Source SEM-CH-EXSIGN Manuel utilisateur

Installation &

Self Test Instructions

EMERGENCY HANGING BLADE

PRODUCT CODE: SEM-CH-EXSIGN

Quality

Assurance

years

Unit 7/8 Ashbourne Business Centre, Ballybin Road, Ashbourne, Co. Meath, Ireland, A84 YP58,

Phone: 00353 1 835 7447

Unit 32 Junction One Business Park, Valley Road, Birkenhead, Merseyside, UK, CH41 7ED,

UK Ph: 0330 551 7000

Website: www.sgd.ie

For more information contact:

Product end of life instruction.

This Lighting product is in the scope of EU 2019/2020 directive on Waste Electrical and Electronic Equipment

(WEEE). This product must be disposed of, according to the legislation. This document is intended for use by

end of life recyclers or treatment facilities. It provides the basic information to assure an appropriate end of life

treatment for the components and materials of the product.

Please follow pictured diagram on the back of this manual showing how to dismantle the product into different

components which should be disposed correctly. These components would consist of plastic, metal and

electronic materials.

It is the responsibility of the end user to dispose of this product correctly. www.weeeireland.ie or contact your

local council for further information.

DISASSEMBLY INSTRUCTIONS

IP20

COMPLIANT

1 21 3

Emergency Exit Sign surface suspended

AC 220-240V

x1 x1

45285

300

185

160

700

max. 45

1 2

Test

Please refer to this chart for more complete description / fault indication

Test Button Status

Green LED Constant Mains On / No Fault

Green LED Slow Flash Function for 2 minutes

Green LED Fast Flash 3 hour duration Test

Red LED 1 Flash Battery Fault

Red LED 2 Flash Lamp Fault

Red LED 3 Flash Duration Test Fault

Self-Test

Self-Test ttings perform a self-commissioning test at rst power on. After charging for 24 hours a full duration test (3 hours) is

performed. Initial function and duration tests are randomly generated.

They are then performed in accordance with standard requirements (every 30 days for function tests and every 52 weeks for

duration tests).

A single bi-colour indicator LED is tted in all Self-Test products. This LED is clearly visible for manual inspection. It indicates the

module status.

The LED shows permanent green or ashing green when conditions are normal and ashing red if a fault condition is present.

Function test

A function test is a 2 minutes test that simulates a mains failure and checks the operation of the emergency light source from the

battery supply.

The local indicator LED slow ashes green whilst the 2 minutes function test is in progress.

If there is a failure during a function test the local indicator LED changes to a ashing red.

Duration test

A duration test simulates a mains failure. It also checks the operation of the emergency light source from the battery supply for

the rated duration of the module.

The local indicator LED fast ashes green whilst the duration test is in progress.

If there is a failure during a duration test the local indicator LED either changes to ashing red.

The battery is required to be fully charged before a duration test can be started.

The test button of the unit has the following functions

Test Button Green LED Status

Press for about 1s Off Emergency mode for 1 second

Press for about 5s Slow ash Function for 30 seconds

Press for about 7s Fast ash 3 hour duration test

Press for about 10s End the duration test

Installation Instructions

• Provide power to the required point of installation, suitable IP rated junctions boxes should be used where required

• Mark the location of the xing holes and drill the holes ensuring not to infringe with any joists, gas or water pipes or electrical

cables

• Feed suspension cable through clamp

• Remove 2 screws on top of the tting (see g 1)

• This product can only be used in maintained operation (luminaire constantly on)

• Switch on the power supply and ensure the LED indicator is illuminated green. If it is not illuminated green, there may be a

battery fault

• The height of the sign can be adjusted via the compression clamp on the luminaire (see g 3)

Emergency Installation and Inspection

Serial/ Luminaire Number:

Installation / Test

Installed By: Date:

Record

Commissioned By: Date:

Year 1 Year 3*

*Recommended Battery Change LiFe P04

Year 4

Monthly test Signed Date Signed Date Signed Date Signed Date

Year 2*

*Recommended Battery Change NiCd

1 21 3

Emergency Exit Sign surface suspended

AC 220-240V

x1 x1

45285

300

185

160

700

max. 45

1 2

Test

EMERGENCY TESTING

Recommended routine test procedures are in line with BS 5266 & BS EN 50172 & I.S3217:2013-A1:2017.

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable

damage will occur if this instruction is not followed.

Daily check - check that status GREEN LED indicator is illuminated

Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch or switching off circuit

breaker. Ensure normal supply is restored after test and ensure indicator status LED is illuminated

Twice yearly conduct a one hour duration test - simulate a mains supply failure for 1 hour continnously by operation of key switch

or switching off a circuit breaker. Ensure normal supply is restored after test and the indicator status LED is illuminated

Annual full 3 hour duration test - conduct a 3 hour duration test - simulate a mains supply failure for 1 hour continnously by

operation of key switch or switching off a circuit breaker. Ensure normal supply is restored after test and the indicator status LED

is illuminated

If the luminaire fails any of the above tests - please contact a qualied electrician.

All Emergency lighting tests must be logged. The Emergency lighting logbook must be provided in order to be covered by any

warranties.

These instructions should be read carefully and retained after installation by the end user for future

reference and maintenance.

