Sony NW-E103 - Network Walkman Manuel utilisateur

SERVICE MANUAL

Sony Corporation

Connect Company

Published by Sony Engineering Corporation

US Model

Canadian Model

AEP Model

NW-E103/E105/E107

E Model

NW-E103/E105

Australian Model

NW-E107

Tourist Model

NW-E103/E105/E107

PORTABLE IC AUDIO PLAYER

9-879-540-05

2005I16-1

Ver. 1.4 2005.09

SPECIFICATIONS

NW-E103/E105/E107

Frequency response

20 to 20,000 Hz (single signal measurement)

Interface

Headphone: Stereo mini

USB

Signal-to-noise ratio (S/N)

80 dB or more (excluding ATRAC3 66 kbps)

Dynamic range

85 dB or more (excluding ATRAC3 66 kbps)

Operating temperature

5˚C to 35˚C (67˚F to 95˚F)

Power source

Size AAA (LR03) alkaline battery

Battery life (continuous

playback)

ATRAC3 format: Approximately 70 hours

(Playback at 105 kbps)

ATRAC3plus format: Approximately 60 hours

(Playback at 48 kbps)

MP3 format: Approximately 50 hours

(Playback at 128 kbps)

Dimension

56.2 ×56.2 ×19.2 mm (2

⁄

×2

⁄

inches)

(w/h/d, projecting parts not included)

Mass

Approx. 26 g (1oz) (battery not included)

Supplied accessories

Headphones (1)

Dedicated USB cable (1)

CD-ROM for the SonicStage software, PDF file

Operating Instructions and PDF file SonicStage

Operating Instructions (1)

Quick Start Guide

Design and specifications are subject to

change without notice.

Sampling frequency

ATRAC3, ATRAC3plus: 44.1 kHz

Audio compression technology

Adaptive Transform Acoustic Coding3 (ATRAC3)

Adaptive Transform Acoustic Coding3plus

(ATRAC3plus)

MPEG1 Audio Layer-3 (MP3): 32 to 320 kbps,

variable bit rate-compliant

Maximum recording time (Approx.)

ATRAC3plus

2 hr. 10 min. (256 kbps)

8 hr. 40 min. (64 kbps)

11 hr. 40 min. (48 kbps)

ATRAC3

4 hr. 10 min. (132 kbps)

5 hr. 20 min. (105 kbps)

8 hr. 30 min. (66 kbps)

NW-E103

ATRAC3plus

4 hr. 20 min. (256 kbps)

17 hr. 30 min. (64 kbps)

23 hr. 30 min. (48 kbps)

ATRAC3

8 hr. 30 min. (132 kbps)

10 hr. 40 min. (105 kbps)

17 hr. 00 min. (66 kbps)

NW-E105

MP3

2 hr. 10 min. (256 kbps)

4 hr. 20 min. (128 kbps)

MP3

4 hr. 20 min. (256 kbps)

8 hr. 50 min. (128 kbps)

ATRAC3plus

8 hr. 50 min. (256 kbps)

35 hr. 00 min. (64 kbps)

47 hr. 00 min. (48 kbps)

ATRAC3

17 hr. 00 min. (132 kbps)

21 hr. 40 min. (105 kbps)

34 hr. 10 min. (66 kbps)

NW-E107

MP3

8 hr. 50 min. (256 kbps)

17 hr. 40 min. (128 kbps)

US and foreign patents licensed from

Dolby Laboratories.

NW-E103/E105/E107

TABLE OF CONTENTS

1. GENERAL ................................................................... 3

2. DISASSEMBLY ......................................................... 5

3. TEST MODE ............................................................... 6

4. DIAGRAMS

4-1. Block Diagram ................................................................ 9

4-2. Printed Wiring Board – MAIN Board (Side A) –........... 10

4-3. Printed Wiring Board – MAIN Board (Side B) –........... 11

4-4. Schematic Diagram – MAIN Board (1/3) – ................... 12

4-5. Schematic Diagram – MAIN Board (2/3) – ................... 13

4-6. Schematic Diagram – MAIN Board (3/3) – ................... 14

5. EXPLODEDVIEWS

5-1. Overall-1.......................................................................... 15

5-2. Overall-2.......................................................................... 16

5-3. Overall-3.......................................................................... 17

6. ELECTRICAL PARTS LIST .................................. 18

Microsoft, Windows and Windows Media are trademarks or

registered trademarks of Microsoft Corporation in the United States

and/or other countries.

US and foreign patents licensed from Dolby Laboratories.

All other trademarks and registered trademarks are trademarks or

registered trademarks of their respective holders.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270 °C

during repairing.

•Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering

or unsoldering.

Notes on chip component replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be

damaged by heat.

NW-E103/E105/E107

SECTION 1

GENERAL This section is extracted

from instruction manual.

Locating controls

For details about each part, refer to the pages in parentheses.

Rear sideFront side

1Nx button

(page 14, 16 to 17, 19 to 22, 24, 26 to

33)

2Display (page 11, 18, 43)

For details on the display and icons,

refer to page 11.

3.–/+>button

(page 16 to 17, 19 to 22, 24, 26 to 33)

4i(headphone) jack (page 14)

5VOLUME +/– button

(page 14, 28 to 29)

6Strap hole for attaching a strap

7MENU button (page 16 to 22, 24, 26 to

33)

You can switch to the Time display by

pressing and holding the MENU button.

8Battery compartment (page 9)

9REPEAT/SOUND button

(page 18 to 20, 23)

q; GROUP/HOLD switch

(page 15 to 16, 23, 25)

: Group mode. Play or search songs

by group (page 23).

: Normal mode. Play songs by track

name (page 16).

HOLD: Protect the Network Walkman

against accidental operation (page 25).

qa USB jack (page 12)

Text/graphic information display (page

17)

Displays track number, track name,

current date and time (page 22 to 23,

26), MESSAGE (page 13, 43) and menu.

Press the MENU button to switch the

display mode. For details, refer to

“Changing the display mode” on page

22.

2Repeat mode indication (page 18)

The current repeat mode is displayed.

3AVLS indication (page 27)

The indication appears while the AVLS

function is activated.

4Digital sound preset indication

(page 23 to 24)

The current sound setting is displayed.

5Remaining battery indication (page 9)

The remaining battery power is

displayed.

Display

NW-E103/E105/E107

3Press the .–/+>button to

adjust the “year” setting and

press the Nx button to confirm.

The “month” digit blinks.

2005y 1m 1d

4As you did in step 3, adjust the

settings for “month” and “date.”

After pressing the .–/+>button

to adjust the “date” setting and pressing

the Nx button to confirm, the display

switches to the time setting screen.

1:00

5Press the .–/+>button to

adjust the “hour” setting and

press the Nx button to confirm.

The “minute” digit blinks.

1:00

6As you did in step 5, adjust the

settings for “minute.”

After pressing the .–/+>button

to adjust the “minute” setting and

pressing the Nx button to confirm, the

display switches to the time setting

screen.

E-

IME

7Press the MENU button.

The display returns to the normal screen.

Adjusting the

current time

setting

(DATE-TIME)

You can set and display the current time.

1Press the MENU button.

The menu screen is displayed.

REPEATMODE

2Press the .–/+>button to

select “DATE-TIME” and press the

Nx button to confirm.

The “year” digit blinks.

2005y 1m 1d

Nx button

MENU button

.–/+>button

NW-E103/E105/E107

SECTION 2

DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

two claws

cosmetics plate

The

cosmetics plate

is removed in the direction of the arrow.

(Damage attention of four claws of

cosmetics plate)

two screws (1.4)

front cabinet

two adhesive sheets (plate, cosme)

two claws

cosmetics plate

two adhesive sheets (plate, cosme)

two claws

NW-E103/E105/E107 SECTION 3

TEST MODE

STANDING PROCEDURE

Procedure 1: In HOLD state, while pushing Nx button, set a

dry battery.

When the test mode is set, the LCD display appears

as shown below.

Procedure 2: After starting up test mode, the following contents

can be checked. (Before key input, select the

from HOLD state with S706.)

TEST MODE

• Nx button

The KEY test mode is activated. All key inputs are completed,

then Nx button is pressed, restart. (Be aware that the

initialization is included on all key input.)

• [MENU] button

EL0: ON/OFF EL back lights on/off.

• + > button

Ports: ON EL back lights on.

• . – button

Ports: OFF EL back lights off.

• + > button ( state with S706)

All LCD lights on.

• . – button ( state with S706)

All LCD lights off.

• [VOLUME +] button

BEEP turns on.

• [VOLUME --] button

BEEP turns off.

• [ REPEAT SOUND] button

Initialized. (Turns to the factory preset state, time, volume setting

and so on.)

The music data, files and so on in the memory are not changed.

•

512M 1.00.00 J11

NW-E103/E105/E107

SECTION 4

DIAGRAMS

Note on Schematic Diagram:

•All capacitors are in µF unless otherwise noted. (p: pF) 50 WV

or less are not indicated except for electrolytics and tantalums.

•All resistors are in Ωand 1/4W or less unless otherwise speci-

fied.

•%: indicates tolerance.

•C: panel designation.

•: B+ Line.

•Power voltage is dc 1.5V and fed with regulated dc power sup-

ply from battery terminal.

•Voltages and waveforms are dc with respect to ground under

no-signal (detuned) conditions.

no mark : PLAY

*: Impossible to measure

•Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations maybenotedduetonormalproductiontoler-

ances.

•Waveforms are taken with a oscilloscope.

Voltage variations maybenotedduetonormalproductiontoler-

ances.

•Circled numbers refer to waveforms.

•Signal path.

E: PLAY BACK

a: DIGITAL OUT

k: DIGITAL IN

Note on Printed Wiring Board

• X: parts extracted from the component side.

• Y: parts extracted from the conductor side.

• : Pattern from the side which enables seeing.

Caution:

Pattern face side: Parts on the pattern face side seen from

(Side A) the pattern face are indicated.

Parts face side: Parts on the parts face side seen from

(Side B) the parts face are indicated.

• MAIN board is multi-layer printed board.

However, the patterns of intermediate-layer have not been in-

cluded in the diagram.

*Replacement of IC400 on MAIN board requires a

special tool.

• Lead Layouts

surface

CSP (Chip Size Package)Lead layout of conventional IC

•Waveforms

X400

44.3 ns

2.2 Vp-p

500m V/DIV, 20 ns/DIV

X401

(used USB conector)

62.4 ns

1 V/DIV, 20 ns/DIV

3.4 Vp-p

IC700 8(OSCOUT)

30.6

500 mV/DIV, 20

s/DIV

1.2 Vp-p

NW-E103/E105/E107

•IC Block Diagrams

IC301 NJM2776RB2 (TE2)

– MAIN Board –

V+2

OUT R

STB_TC

IN R

VREF

V+1

X_MUTE

REG

4BIAS

IN L

OUT L

GND

VREF AMP

IC503, IC507 XC9105D091MR

2 1

VREF WITH

SOFT START,

CHIP ENABLE

CURRENT

RIPPLE DETECTION

AND FB

PHASE

COMPENSATION

BUFFER,

DRIVER

RAMP WAVE

GENERATOR,

OSC

GND EXT

VDD

CE VDD FB

VDD

PWM/PFM

CONTROLLER

PWM

COMPARATOR

ERROR

AMP

IC508 XC62HR2802MR IC801 SM8142BD-G-EL

VIN

VSS

VOUT

CURRENT

RESTRICTION

OUTPUT

CONTROL

–

THE SOURCE OF

CONSTANT VOLTAGE

LDR

CHV

OUT1

OUT2

VSS

OSC

ENA

VDD

High voltage

switching circuit

Dividing circuit Dividing circuit

Oscillator for

boosting voltage and EL driver

NW-E103/E105/E107

4-1. BLOCK DIAGRAM

REG USB

IC506

NOR FLASH / SRAM

IC450

NAND FLASH RAM

IC461

USB

CN400

CONNECTOR

VIN VOUT 5

126

38 - 53

185

197 - 207, 2 - 10

187 184 183186 182

15 - 22

29 - 32, 41 - 44 29 - 36, 38 - 45 11

1 - 9, 16 - 25, 48 13 14 1526 28

16 17 18 19 8 9

128

129

130

102

104

173 176

60 57 58 76 74 75 73

8910

133

148

134

127

DATA -

DATA +

GND

VBUS

VDIOUS

UDM

UDP

TRON

VBUS

AN4

AN6/INT8

S701

>/GROUP +

S709

./GROUP –

PF2/EC2/INT4

VDD

LDR

CHV

VDD

VOUT

VDD

EXT

VOUT VIN

VOUT

VIN

IN1

+2.8V

Q460,461

OUT1

IN2

STB

OUT2

VOUT VDD

PI2

OUT2

OUT1

OSCOUT

XRES

XCS1

SLCK

SDA

OSCIN

VDD

ENA1

SCLK

+2.8V

L801

D801

+2.3V

PI5

177

A0 PI6

PC3

SCK0

SO0

PE7

SO1

SI1

SCK1

PC2

PQ2/PGMTR2

106

RST

AOUTR

AOUTL

PI3

VCC

FCE0

FCLE

FAD0 - 7 A1 - 20D0 - 15

FRE

FWP

FWE

FALE

CSI

CS0

CE0

CLE

I/O1 - 8 A1 - 20DQ0 - 15

ALE

BES

RESET

BEF

LBS

UBS

EL PANEL

LIQUID

CRYSTAL

DISPLAY

RTC

IC700

IC801

EL DRIVER

SYSTEM CONTROLLER

IC400

X700

32kHz

137 138

XTAL

EXTAL

X400

22.579MHz

141 142

TEX

X401

16MHz

CORE DET

IC502

+1.2V REG.

IC504

CORE SW

IC501

+2.8V REG.

IC508

+VIO VBUS

+1.2V

+2.8V

+2.3V

+1.2V

+2.8V

IC500

Q503

Q501

Q506,507

J301

HP AMP

IC301

+2.3V REG.

IC509 L501D504

D503

SWITCHING

Q505

SWITCHING REG.

IC507

D501

D502

L500

SWITCHING

Q500

SWITCHING REG.

IC503

I/O DET

IC505

RESET

Q502,504

RESET

Q451,452

S703

VOLUME –

S702

VOLUME +

103

105

AN5

AN7/INT9

+2.3V

DRY

BATTERY

SIZE "AA"

(IEC DESIGNATION LR03)

1PC, 1.5V

S706

PF0/EC0/INT3

S705

REPEAT SOUND

S704

S707

NAND FLASH INTERFACE

USB INTERFACE

A/D, D/A CONVERTER

SERIAL INTERFACE

LEVEL BATTERY DETECT

98AN0

VOUT VDD

RESET DET

IC510

23 24 26 28 27

FRB0 R/B

3029

FCE1 CE1

174

7432

D703

USB

HOLD

87 PG1/DREQ0/INT5

5 1

1 4

5 2

VDD

EXT

6 5

• SIGNAL PATH

: PLAY BACK

: DIGITAL OUT

: DIGITAL IN

1010

NW-E103/E105/E107

4-2. PRINTEDWIRING BOARD – MAIN BOARD (SIDE A) – :Uses unleaded solder.

• Semiconductor

Location

Ref. No.

