Soredex Cranex D Manuel
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 1of 13
Cranex D Ceph beam alignment procedure (White Panel Unit Only)
This procedure is a quick guide that goes through the beam alignment
procedure. To make this easier, the tech should have the beam
alignment tool (Part # 203603) when performing the alignment.
Step#1: Be sure the main pan unit, ceph arm and head are level
before beginning.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 2of 13
Step #2: Get into service mode by doing the following:
Select Sr 11 EPS and press the E key and let
go (do not hold the button).
Press the left or right upper arch button to
select the different technique factors and
exposure time.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 3of 13
Press the return button Three times to ensure the pan head and
ceph head are aligned properly.
Step #3: Install the beam alignment tool on the Ceph sensor now.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 4of 13
Step #4: Remove the secondary collimator from the Ceph head by
removing the lock bolts and unplugging the ribbon cable.
Step #5: With the unit now in EPS mode and centered, make sure the
display reads 85 kV, 10 mA and 2.00 seconds. This gives you a
long enough exposure time to see the beam.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 5of 13
Step #6: Take an exposure, what’s needed is for the beam to
be within the Two outer vertical lines on the beam alignment
tool and also at the bottom line as shown below. Remember
the secondary collimator is off
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 6of 13
Step #7: If the beam is not within the lines horizontally, Loosen the
Four Torx screws that hold the Ceph head onto the arm. Slide the
head in or out until the beam is centered properly. Be sure to lock the
screws down once the beam is aligned.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 7of 13
Step #8: If the beam is not touching the bottom line in the tool, loosen
the Two bolts on the collimator that is in front of the
tubehead and then adjust both alignment screws. Be sure to
adjust these screws the same amount so the beam stays level.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 8of 13
Step #9: With the beam now centered, reattach the secondary
collimator and ribbon cable.
Step #10: With the unit still in EPS mode and the beam tool attached
to the ceph sensor, take another exposure. The beam needs to fall on
the entire Three inner vertical lines on the beam tool and also on the
bottom line. If the beam is way off, redo steps 7,8 and 9 again to
ensure the beam is correctly aligned
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 9of 13
Step #11: If the beam is out of alignment, then do the following:
Horizontal alignment:
A. Loosen the screw on the belt cog wheel
B. Insert a slotted screwdriver into the cog wheel end, while
holding the belt turn the screw in the desired direction to get the
secondary aligned properly.
Cranex® D Site Ceph Beam Alignment (White Panel Version)
Rev. 1 Cranex®D Ceph Beam Alignment (White Panel) Page 10 of 13
Vertical alignment:
C. If the beam is above or below the bottom horizontal line, loosen
the Two mounting screws and then adjust the top screw.
Tilt:
D. If the beam is going in a diagonal direction, adjust the side screw
to get the beam straight.
Autres manuels Soredex Équipement dentaire
Manuels Équipement dentaire populaires d'autres marques
Vatech
Vatech EzRay Air VEX-P300 Manuel utilisateur
KaVo
KaVo GENTLEpower LUX Contra-angle 25 LP Manuel utilisateur
DENTSPLY
DENTSPLY SmartLite Focus Manuel utilisateur
LM
LM ProPower CombiLED Manuel utilisateur
Owandy Radiology
Owandy Radiology RX-AC Manuel utilisateur
mectron
mectron Piezosurgery Manuel utilisateur