These instructions should be used to aid installation of the following product:

EMLSUS

GENERAL INSTRUCTIONS:

SAFETY:

INSTALLATION:

• Installation of this luminaire should only be carried out by a qualiﬁed electrician or competent

person to the current IEE Wiring Regulations (BS7671) & current Building Regulations

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit, including when this luminaire is ﬁtted, does not exceed the

rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for

installation

• This product is Class II double insulated

• This product is non-dimmable

• Provide power to the required point of installation, suitable IP rated junctions boxes should be used

where required

• Mark the location of the ﬁxing holes and drill the holes ensuring not to infringe with any joists, gas

or water pipes or electrical cables

• Feed suspension cable through clamp

• Remove 2 screws on top of the ﬁtting (see ﬁg 1)

Remove screws

LED indicator (green)Test button

• Connect the battery to the inverter via the plug and socket provided

• Connect the Live and Neutral to the push ﬁt terminals on the PCB of the inverter (Fig 2)

Fig1

Fig 2

Fig 3

• This product can only be used in maintained operation (luminaire constantly on)

• Switch on the power supply and ensure the LED indicator is illuminated green. If it is not

illuminated green, there may be a battery fault

• The height of the sign can be adjusted via the compression clamp on the luminaire (see ﬁg 3)

Press this part of the clamp

to adjust the length

Can be adjusted to a maximum

length of 800mm.

Live (brown)

Neutral (Blue)

These instructions should be read carefully and retained after installation by the end user for future

reference and maintenance.

These instructions should be used to aid installation of the following product:

EMLSUS

GENERAL INSTRUCTIONS:

SAFETY:

INSTALLATION:

• Installation of this luminaire should only be carried out by a qualiﬁed electrician or competent

person to the current IEE Wiring Regulations (BS7671) & current Building Regulations

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit, including when this luminaire is ﬁtted, does not exceed the

rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for

installation

• This product is Class II double insulated

• This product is non-dimmable

• Provide power to the required point of installation, suitable IP rated junctions boxes should be used

where required

• Mark the location of the ﬁxing holes and drill the holes ensuring not to infringe with any joists, gas

or water pipes or electrical cables

• Feed suspension cable through clamp

• Remove 2 screws on top of the ﬁtting (see ﬁg 1)

Remove screws

LED indicator (green)Test button

• Connect the battery to the inverter via the plug and socket provided

• Connect the Live and Neutral to the push ﬁt terminals on the PCB of the inverter (Fig 2)

Fig1

Fig 2

Fig 3

• This product can only be used in maintained operation (luminaire constantly on)

• Switch on the power supply and ensure the LED indicator is illuminated green. If it is not

illuminated green, there may be a battery fault

• The height of the sign can be adjusted via the compression clamp on the luminaire (see ﬁg 3)

Press this part of the clamp

to adjust the length

Can be adjusted to a maximum

length of 800mm.

Live (brown)

Neutral (Blue)

These instructions should be read carefully and retained after installation by the end user for future

reference and maintenance.

These instructions should be used to aid installation of the following product:

EMLSUS

GENERAL INSTRUCTIONS:

SAFETY:

INSTALLATION:

• Installation of this luminaire should only be carried out by a qualiﬁed electrician or competent

person to the current IEE Wiring Regulations (BS7671) & current Building Regulations

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit, including when this luminaire is ﬁtted, does not exceed the

rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for

installation

• This product is Class II double insulated

• This product is non-dimmable

• Provide power to the required point of installation, suitable IP rated junctions boxes should be used

where required

• Mark the location of the ﬁxing holes and drill the holes ensuring not to infringe with any joists, gas

or water pipes or electrical cables

• Feed suspension cable through clamp

• Remove 2 screws on top of the ﬁtting (see ﬁg 1)

Remove screws

LED indicator (green)Test button

• Connect the battery to the inverter via the plug and socket provided

• Connect the Live and Neutral to the push ﬁt terminals on the PCB of the inverter (Fig 2)

Fig1

Fig 2

Fig 3

• This product can only be used in maintained operation (luminaire constantly on)

• Switch on the power supply and ensure the LED indicator is illuminated green. If it is not

illuminated green, there may be a battery fault

• The height of the sign can be adjusted via the compression clamp on the luminaire (see ﬁg 3)

Press this part of the clamp

to adjust the length

Can be adjusted to a maximum

length of 800mm.

Live (brown)

Neutral (Blue)

Suspension Mounting Flush Ceiling Mounting

MOUNTING OPTIONS

Declaration Number:

100-SEM CH EXSIGN

This declaration of conformity is issued under the sole responsibility of the manufacturer.

Products:

Emergency led Exit Hanging Blade 3W, IP20 6500K Maintained & Non-Maintained

Model Number:

SEM CH EXSIGN

The product/model of the declaration described above is in conformity with the relevant

Community harmonisation legislation:

Low Voltage Directive (2014/35/EU)

EMC (2014/30/EU)

The product/model of the declaration described above is in conformity with the standards

and technical specifications listed below:

EN60598-2-22:2014+A1, EN60598-1:2015+A1, EN62471:2008, EN62493:2015,

EN55015:2013+A1, EN61547:2009, EN61000-3-2:2014, EN61000-3-3:2013, BS EN

62034:2012

Signed 07/12/2022

Autres manuels Source Équipement d'éclairage

Source

Source SFES10M Manuel utilisateur

Source

Source SEM-IP20 TW SP Manuel utilisateur

Source

Source SEM-REDL Manuel utilisateur

Source

Source SEM-EXB-P04 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur