Souvia SMF700 Manuel utilisateur

Owner’s Manual

SMF MILK FROTHER

Smooth Stirring Head

(For Heating Milk)

Serrated Stirring Head

(For Frothing Milk)

Lid

SPECIFICATIONS

Model#: SMF700 Supply Voltage: 120V - 60Hz

Volume: 700 ml Power Consumption: 500W

Stainless Steel

Milk Container

Base

On/O Switch

Temperature

Control

Handle

FEATURES

pg 1

Main Indicator

Lamp

Power Cord

Storage

IMPORTANT SAFEGUARDS

This appliance is for HOUSEHOLD USE ONLY.

When using an electrical appliance, basic safety precautions should

always be taken, including the following:

1. READ ALL INSTRUCTIONS BEFORE USE.

2. Unplug from outlet when not in use and before cleaning. Allow unit to

cool before putting on or taking o parts, and before cleaning appliance.

3. The milk container heats up during operation. Do not touch hot

surfaces. Use handle.

4. To protect against re, electric shock and injury to persons, DO NOT

IMMERSE CORD, PLUG OR BASE UNIT in water or other liquids.

5. Close supervision is necessary when any appliance is used by or near

children.

6. Do not operate any appliance with a damaged cord or plug, or aer the

appliance has malfunctioned or has been damaged in any way. Return

appliance to the nearest authorized service facility for examination,

repair or adjustment.

7. The use of accessory attachments not recommended by Souvia may

result in re, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let power cord hang over edge of table or counter, or touch hot

surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated

oven.

11. Always put container on base, then plug cord into wall outlet. To

disconnect, press the ON/OFF button, then remove plug from wall

outlet.

12. This appliance is intended for heating up and frothing milk. Do not

put any other type of liquid or solid food in the container. Do not use

appliance for anything other than intended use.

13. Scalding may occur if the lid is opened during the heating cycle.

14. Do not use a cracked container or a container having a loose or

weakened handle.

SAVE THESE INSTRUCTIONS

pg 2

Short Cord Instructions

A short power supply cord is provided to reduce the hazards resulting

from entanglement or tripping over a longer cord. Longer detachable

power-supply cords or extension cords are available and may be used

if care is exercised in their use. If a longer detachable power-supply

extension cord is used:

1. The marked electrical rating of the cord set or extension cord should be

at least as great as the electrical rating of the appliance.

2. The cord should be arranged so that it will not drape over the counter

top or tabletop where it can be pulled on by children or tripped over

unintentionally.

3. If the appliance is of the grounded type, the extension cord should be

grounding type 3-wire cord.

Line Cord Safety Tips

1. Never pull or yank on cord or the appliance.

2. To insert plug, grasp it rmly and guide it into outlet.

3. To disconnect appliance, grasp plug and remove it from outlet.

4. Before each use, inspect the line cord for cuts and/or abrasion marks.

If any are found, this indicates that the appliance should be serviced

and the line cord replaced. Please return it to an authorized service

representative.

5. Never wrap the cord tightly around the appliance, as this could place

undue stress on the cord where it enters the appliance and cause it to

fray and break.

DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY

DAMAGE OR IF APPLIANCE WORKS INTERMITTENTLY OR STOPS

WORKING ENTIRELY.

This appliance must be grounded while in use. CAUTION: To ensure

continued protection against risk of electric shock, connect to properly

grounded outlets only.

IMPORTANT

During the rst few minutes of initial use, you may notice smoke and/or a

slight odor. This is normal and should quickly disappear. It will not recur

aer appliance has been used a few more times.

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

pg 3

OPERATING INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Before using for the rst time:

Prior to initial use, clean the unit by following the instructions in the

cleaning and care section of this manual.

We recommend the use of a long life milk (UHT) with a high protein

content. For best results, the milk should be taken from the refrigerator

immediately before frothing. Do not heat any liquid other than milk in

this appliance.

Choosing Stirring Head

To avoid uneven heating and burning of milk, Do not operate the milk

frother without a frothing disc inserted into the milk jug. Use only one

stirring head at a time.

 HEATING: use the smooth stirring head.

 FROTHING AND HEATING: To froth and heat milk at the same time;

use the serrated head.

 COLD-FROTHING: Use serrated head

Fill Amounts

 Always observe the minimum mark and ensure the container is lled

with at least 120 ml of milk.

 FROTHING: ll the container to a maximum of 350 ml (lower max

mark).

 HEATING: ll the container to a maximum of 700 ml (upper max mark).

Heating or Frothing Milk

1. Place the base on a rm, level surface.

2. Remove the lid from the milk container.

3. Place the appropriate head onto the mounting protrusion inside the

bottom of the container. NOTE: Do not operate the milk frother without

a frothing disc inserted into the milk jug - this can cause uneven heating

and burning of the milk.

pg 4

4. Put the required amount of milk into the container. Always use cold

milk and ll the milk jug between the MIN and MAX level markings.

