Sony BKPF-105A Manuel utilisateur
A/V MULTIPLEXER BOARD
BKPF-105A/205/205R
INSTALLATION MANUAL
1st Edition
A/V DEMULTIPLEXER BOARD
BKPF-106A/206/206R
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
BKPF-105A (SY) Serial No.10001 and Higher
BKPF-106A (SY) Serial No.10001 and Higher
BKPF-205 (SY) Serial No.10001 and Higher
BKPF-205R (J) Serial No.20001 and Higher
BKPF-206 (SY) Serial No.10001 and Higher
BKPF-206R (J) Serial No.20001 and Higher
1(E)
BKPF-105A/205/205R
BKPF-106A/206/206R
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 2 (E)
Contents ............................................................................................................... 2 (E)
Related manual .................................................................................................... 2 (E)
1. Installation
1-1. Installation of Boards ............................................................................1-1 (E)
1-2. Information of BKPF-105A ..................................................................1-3 (E)
1-2-1. Contents................................................................................1-3 (E)
1-2-2. Location and Function of Connectors ..................................1-3 (E)
1-2-3. Connectors and Cables .........................................................1-3 (E)
1-2-4. Location and Function of Switches/LEDs ...........................1-4 (E)
1-2-5. ISR........................................................................................1-7 (E)
1-3. Information of BKPF-106A ..................................................................1-8 (E)
1-3-1. Contents................................................................................1-8 (E)
1-3-2. Location and Function of Connectors ..................................1-8 (E)
1-3-3. Connectors and Cables .........................................................1-8 (E)
1-3-4. Location and Function of Switches/LEDs ...........................1-9 (E)
1-3-5. ISR......................................................................................1-11 (E)
1-4. Information of BKPF-205 ...................................................................1-12 (E)
1-4-1. Contents..............................................................................1-12 (E)
1-4-2. Location and Function of Connectors ................................1-12 (E)
1-4-3. Connectors and Cables .......................................................1-12 (E)
1-4-4. Location and Function of Switches/LEDs .........................1-13 (E)
1-4-5. ISR......................................................................................1-16 (E)
1-5. Information of BKPF-206 ...................................................................1-17 (E)
1-5-1. Contents..............................................................................1-17 (E)
1-5-2. Location and Function of Connectors ................................1-17 (E)
1-5-3. Connectors and Cables .......................................................1-17 (E)
1-5-4. Location and Function of Switches/LEDs .........................1-18 (E)
1-5-5. ISR......................................................................................1-21 (E)
2(E) BKPF-105A/205/205R
BKPF-106A/206/206R
Manual Structure
Purpose of this manual This manual is the installation manual of the following boards. This manual is
intended for use by trained system and service engineers, and describes the
information for installation.
.A/V Multiplexer Board BKPF-105A
BKPF-205
.A/V Demultiplexer Board BKPF-106A
BKPF-206
Contents This manual is organized by following sections.
1-1. Installation of Boards
This section explains how to install the boards in digital video interface unit (PFV-
D20/D50/D100A/D200A/D300).
1-2. Information of BKPF-105A
1-3. Information of BKPF-106A
1-4. Information of BKPF-205
1-5. Information of BKPF-206
These sections explain the contents, the location and function of connectors, the
location and function of switches and LEDs, and the ISR (Interactive Status
Reporting), etc.
Related manual The following manual is prepared for BKPF-105A/106A/205/206.
..
..
.Operation Manual (Supplied with BKPF-105A/106A/205/206)
This manual describes the notes on operating, the locations and functions of parts,
and controls of each board.
..
..
.BKPF-105A Maintenance Manual (Optional manual)
..
..
.BKPF-106A Maintenance Manual (Optional manual)
..
..
.BKPF-205 Maintenance Manual (Optional manual)
..
..
.BKPF-206 Maintenance Manual (Optional manual)
These manuals describes the information for periodic maintenance and detailed
service. For obtaining the Maintenance Manual, please contact to your local
Sony’s sales/service office.
1-1(E)
BKPF-105A/205/205R
BKPF-106A/206/206R
Section 1
Installation
3. Insert the main board along the board guide rails.
PSW 3x6
PSW 3x6Board retainers
1-1. Installation of Boards
This section explains how to install the boards in PFV-
D300. When installing the boards in the models other than
PFV-D300, refer to the manuals supplied with the models.
The boards can be installed in any empty slot of PFV-
D300.
n
For your safety, turn off the power of PFV and unplug the
power plug from the outlet before installing or removing
the boards.
Installation of the main board
1. Loosen the four screws (with stoppers) and remove the
front panel.
2. Remove the six screws and remove the board retainers.
Board guide rail
Component side
Main board
1-2(E) BKPF-105A/205/205R
BKPF-106A/206/206R
4. Turn the board levers in the direction of the arrow 1
after inserting the main board to the end of the slot by
hand.
5. Stick the slot number label supplied with the board
onto the board lever.
6. Install the board retainers.
7. Install the front panel.
n
When removing the main board, turn the board levers in
the direction of the arrow 2, and pull out the board
toward you.
