Sony PCV-J100 - Vaio Desktop Computer Instructions de montage

Upgrading and Maintaining

Your VAIO Computer

Upgrading and Maintaining Your

VAIO®PCV-J100 Computer

In the future you may want to install additional boards to expand the functionality

of your computer. This section describes how to open your computer and insert

add-in boards, add memory, replace the lithium battery, and install an additional

hard disk drive. For more information on upgrading your Sony computer, see the

computer Reference Manual. You can download the Reference Manual from the

Sony Web site at http://www.sony.com/pcsupport.

Overview

The procedures in this section assume you are familiar with the general

terminology associated with personal computers and withthe safety practices and

regulatory compliance required for using and modifying electronic equipment.

Read “Notes on Use” in the VAIO®User Guide before upgrading your Sony

computer.

!Always switch the power off and remove the power cord from the computer before

you open the system or connect your computer to peripheral equipment;

otherwise, damage may occur to the integrated circuits in your computer.

!Electrostatic discharge (ESD) can damage disk drives, add-in cards, and other

components. Follow the procedures described here only at an ESD workstation. If

such a station is not available, do not work in a carpeted area and do not handle

materials that produce or hold static electricity (cellophane wrappers, for

example). Ground yourself by maintaining continuous contact with an unpainted

metal portion of the chassis while performing the procedure.

Removing the sideplate

To remove the sideplate:

1Remove the screw from the mid-right of the metal sideplate.

2Slide the sideplate backward and out.

Inserting an Add-in Board

Your computer has one open PCI expansion slot, enabling you to install add-in

boards to expand the functionality of your system.

!If you remove the sideplate immediately after you shut down your computer, the

components may be too hot to touch. Wait until the internal parts of the system

unit cool down before you attempt to remove the sideplate.

Removing the PCV-J100 sideplate

✍Some models, such as Configure-to-Order systems, may already contain installed

add-in cards.

!Make sure you observe the proper safety precautions when you add boards to

your Sony computer. See “Notes on Use” in the VAIO User Guide.

VAIO PCV-J100 Upgrading and Maintaining

To insert an add-in board:

1Shut down your computer and turn off all peripheral devices, such as your

printer.

2Unplug your computer and any peripheral devices.

3Remove the sideplate as described on page 3.

4Locate the available expansion slot. Remove the screw, and then remove the

slot cover.

Removing the PCV-J100 slot cover

Adding Memory

5Install the add-in board by plugging it into the expansion slot.

6Attach any internal cables that the board requires (see the manual for the

add-in board).

7Replace the sideplate and reinstall the screws as described on page 16.

8Connect all peripheral devices and AC power, and then turn on the computer.

Adding Memory

The computer has two memory slots. For memory upgrades, use only 3.3V 64-bit

PC-100 SDRAM DIMM modules. Sony computer supplies, accessories, and

peripherals can be purchased from your dealer or by contacting Sony at http://

www.sony.com/accessories.

Installing a PCI board in the PCV-J100

!Make sure you observe the proper safety precautions when you add DIMMs to

your Sony computer. See “Notes on Use” in the VAIO User Guide.

VAIO PCV-J100 Upgrading and Maintaining

To install memory:

1Shut down your computer and turn off all peripheral devices, such as your

printer.

2Unplug your computer and any peripheral devices.

3Remove the sideplate as described on page 3.

4If necessary, remove any cables, add-in cards, or other components to access

the DIMM sockets.

5Handle the DIMM only by the edges, and remove it from its anti-static

package.

6Locate the keys on the bottom edge of the DIMM.

7Align the DIMM over the socket.

8Firmly insert the bottom edge of the DIMM into the socket.

Installing memory in the PCV-J100

!To avoid damaging the DIMM socket, move the DIMM socket tabs slightly

outward to relieve pressure. The DIMM should then click easily into place.

Latch

Edge connectors

Center notch

Notch

Slot

Adding Memory

9Press evenly against the DIMM’s upper corners. The end latches snap into

position automatically.

10 Reinstall any add-in cards or components you removed.

11 Replace the sideplate and reinstall the screws, as described on page 16.

VAIO PCV-J100 Upgrading and Maintaining

Replacing the Lithium Battery

After several years, when the lithium battery starts to weaken, the system settings

stored in CMOS RAM, such as the date and time, may be wrong. When this

occurs, you need to replace the lithium battery.