Overlling the jug may cause spillage. Under lling the jug prevents the

frothing disc from working properly.

5. Place the lid on the container

6. Use the temperature control to set the desired temperature or to select

the cold-frothing function (COLD). The “COLD” setting will operate for

60 seconds before automatically stopping. If desired, you can re-select

the “COLD” setting. NOTE: If the temperature setting is changed during

operation, the milk frother will stop at the new temperature selection. If a

lower temperature is selected mid-cycle and the milk has already exceeded

the lower temperature selected, the milk frother will immediately stop.

7. Insert the plug into a proper outlet. a beep will sound and the main

indicator lamp will start to ash.

8. Press the ON/OFF button.

9. A double beep will sound, the indicator lamp remains on and the motor

cooling system starts up.

10. The stirring process begins. When the milk has reached the selected

temperature, the milk frother will automatically stop and beep twice.

Frothing functions take between 2 -7 minutes depending on the

amount of milk used. NOTE: Do not remove the milk jug from the power

base during operation. Doing so may disrupt the frothing disc and cause

grinding. Before removing the jug always stop operation of the unit by

pressing the START /STOP push-dial. Operation of the unit has stopped

once the button surround has stopped ashing.

11. The main indicator lamp ashes, and a number of beep signals will

sound.

12. You can now remove the milk container from the base. Use a suitable

spoon to take o the milk froth. NOTE: Aer 30 seconds of non-use, the

milk frother will enter standby mode. The button surround will cease to

illuminate. To reactivate the unit, turn or press the START/STOP push-dial.

13. The cooling system continues to run for a brief period. The main

indicator lamp stops ashing aer about three minutes.

14. The power cord can now be unplugged from the wall.

NOTE: if the appliance has not been disconnected from the outlet the ON/

OFF switch must be pressed twice to start a new operating cycle.

Aer a heating cycle, the appliance cannot start a new stirring and

heating cycle immediately. The unit must be allowed to cool down rst.

pg 5

pg 6

FUNCTION MILK AMOUNT

Cappuccino 350 ml

Latte 700 ml

Aer a cold-frothing cycle, a new stirring and heating cycle may be started

immediately.

Boil Dry, Overheating Protection - This unit is equipped with overheat-

ing protection. The unit will automatically shut o if the milk jug over-

heats. This is caused by insucient amount of milk in the milk jug or aer

too many consecutive uses. If this occurs, 3 alerts will sound. Unplug the

unit from the power outlet, wait approximately 5 minutes for the milk

frother to cool down. To speed up the cooling process, ll the milk jug

with cool water. Once adequately cooled, you will be able to reactive the

milk frother and recommence frothing

Tips

 To achieve a thicker froth, go through a cold-frothing cycle rst,

followed by a hot-frothing cycle.

 Making Hot Chocolate: The appliance is also suitable for preparing

hot chocolate. Proceed as described in the Heating or frothing section

of this manual. Fit the smooth stirring head into place and set the

temperature selector to 113˚F. As soon as the milk has been heated to

113˚F (as indicated by the corresponding beep signals), take off the lid

and add the required amount of cocoa powder. Set the temperature

selector to 149˚F and press the ON/OFF switch again. To prevent any

blockage or congestion, do not use grated chocolate or chocolate flakes

when making cocoa.

 Making Coee: refer to the table below for milk amounts when

preparing milk for coee.

pg 7

CLEANING & MAINTENANCE

DO NOT IMMERSE UNIT IN WATER

Do not clean container with cleansers, steel wool pads,

or other abrasive material.

1. Unplug your unit and allow it to cool before cleaning.

2. To avoid the risk of electric shock, do not clean the base or the power

cord with water and do not immerse them.

3. The milk container, stirring heads and lid should be cleaned aer each

cycle of use with hot water and a little detergent, or in a dishwasher.

If necessary, the serrated stirring head may be cleaned with a suitable

brush.

4. Wipe the outside of the base with a so, damp cloth.

Never immerse base in water. Servicing should be

performed by an authorized service representative.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Milk is not foaming Milk is warm or too

hot to foam.

• Use cold, fresh (or freshly

opened) milk.

• Do not re-foam already heated

milk.

• Try reducing the quantity of

milk in the milk jug.

• Try a dierent milk. Some milks

and milk brands produce more

froth than others. For example,

we have found that some soy

milks produce froth while others

do not. Experiment with dierent

milk options and frothing discs to

achieve the desired result.