1Insert
2Remove
12
1
2
12
Board
lever
1
2
Board
lever
Installation of the connector panel
1. Remove the two screws and remove the blank panel
corresponding to the slot which the main board has
been installed.
n
Keep the blank panel which is removed.
2. Insert the connector panel.
3. Secure the connector panel with the two screws
securing the blank panel.
n
Do not open the slot for realizing an air-cooled effect of
PFV-D300. Install the blank panel to an empty slot.
B 3x6
Blank panel
B 3x6
Connector panel
1-1. Installation of Boards
1-3(E)
BKPF-105A/205/205R
BKPF-106A/206/206R
1-2. Information of BKPF-105A
1-2. Information of BKPF-105A
1-2-1. Contents
Contents of BKPF-105A are as follows.
.AVM-6 board (1)
.Connector panel (CN-1481 board) (1)
.Operation manual (1)
.Installation manual (1)
.Slot number label (1)
1-2-2. Location and Function of Connectors 11
11
1SDI IN connector (BNC type):
Accepts a 4:2:2 component or 4fsc NTSC composite
serial digital video signal.
22
22
2Active-through output connector (BNC type):
Outputs the signal supplied to the SDI IN connector
after its waveform has been shaped.
33
33
3AES/EBU IN connectors (BNC type):
Accepts an AES/EBU digital audio signals.
Connector 1 : 1/2 CH (or 5/6 CH in group 2)
Connector 2 : 3/4 CH (or 7/8 CH in group 2)
n
Be sure to supply digital audio signals being locked to
the digital video signal. Otherwise, noise may occur.
44
44
4WORD SYNC OUT connector (BNC type):
Outputs an audio word sync signal. This signal is
supplied only when a signal is supplied to the SDI IN
connector.
55
55
5SDI OUT connectors (BNC type):
Outputs a signal obtained by multiplexing the audio
signals supplied to the AES/EBU IN connectors with
the serial digital video signals supplied to the SDI IN
connector and adding an EDH process to the
multiplexed signal.
Connector 1 and 2 output the same signal.
1-2-3. Connectors and Cables
If any connector or cable is connected to the connectors on the connector panel
when installing or servicing, use the connectors or cables listed below or equivalent.
BKPF-105A Connector Matching Connector/Cable
Panel Indication Connector Connector Sony Part No.
SDI IN BNC (75 Z) BNC (75 Z) 1-560-069-11
AES/EBU IN BELDEN 8281 cable _
WORD SYNC OUT
SDI OUT
AVM
SDI IN
AES/EBU IN
WORD SYNC
OUT
SDI OUT
BKPF-105A
1
2
1
2
1
2
3
4
5
1-4(E) BKPF-105A/205/205R
BKPF-106A/206/206R
1-2. Information of BKPF-105A
1-2-4. Location and Function of Switches/
LEDs
AVM-6 board
Component side (A side)
11
11
1D511 and D512 : AUDIO EXIST indicators
These indicators indicate the existence of an AES/
EBU digital audio input signal. They light in green
when an input signal exists.
D511 D512
Group 1 1/2 CH 3/4 CH
Group 2 5/6 CH 7/8 CH
22
22
2D513 and D514 : AUDIO ERROR indicators
These indicators indicate the error of an AES/EBU
digital audio input signal. They light in red when an
input signal is not in synchronization with an audio
clock and an error occurs.
D513 D514
Group 1 1/2 CH 3/4 CH
Group 2 5/6 CH 7/8 CH
33
33
3S501 : Mode set switch (8-poles DIP switch)
Factory settings : All "OFF" side
S501-1 : D1/D2 system select switch
This switch selects the system of the video signal.
D1 : 4:2:2 component serial digital video signal
D2 : 4fsc composite serial digital video signal
S501-2 : Audio group select switch
This switch selects the group number of the audio data
to be multiplexed.
1
2
3
4
5
6
7
8
9
!/
In D1 mode
GP1 : Group 1
The DID in a signal is set to audio group 1.
The AES/EBU digital audio input signal is multiplexed
as 1 CH through 4 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal,
the input digital audio signal is multiplexed after all
audio data are erased.
GP2 : Group 2
The DID in a signal is set to audio group 2.
The AES/EBU digital audio input signal is multiplexed
as 5 CH through 8 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal
and the DID of audio data has been set to audio group 1,
the digital audio signal is multiplexed later than the
audio data. When the data of audio group 1 is not
detected, D705(MULTIPLEX ERROR indicator) lights
in red and the audio data is not multiplexed.
In D2 mode
GP1 : Group 1
The DID in a signal is set to audio group 1.
The AES/EBU digital audio input signal is multiplexed
as 1 CH through 4 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal,
the input digital audio signal is multiplexed after all
audio data are erased. In D2 mode, the DID is usually
set to audio group 1.
GP2 : Group 2
The DID in a signal is set to audio group 2.
The AES/EBU digital audio input signal is multiplexed
as 5 CH through 8 CH in an SDI signal. If audio data
has been already multiplexed into the input SDI signal,
the input digital audio signal is multiplexed after all
audio data are erased. In D2 mode, only one group can
be multiplexed at a time. The DID is not set to audio
group 2 usually.