To replace the lithium battery:

1Write down any changes you have made to the settings in the BIOS Setup

utility. If you have not made any changes to the BIOS settings, proceed to

step 2.

2Shut down your computer and turn off all peripheral devices, such as your

printer. Unplug your computer.

3Remove the sideplate as described on page 3.

4If necessary, remove any cables, add-in cards, or other components to access

the lithium battery.

5Remove the old battery and install the new battery with the plus (+) side up.

Installing a lithium battery in the PCV-J100

Replacing the Lithium Battery

6Replace the sideplate and reinstall the screws, as described on page 16.

!There is danger of the battery exploding if it is replaced incorrectly. You

must replace the battery only with a CR2032-type lithium battery. Discard

used batteries according to the instructions in the VAIO User Guide.

✍The values stored in the CMOS memory are now reset to the factory default

values. You must run the Setup utility to reset the date, time, passwords, and

other changes you may have made to the BIOS settings. If you do not wish to

customize your BIOS settings, you do not need to run the Setup utility. If you

simply wish to reset the date and time, see Windows®Help for instructions.

VAIO PCV-J100 Upgrading and Maintaining

Installing an Additional Hard Disk Drive

Your computer comes with an available internal bay to hold a second standard

3½-inch hard disk drive. (Some models, such as Configure-to-Order systems,

may already have a second hard disk drive.) The hard disk drive access light

blinks when either internal drive is active. For information on how to install

additional drives into the external drive, see the computer Reference Manual. You

can download the Reference Manual from the Sony Web site at http:///

www.sony.com/pcsupport.

1Configure the jumpers on the new drive as a slave (see your drive’s

documentation for configuration instructions).

2Remove the sideplate as described on page 3.

!Before opening the system unit, save any open files, exit Windows, turn off

the power of the computer and all attached peripherals, and then unplug the

power cord.

Installing a hard drive in the PCV-J100

Autres manuels pour PCV-J100 - Vaio Desktop Computer

Table des matières

Autres manuels Sony Ordinateur de bureau

Sony

Sony VGC-LV180J - Vaio All-in-one Desktop... Manuel utilisateur

Sony

Sony VGX-XL301 Manuel utilisateur

Sony

Sony VAIO PCG Series Manuel utilisateur

Sony

Sony VGC-RB50 User Guide (primary user manual) Manuel utilisateur

Sony

Sony PCV-L400 - Vaio Slimtop Computer Manuel utilisateur

Sony

Sony VGC-JS130J/B Manuel utilisateur

Sony

Sony PCV-L630 - Vaio Slimtop Computer Manuel utilisateur

Sony

Sony VAIO VGN-P Series Mode d'emploi

Sony

Sony PCV-RX600N Manuel utilisateur

Sony

Sony PCV-V300G VAIO User Guide (primary manual) Manuel utilisateur

Sony

Sony VGN-NW11S/S Manuel utilisateur

Sony

Sony VGC-LS36N - Vaio All-in-one Desktop Computer Manuel utilisateur

Sony

Sony VAIO VGC-JS100 Manuel utilisateur

Sony

Sony PCV-RX450 Home Networking Solutions Manuel utilisateur

Sony

Sony PCV-L620 - Vaio Slimtop Computer Manuel utilisateur

Sony

Sony PCV-RZ49 VAIO Manuel utilisateur

Sony

Sony VAIO Digital Studio PCV-RS100 Manuel utilisateur

Sony

Sony VPCSA2S9R/BI Manuel utilisateur

Sony

Sony VAIO PCV-RX270DS Manuel utilisateur

Sony

Sony VGC-RB64GY Vaio Manuel utilisateur

Sony

Sony VGN-N300 series Instructions originales

Sony

Sony VAIO VGC-RT100Y Manuel utilisateur

Sony

Sony VGN-FZ21J Manuel utilisateur

Sony

Sony VAIO VAIO Slimtop Computer Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur

HP Z1 Manuel utilisateur

Everex

Everex eXplora Manuel utilisateur

Lenovo

Lenovo ThinkCentre M75e Manuel utilisateur