handle; secure in place with valve pin.
g. Screw prime plug onto dispensing door.
h. Place dispensing door gasket on door, coang with Spaceman lubricant; Place beater guide onto
dispensing door, with ange ush with the back of the door.
i. Align door assembly with torque assembly and mounng bolts; install dispensing door unl ush
with machine; if needed, gently wiggle dispensing door to get the beater guide to line-up correctly
inside the beater; DO NOT force the dispensing door onto the machine.
j. Tighten dispensing door hand-screws (4) in a cross-paern.
k. With tapered end down, install torque arm up through the sensor pin hole under the overhead and
then down into the torque assembly; torque am should move freely back and forth.
a. If machine has hopper agitator,
lubricate inside it and install with arrow
poinng up.
b. Install hopper lid and drip trays (internal
and front).
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Spaceman Appareils de cuisine
