Sony SVR-3000 - Digital Network Recorder Guide de démarrage rapide

WeaKnees.com

http://www.weaknees.com/

TIVO UPGRADE INSTRUCTIONS

Instructions for replace drive upgrade for Sony SVR-3000

A FEW WORDS OF CAUTION:

First and foremost, please be aware that upgrading a TiVo presents a few physical hazards. As

with most consumer electronics devices, components in the TiVo may still carry a lethal charge,

even after disconnecting from your power supply. Be aware of this while working inside your TiVo.

Allow sufficient time for discharging of components and avoid contact as much as possible with

potential hazards. While we have done everything we can to provide accurate, easy-to-follow

instructions, we cannot be responsible for any damage done to your TiVo or to yourself as a result

of your upgrade. By opening your TiVo, you agree that neither Adberg Consulting LLC nor any of its

members or affiliates is responsible in any way for any harm done. Please be VERY careful when

upgrading. NEVER open the TiVo while the unit is plugged in and NEVER operate the TiVo if the lid

is not securely fastened.

Please Note: Opening the TiVo voids the warranty.

1. OPENING THE TIVO

1.1. Unplug the power cord from the TiVo and wait five minutes for the TiVo to

discharge. Do not plug the TiVo back in until you are completely finished. Be very careful

of static electricity, which can destroy your TiVo’s internal parts. You shouldn’t perform

this upgrade on carpet.

1.2. Using a Philips-head screwdriver, unscrew the four screws on the back of

your TiVo. The four screws are surrounded by silver from the top of the TiVo’s.

1.3. Next, remove the four, large-head screws, two on each side of the unit.

1.4. Once the eight screws are removed, you have to remove the lid, which can

sometimes be difficult. The WeaKnees.com “tried and true” method is to place the TiVo on

the floor and kneel down with your knees about 6 inches from the FRONT of the TiVo.

Place your palms on the top side edges of the TiVo, toward the back and push toward the

back of the TiVo (this occasionally requires a bit of force). The cover should slide back and

then up. Remove the cover from the TiVo, and set it in front of the TiVo unit, top up. You

will use this as a platform for the drive bay.

WeaKnees.com

http://www.weaknees.com/

2. DISCONNECTING THE DRIVE BAY

2.1. With the cover off and looking underneath the front lip of the TiVo, you will

be able to see (1) one hard drive, (2) a ribbon cable that runs from the greenish

motherboard underneath the drive to the hard drive, (3) a multi-colored (red, black,

yellow) power cable that runs from the power supply to the hard drive, and (4) a fan cable

that runs from the hard drive bay to the motherboard.

2.2. Place the TiVo lid upright in front of the TiVo, forming a platform that will be

used to support the drive bay after you remove it.

2.3. Gently remove the fan cable from the motherboard. Pull straight up and out.

(See Picture.)

WeaKnees.com

http://www.weaknees.com/

2.4. Using your screwdriver, unscrew and remove the four screws securing the

drive bay to the TiVo chassis.

2.5. Once the screws are removed, you will be able to lift the drive bay up and

out of the TiVo. Flip the drive bay up and out of the TiVo and onto the TiVo lid, with the

hard drive face-down on the TiVo lid and the two cables running from the drive to the

TiVo. You will now need to remove both of the cables connected to the hard drive by

following the instructions below:

(a)The hard drive has a power connector running into the hard drive. The

power cable has a white connector plugged into the hard drive. Remove the power

connector from the hard drive. The power cables are sometimes difficult to remove;

patience and wiggling it back and forth usually does the trick.

(b)Remove the hard drive ribbon cable (longer, gray cable with a blue or

black connector) from the hard drive by pulling on the hard plastic piece connected to the

hard drive.

3. REMOVING THE EXISTING DRIVE(S)

3.1. With the hard drive bay upside down on the TiVo lid, remove the four screws

connecting the hard drive to the hard drive bay. Do not confuse these screws with the

four screws you removed from the back of the TiVo before removing the lid.

3.2. Set aside the drive(s) you have just removed for safe keeping.

4. CONNECTING THE NEW HARD DRIVE TO THE DRIVE BAY

4.1. Included in your upgrade kit is a replacement hard drive. You will need the

four screws that you removed from the hard drive bay. The screws will be used to attach

the upgrade drive to the drive bay.

4.2. Install the drive in the same position as the drive you just removed.

WeaKnees.com

http://www.weaknees.com/

5. CONNECTING THE POWER AND HARD DRIVE CABLES TO THE DRIVE

5.1. If you have the floor/table space, move to the back of your TiVo so that you

are looking at the back of the two hard drives.