S501-3 : Factory use only
Keep as the default setting.
1-5(E)
BKPF-105A/205/205R
BKPF-106A/206/206R
1-2. Information of BKPF-105A
S501-4 and S501-5 :
Inhibit switches of audio multiplexing
These switches are inhibit switches of audio multiplexing.
S501-4
OFF : Multiplexes 1/2 CH normally.
ON : Inhibits multiplexing 1/2 CH.
S501-5
OFF : Multiplexes 3/4 CH normally.
ON : Inhibits multiplexing 3/4 CH.
n
Audio multiplexing cannot be performed when no digital
audio signals are input to AES/EBU IN connectors 1 and
2.
S501-6 and S501-7 : Digital mute switches
These switches mute the audio data of an AES/EBU digital
audio input signal digitally (logically).
S501-6
OFF : Multiplexes the audio data of an AES/EBU
digital audio input signal into 1/2 CH.
ON : Multiplexes the digital muted audio data into
1/2 CH.
S501-7
OFF : Multiplexes the audio data of an AES/EBU digital
audio input signal into 3/4 CH.
ON : Multiplexes the digital muted audio data into
3/4 CH.
n
No audio data can be multiplexed when switches S501-4
and S501-5 are set to ON or when no digital audio signal
is input to AES/EBU IN connectors 1 and 2. Therefore,
the settings of S501-6 and S501-7 are disabled in this
case.
S501-8 : 3/4 OPE (3/4 CH operation) switch
The input signal to 1/2 CH can be multiplexed into 3/4 CH
if no digital audio signal is input to 3/4 CH.
OFF : Multiplexes the digital audio input signal to AES/
EBU IN connector 2 as 3/4 CH.
ON : Copies the digital audio input signal to AES/
EBU IN connector 1 and multiplexes it as 3/4 CH.
n
The setting of this switch is disabled when switch S501-
5 is set to ON (inhibits multiplexing 3/4 CH).
44
44
4D701 : SDI IN indicator
This indicator lights in green when a serial digital
video signal corresponding to the setting of S501-1
(D1/D2 system select switch) is input to the SDI IN
connector. It lights in red when no serial digital video
signal is input or when a signal not corresponding to
the system is input.
55
55
5D702 : EDH (Error Detection and Handling)
indicator
This indicator lights in green when the EDH data in
the serial digital video input signal to the SDI IN
connector is normal during detection. It lights in red
when an error is detected by the EDH data. It goes off
when a serial digital video signal containing no EDH
data is input.
66
66
6D703 : SDI OUT indicator
This indicator indicates the existence of the output
signal from the SDI OUT connector. This indicator
lights in green when an output signal exists. It lights
in red when no output signal exists.
77
77
7D705 : MULTIPLEX ERROR indicator
This indicator lights in red when switch S501-2 is set
to group 2 (GP2), but when the audio data of group 1
cannot be detected in an SDI signal. This indicator
goes off when it is in the normal state.
88
88
8S601 : Free-running adjustment switch of
serial decoder
This switch is used during free-running adjustment of
a serial decoder.
OFF : Set during normal operation.
ON : Set during free-running adjustment of a serial
decoder.
Factory setting : OFF
99
99
9S801 : Free-running adjustment switch of
serial encoder
This switch is used during free-running adjustment of
a serial encoder.
OFF : Set during normal operation.
ON : Set during free-running adjustment of a serial
encoder.
Factory setting : OFF
1-6(E) BKPF-105A/205/205R
BKPF-106A/206/206R
1-2. Information of BKPF-105A
!/!/
!/!/
!/ S802 : WORD SYNC SELECT switch
The BKPF-105A has a word sync output signal of 48
kHz so as to synchronize to other audio A/D converter
board (BKPF-201, BKPF-201R, etc.). This switch
selects the word sync output level.
NORMAL (1 V p-p) :
This level was newly determined as a signal format
that is used for synchronization of associated digital
audio equipments of BKPF series . This is a 48 kHz
square wave signal of 75 Zline 1 V p-p without DC
offset (DC level is 0 V). The signal can also be
distributed by using a normal video distributor.
HIGH (0 - 5 V) :
This signal conforms to the audio word sync signal
used in the conventional digital audio equipment. It is
a 48 kHz square wave signal of 75 Zterminated with
an amplitude of approximately _0.3 +2.6 V. The
signal cannot be distributed by using an external video
distributor.
Factory setting : NORMAL
Autres manuels pour BKPF-105A
1
Ce manuel convient aux modèles suivants
7
Table des matières
Autres manuels Sony Multiplexeur
Manuels Multiplexeur populaires d'autres marques
ADTRAN
ADTRAN Frameport 768 Manuel utilisateur
Elo TouchSystems
Elo TouchSystems E247 Manuel utilisateur
Paradyne
Paradyne Hotwire 8786 Manuel utilisateur
RFL Electronics
RFL Electronics 9508D UCC Manuel utilisateur
Miranda
Miranda AMX-101i Mode d’emploi
ShipModul
ShipModul MiniPlex-AIX NMEA-0183 Manuel utilisateur