• Adding dense ingredients like

thick syrups, heavy powders

and large akes can signicantly

reduce the amount of foam. This

is normal.

pg 8

PROBLEM POSSIBLE CAUSE SOLUTION

Milk is not heating • Ensure the milk jug is correctly

positioned onto the power base.

• Ensure that the milk frother

has been properly activated.

Frothing has started once the

milk frother beeps once and the

button surround slowly ashes. If

the milk frother does not do this,

re-push the START | STOP push-

dial once, rmly.

• Increase the temperature by

turning the START /STOP push-

dial to the right.

Frothing disc is not

moving or is dislodged

• Frothing disc is not

inserted correctly.

• Frothing disc

has dislodged during

operation.

• Ingredients have

been added too

quickly.

1. Stop operation.

2. Remove liquid from milk jug.

3. Ensure the frothing disc is

securely and correctly attached.

Once attached, turn the frothing

disc with your ngers, it should

turn freely. If it doesn’t, contact

Souvia Customer Service.

4. Rell milk jug with liquid.

5. Start frothing. Add ingredients

(if desired) slowly and in small

quantities aer the milk has

already started swirling.

3 Beeps sounding The milk frother may

be overheated.

1. Unplug the cord from the

power outlet.

2. Remove liquid from milk jug.

Rinse the milk jug and frothing

disc with cold water then dry

thoroughly.

3. Ensure the milk frother has not

been operated for 5 minutes. This

allows the internal components

to cool.

4. Ensure the frothing disc is

securely and correctly attached.

Once attached, turn the frothing

disc with your ngers, it should

turn freely. If it doesn’t, contact

Souvia Customer Service

5. Recommence frothing.

Humming noise This is normal. It is the

cooling fan preventing

the milk frother from

overheating.

During this time, you may still use

the milk frother unless the Boil

Dry Overheat Protection as been

activated (3 beeps will be heard).

Follow the instructions above.

PROBLEM POSSIBLE CAUSE SOLUTION

Burnt milk • Milk is not swirling

correctly.

• Milk jug has not been

cleaned properly and

milk residue from pre-

vious use is burning.

• Ensure the frothing disc is

securely and correctly attached.

Once attached, turn the frothing

disc with your ngers, it should

turn freely. If it doesn’t, contact

Souvia Customer Service.

• Ensure the milk jug is

thoroughly cleaned aer each

use and between consecutive

uses.

Ingredients are not

melting

• Ingredients have

been added before

milk has warmed up.

• Ingredients are too

large.

• Always allow the milk frother

to start for a few seconds before

using the measuring cap to grad-

ually add ingredients.

• Ensure ingredients are in small

pieces.

Milk is too cold or hot • Adjust the temperature to suit

your personal preference.

• Always ll the milk jug between

the MIN and MAX level markings.

Grinding noise • Frothing disc is not

inserted correctly.

• Frothing disc has

dislodged during operation.

• The milk jug has been

removed from the power

base during operation.

• Ensure the frothing disc is

securely and correctly attached.

Once attached, turn the frothing

disc with your ngers, it should

turn freely. If it doesn’t, contact

Souvia Customer Service.

• Removing the milk jug during

operation can dislodge the

frothing disc. Stop operation.

Reinsert the frothing disc

correctly before recommencing.

Emergency stop To stop operation at any time,

press the center of the START

/STOP push-dial. Operation

has stopped once the button

surround has stopped ashing.

pg 9

Table des matières

Autres manuels Souvia Appareils de cuisine

Souvia

Souvia MSC9555 Manuel utilisateur

Souvia

Souvia SV-120 Manuel utilisateur

Manuels Appareils de cuisine populaires d'autres marques

Tayama

Tayama TYG-35AF Manuel utilisateur

AEG

AEG 43172V-MN Manuel utilisateur

REBER

REBER Professional 40 Guide de l'utilisateur

North American

North American BB12482G / TR-F-04-B-NCT-1 Manuel utilisateur

Presto

Presto fountain popper Manuel utilisateur

Westmark

Westmark 1035 2260 Manuel utilisateur

Zanussi

Zanussi ZCG64396XA Manuel utilisateur

HOFFEN

HOFFEN SM-9302M Manuel utilisateur

Philips

Philips HD3133 Manuel utilisateur

Ronco

Ronco Beef Jerky Manuel utilisateur

Hendi

Hendi 470411 Manuel utilisateur

Livoo

Livoo MEN386 Manuel utilisateur

Vogue

Vogue D446 Manuel utilisateur

croydon

croydon WR-10313-700 Manuel utilisateur

ADE

ADE AUTOMATIC-L Manuel utilisateur

Chefman

Chefman RJ43-SQ Series Manuel utilisateur

Vacmaster

Vacmaster VP680 Manuel utilisateur

Jetmaster

Jetmaster 900HG Manuel utilisateur