5.2. Connect the power cord to the new drive, being sure to align the power

connectors properly (rounded side down). Be sure that the power connector is securely

fastened.

5.3. Connect the hard drive cable to the hard drive. Again, be sure the cable is

pushed snugly into the drive (it only fits one way). Be very careful not to bend any of the

hard drive pins.

5.4. Now move back in front of your TiVo to re-attach the drive bay.

6. RE-ATTACHING THE DRIVE BAY

6.1. Once you have the cables connected to the drive, carefully flip the drive bay

over.

WeaKnees.com

http://www.weaknees.com/

6.2. Align the four screw holes in the bracket with the holes on the TiVo chassis.

Make sure the cables aren’t under the bracket and that the bracket sits flat on the chassis

mount. Make sure the fan cable is free.

6.3. Screw the four screws back into the holes on the drive bay.

6.4. Insert the fan cable back into the motherboard. (This is easy to

forget, which is why it is in bold!)

7. RE-ATTACHING THE TIVO LID

7.1. Kneel down in front of your TiVo as you did when you removed the lid. Place

the TiVo lid back over the TiVo. Align the clips on each side of the lid so that they clip

down on the sides of your TiVo. Slide the lid toward you while simultaneously pushing

down on the top of the lid.

7.2. Once the lid is in place, reattach the eight screws.

We thank you very much for your purchase and hope that you enjoy your newly-enhanced

TiVo. Please email us with any comments, suggestions or complaints. If you found the

upgrade easy to install (or even if you found it more difficult than you expected), we’d

love to know. If you found our service to be excellent (or awful), we want to know that

too. We’re always looking to improve our products and services…the more we hear from

you, the better. Thanks very much!

Autres manuels pour SVR-3000 - Digital Network Recorder

Table des matières

Autres manuels Sony DVR

Sony

Sony BETACAM SX A220P Manuel utilisateur

Sony

Sony HVO-500MD Manuel utilisateur

Sony

Sony DNW-A100 Manuel utilisateur

Sony

Sony HVR-DR60 - 60GB Hard Disk Recorder Manuel utilisateur

Sony

Sony BKMA-U70XGI Manuel utilisateur

Sony

Sony HVRM25AU - Professional Video Cassete... Manuel utilisateur

Sony

Sony Vaio PCG-GRT240G Instructions d'utilisation

Sony

Sony MPEG4 Video Recorder Manuel utilisateur

Sony

Sony SVR-3000 - Digital Network Recorder Instructions et recettes

Sony

Sony SVR-3000 - Digital Network Recorder Manuel utilisateur

Sony

Sony HVO-500MD Manuel utilisateur

Sony

Sony HDR-MV1 Manuel utilisateur

Sony

Sony SVR-3000 - Digital Network Recorder Manuel utilisateur

Sony

Sony Digital Betacam DVW-2000 Manuel utilisateur

Sony

Sony DHG-HDD250 - 30-Hour High-Definition Digital Video... Manuel utilisateur

Sony

Sony PSX DESR-7500 Manuel technique

Sony

Sony SVR-HD700 Manuel utilisateur

Sony

Sony SVR-3000 - Digital Network Recorder Manuel utilisateur

Sony

Sony HVO3000MT Manuel utilisateur

Sony

Sony PDW-F1600 Manuel utilisateur

Sony

Sony VR-510U Manuel utilisateur

Sony

Sony DNW-A100 Manuel utilisateur

Sony

Sony HSR-X200 Manuel utilisateur

Sony

Sony Handycam HDR-CX240 Manuel utilisateur

Manuels DVR populaires d'autres marques

FLIR

FLIR M3100E Series Manuel utilisateur

VTRACKPRO

VTRACKPRO FPRO300 Manuel utilisateur

Swann

Swann NVR-7085 models Manuel utilisateur

XtendLan

XtendLan DVR-1670C Manuel utilisateur

urmet domus

urmet domus 1093/004AHD Manuel utilisateur

Holux

Holux M1 Manuel utilisateur

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuel utilisateur

Whistler

Whistler D16VRS Manuel utilisateur

Defender Security

Defender Security 82-20235 Manuel utilisateur

MISUMI

MISUMI MP-WF100M Manuel utilisateur

Speco

Speco D8HU Manuel utilisateur

UST

UST DDR-E04AA Instructions d'utilisation

Consolidated

Consolidated Digital Video Recorder Manuel utilisateur

Mace

Mace DVR0404RW Guide de démarrage rapide

RCA

RCA RTD315W Manuel utilisateur

FSM

FSM Colibri Grande PRO Manuel utilisateur

Hauppauge

Hauppauge HD PVR 2 Manuel utilisateur

Identivision

Identivision ICR-PH161i PIONEER Manuel utilisateur