Soredex made easy TWAIN 4.6 Manuel utilisateur
Digital imaging
made easy™
SOREDEX™ TWAIN 4.6
User manual
207892 rev. 6
ENGLISH
207892 iii
TWAIN 4.6
SOREDEX™TWAIN 4.6
User manual
Medical Device Directive
93/42/EEC
SOREDEX™ TWAIN 4.6
User manual
207892 rev. 6
Original approved English language version
Manufactured by Soredex, PaloDEx Group Oy
Nahkelantie 160
FI-04300 Tuusula,
FINLAND
Tel. +358 (0)10 270 2000
www.kavo.com
iv 207892
TWAIN 4.6
Documentation, trademark and the software are copyrighted with all rights re-
served. Under the copyright laws the documentation may not be copied, photo-
copied, reproduced, translated, or reduced to any electronic medium or machine
readable form in whole or part, without the prior written permission of SOREDEX.
SOREDEX, CRANEX, DIGORA, SCANORA and MULTICONNECT are either
registered trademarks or trademarks of Soredex in the United States and/or other
countries.
All other trademarks are property of their respective owners.
SOREDEX reserves the right to make changes in specication and features shown
herein, or discontinue the product described at any time without
notice or obligation. Contact your SOREDEX representative for the most current
information.
This software distributes and dynamically links to unmodied version of cross-plat-
form application and UI framework called Qt. The Qt UI framework is licensed
under GNU LGPL and the Qt source code is available from https://www.qt.io/.
Questions about the usage of components under GNU LGPL in this product can
207892 v
TWAIN 4.6
Contents
1. TWAIN................................................................................................................. 1
1.1 Introduction ................................................................................................... 1
1.2 About this manual.......................................................................................... 1
1.3 Software compatibility ................................................................................... 2
1.4 Symbols that may appear on the product ..................................................... 2
2. User’s Guide ...................................................................................................... 3
2.1 Opening TWAIN and acquiring images ......................................................... 3
2.2 Examining and adjusting images .................................................................. 6
Fullscreen shortcuts ................................................................................... 9
2.3 Saving (Returning) and deleting images ..................................................... 10
2.4 Retrieve last image ......................................................................................11
2.5 Retrieving images ....................................................................................... 12
2.6 Set as Auto-connect .................................................................................... 13
2.7 Device settings............................................................................................ 14
2.8 Closing TWAIN............................................................................................ 14
vi 207892
TWAIN 4.6
1. Introduction TWAIN 4.6
207892 1
1. TWAIN
1.1 Introduction
SOREDEX™TWAIN (hereafter called TWAIN)
is interface software for acquiring, viewing and
processing dental digital images via compatible
third-party dental imaging software.
Examples of this application include dental imaging
software from equipment manufactures, practice
management software and specialist imaging
software such as cephalometric tracing.
TWAIN allows digital dental images to be:
- Captured from SOREDEX, Instrumentarium
Dental, KaVo and Gendex digital imaging
device(s).
- Examined
- Adjusted to enhance their diagnostic value.
1.2 About this manual
This manual describes how to use TWAIN.
A separate installation manual is supplied that
describes how to install and congure TWAIN.
TWAIN must only be installed and setup by KaVo
trained and approved service personnel.
Before installing the software or using a digital
imaging device refer to the documentation supplied
with the device.
2 207892
TWAIN 4.6 1. Introduction
1.3 Software compatibility
TWAIN supports Windows 10, Windows 8.1
and Windows 7 operating systems. Refer to
the documentation supplied with Windows for
information about the Windows environment.
NOTICE:
If the SOREDEX, Instrumentarium Dental, KaVo or
Gendex imaging device(s) are used with a 3rd party
dental imaging software not produced or supported
by SOREDEX, the 3rd party dental imaging
software must comply with all applicable local laws
and regulations regarding dental imaging software.
This includes, for example, the Medical Device
Directive 93/42/EEC and/or FDA if applicable.
1.4 Symbols that may appear on the product
Name and address of the manufacturer
Catalogue number
Consult instructions of use
Electrical and electronic equipment waste,
dispose CD media and other parts according to
national laws and standards.
CE Mark
USA only: Caution: Federal law restricts this
device to sale by or on the order of a dentist.
Rx Only
207892 3
2. User’s guide TWAIN 4.6
2. User’s Guide
2.1 Opening TWAIN and acquiring images
1. Switch on the device(s) connected to the PC in
which TWAIN is installed
2. Open the dental imaging software you are using.
3. From the appropriate menu in the dental imag-
ing software select Acquire Image / Acquire.
4. The TWAIN window will open.
In the Select device eld, icons indicate what
devices have been congured to work with the
PC in which TWAIN is installed.
NOTICE:
If a congured device does not appear in the
Select device eld or if you want to add a new
device contact your service technician.
4 207892
TWAIN 4.6 2. User’s guide
5. From the Select device list click the device you
wish to use. If the device is ready to use the icon
will turn green and a check mark and the word
Ready will appear.
The device can now be used.
NOTICE:
If the device is Ready when TWAIN is opened, it
indicates that the auto-connect feature has been
activated. See 2.5 Set as Auto-connect.
If the device does not become ready after it has
been selected, dierent icon colors/symbols
indicate the status of the device.
The other device statuses are as follows:
Green, circle - Idle.
The device is ready but not reserved. Click the
icon to reserve it.
Yellow, dash - Busy.
The device is reserved by someone else or is
not ready for connection. Wait until the device is
released or ready.
Gray, disconnected line - Not connected.
The device cannot be found, or is switched o or
disconnected. Check that the device is on and
connected to the PC.
Gray, rotating circle - Waiting.
Connecting to a device.
Red, cross - Error.
Device error. Make sure that the device is on
and functioning correctly.
Table des matières
Autres manuels Soredex Imprimante tout-en-un
Manuels Imprimante tout-en-un populaires d'autres marques
Triumph Adler
Triumph Adler DC 2016 Manuel
Epson
Epson WorkForce WF-2510 Guide de l'utilisateur
Epson
Epson Stylus Scan 2000 Manuel d'installation et d'exploitation
Epson
Epson PictureMate Snap PM 240 Mode d’emploi
Konica Minolta
Konica Minolta bizhub C35 Manuel utilisateur
Brother
Brother MFC-J430w Manuel utilisateur