Location

D300 C-4

D703 C-8

D801 E-3

IC301 D-4

IC461 D-7

IC500 A-6

IC502 F-4

IC505 F-3

IC509 B-5

IC700 E-8

IC801 E-3

Q460 B-7

Q461 A-7

Q501 A-6

Q503 B-6

IC461

IC500

IC509

IC301

IC801

IC505 IC502

IC700

MAIN BOARD (SIDE A)

S701

+ >

S709

.–

EL PANEL

S706

HOLD

S707

1-866-354- (11)

R465

E107

E103/E105

R466

LCD

(LIQUID

CRYSTAL

DISPLAY)

Refer to “

NOTES WHEN REPLACING THE LCD

” (page 22),

when replacing the LCD (liquid crystal display).

Ver. 1.4

Autres manuels pour NW-E103 - Network Walkman

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sony Lecteur MP3

Sony

Sony SEP-30BT - Rolly™ Sound Entertainment... Manuel d'instructions et de sécurité

Sony

Sony Walkman NWZ-B135FRED Manuel utilisateur

Sony

Sony SEP-30BT - Rolly™ Sound Entertainment... Manuel utilisateur

Sony

Sony Walkman NWZ-B152 Manuel utilisateur

Sony

Sony Walkman NWZ-B172 Manuel utilisateur

Sony

Sony Walkman NWZ-B135FBLK Manuel utilisateur

Sony

Sony Walkman NWZ-A815 Manuel utilisateur

Sony

Sony NWZ-E464PNK Manuel utilisateur

Sony

Sony NW-E105 - Network Walkman Manuel utilisateur

Sony

Sony WALKMAN NWZ-E465 Manuel utilisateur

Sony

Sony Walkman NWZ-S715F Manuel utilisateur

Sony

Sony Walkman NW-E8P Manuel utilisateur

Sony

Sony NWZ-E345 - 16gb Walkman Digital Music Player Manuel utilisateur

Sony

Sony Walkman NW-A605 Manuel utilisateur

Sony

Sony NWS706FB Manuel utilisateur

Sony

Sony HAP-S1 Manuel utilisateur

Sony

Sony NWZ-W252 - Digital Music Player 8x Guide de démarrage rapide

Sony

Sony NW-MS9 SonicStage v2.0 Manuel utilisateur

Sony

Sony NWS203FB Manuel utilisateur

Sony

Sony MP3 Walkman Manuel utilisateur

Sony

Sony CSX-V58MP Manuel utilisateur

Sony

Sony CFD-E10 Marketing Manuel utilisateur

Sony

Sony Walkman NW-MS77DR Manuel utilisateur

Sony

Sony Walkman NWZ-S754 Manuel utilisateur

Manuels Lecteur MP3 populaires d'autres marques

Blaupunkt

Blaupunkt Compact Drive MP3 Manuel utilisateur

Memorex

Memorex MMP9008 - 8GB USB 2.0 Manuel utilisateur

Meizu Electronic Technology

Meizu Electronic Technology E5 Manuel utilisateur

Naxa

Naxa NMV-173NX Manuel utilisateur

Philips

Philips PSA250 Manuel utilisateur

Zipy

Zipy go! Waving Manuel utilisateur

Sylvania

Sylvania SMPK4068 Manuel utilisateur

Irradio

Irradio RF-42UC Manuel utilisateur

NABAIJI

NABAIJI SWIM MUSIC 100 Manuel utilisateur

Laser

Laser MP3-A9-4GB Manuel utilisateur

Samsung

Samsung YP-T7F Manuel utilisateur

Savant

Savant SMS-1001-00 Guide de référence rapide

Trevi

Trevi XP 71 BT Manuel utilisateur

AGPtek

AGPtek C2 Manuel utilisateur

MobiBlu

MobiBlu DAH-1500i Manuel utilisateur

Denver

Denver MPS-201 Manuel utilisateur

Steren

Steren MP3-002 Manuel utilisateur

Kenwood

Kenwood M1GD50 Manuel utilisateur