Sony BDP-S6700 Guide d'installation

The Remote Control Doesn't Work

Check the remote control after each step to see if it is working. If you need model-specific

information to complete any step, check your manual. Manuals are posted on your model support

page.

1. Make sure the device has the latest system software update installed (if applicable).

Downloads are posted on your model support page.

2. Make sure none of the buttons are jammed.

3. Reset the remote control.

1. Remove the batteries from the battery compartment for at least one minute.

2. Press each button on the remote control twice.

3. Use a soft cloth to clean the battery terminals inside the battery compartment.

4. Install new batteries, making sure that they are aligned with the positive (+) and

negative (-) marks inside the battery compartment.

Low or weak batteries can affect the remote control operation.

4. Verify that your remote control sends an infrared (IR) signal.

oFor Android TVs, the front light sensor will blink when the TV receives the IR

signal.

5. Make sure you use the remote control 3 - 10 feet away from the unit, and that you point it

at the remote sensor on the device.

oUsing the remote control too close, too far away, or at various angles may prevent

the IR signal from reaching the device.

oThe IR sensor can be located on the bottom middle, or right side of a TV screen.

oIf your device has an IR mark, the IR sensor is next to it.

6. Remove any objects that may block the IR signal between your remote control and your

device.

oGlass doors or enclosures can affect the signal from the remote. Open glass doors

to see if that makes a difference.

oMove indoor plants and devices that may cause interference.

oMake sure the IR sensor on the device isn't exposed to direct sunlight or bright

lights

Turn off any halogen or fluroscent lights in the room to see if they

are causing interference.

7. Make sure the device you want to control is plugged in and working.

oPress the Power button on the device (not the button on the remote) to turn it on.

8. Perform a power reset on the device that your remote is supposed to control.

oMost devices can be reset when you unplug the power cord for one minute.

oSeparate articles are available to restart an Android TV™ or to power reset other

TVs.

oYou can also check the device manual for specific instructions.

9. Some remote controls can be set for different functions. Make sure that you select the

correct function (TV, BD, DVD, AUX, STB, etc.).

10. Check and adjust the Command Mode setting on your device if your remote control

works with a CD or DVD player, receiver, etc.

oCommand Mode is used when multiple players are used with a single remote.

oOn some players, Command Mode is listed under Options in the Setup menu.

11. Turn off the Light Sensor setting, if applicable.

0. On the TV, not on the remote control, press the HOME button.

1. Using the up or down arrow select Preferences.

2. Press the INPUT button.

3. Press the up or down arrow to select ECO.

4. Press the INPUT button.

5. Use the up or down arrow to select Light Sensor.

6. Press the INPUT button.

7. Press the or down arrow to select OFF.

8. Press the INPUT button.

12. Restore your device to factory default settings.

If the issue still occurs after following the instructions above, you can purchase a new remote

control online. Go to Parts and Accessories.

No picture when I use an HDMI connection

Make sure your TV has the recent system software installed. Downloads are posted on your

model support page.

1. Check which input on the TV the source device is connected to.

2. On the supplied TV remote control, press the INPUT button repeatedly until it displays

the correct HDMI® input where the source device is connected.

3. Disconnect the HDMI cable and then reconnect it. A bad connection may occur

temporarily and cause this issue.

4. If you're using an audio system such as amplifier or theater stand) between the TV and

your video source, make sure that the input setting on the audio system corresponds to the

video output source.

5. Make sure the connected device is set to output through its HDMI connection and the

video format being output is compatible with the TV.

oThe output signal set on your source device may be indicated on its display or in

its menus.

oSome devices may output a 1080/24p or 1080/30p video signal, but some TVs can

only accept a 1080/60p video signal. Changing the video output format of the

connected device may resolve the issue. Check the manual or contact the

manufacturer for further information.

oThe A/V receiver may not up-convert a signal to HDMI if you connected an

analog connection type (Coaxial, Composite A/V, Component A/V, or S-Video)

on the output device and the audio system. Check the receiver manual for details

about other connection options.

6. If the device is connected to an A/V Receiver or other component before being connected

to the TV, try connecting directly to an HDMI input of the TV. If this works, your

receiver or other device may not be an HDMI repeater and might not pass the signal on to

the TV.

oAn HDMI repeater receives an audio/video signal from one HDMI device and

passes it through to another connected HDMI device. While your device is

supported for use with HDMI repeaters, products from other manufacturers may

not be supported.

7. Power reset the TV and the connected device.

8. Try connecting to a different HDMI port on the TV.

oIf the issue is resolved, try connecting back to the previous HDMI port and check

if picture is available.

If picture is still not available, proceed to step 11.

9. Try using a different HDMI cable.

oTo view 1080p (50p/60p) quality picture on the TV from an external device, make

sure to use a High-Speed HDMI cable with the HDMI logo.

10. If possible, try a different device that can output an HDMI video signal using the same

connections.

11. If there's still no picture, perform a factory reset.

oResetting your TV

oResetting an Android TV™

Unable to play a Blu-ray Disc movie.

NOTE: Some Blu-ray Disc® players may display the error Cannot operate this disc or No

Disc Error.

Follow the steps below to troubleshoot if the Blu-ray Disc player cannot read or play a specific

disc.

1. Make sure the disc is playable.

oMake sure the inserted disc is compatible with the Blu-ray Disc player .

oCheck if the region code of the Blu-ray disc or DVD disc matches with the region

code of the Blu-ray Disc player or the DVD player.

NOTE: Check these articles below for additional information on the region codes

for:

Blu-ray disc

DVD disc

oTry playing a different disc, to confirm if the issue is with the disc.

NOTES:

When trying different disc, make sure it has similar specifications as the

first disc you have tried.

If you do not have a different disc, try using the same disc to another

player.

oMake sure you have properly finalized any recordings made on a different player

or recorder.

oFor a 3D Blu-ray Disc movie playback, make sure to use a Hi-speed HDMI®

cable.

2. Make sure the disc is in good working condition.

WARNING: There is a risk of hardware damage. Do not use cleaning discs or

disc/lens cleaners (including wet or spray types). These may cause the apparatus to

malfunction.

oIf the top of the disc tray is dirty, wipe it using a soft dry cloth before placing the

disc on the tray.

oIf there are any fingerprints, stains, or dust on the playing side of the disc, gently

wipe it with a soft dry cloth. Be careful in doing so not to scratch the disc.

oIf the disc is upside down, insert the disc with the playback side facing down.

3. Make sure the settings of the Blu-ray Disc player is correct.

oPower reset the Blu-ray Disc player.

1. Remove the disc from the Blu-ray Disc player.

2. Turn off the Blu-ray Disc player.

3. Unplug the power cord of the Blu-ray Disc player from the electrical

outlet.

4. Let the player remain without power for one minute.

5. Plug the power cord back into the electrical outlet.

6. Turn on the Blu-ray Disc player.

oMake sure that the Parental Control settings are not set to On.

NOTE: Parental control settings can prevent certain discs from being played.

oMake sure that BD ROM 24P Output setting is set to Off.

NOTE: If the BD ROM 24P Output setting is set to On and the TV does not

support this feature, you will see a blank screen on the TV.

oSet the Output Video Resolution setting of the Blu-ray Disc player to the

corresponding setting of the TV.

oWhen playing a Blu-ray Disc that supports BD-Live™ feature, check the

following:

An Internet connection is required. Check the network settings to see if the

Blu-ray Disc player is connected to the Internet.

Set the BD Internet Connection setting in the BD/DVD viewing Settings

menu to Allow.

If you cannot play the disc after setting the BD Internet Connection to

Allow, set the same setting to Do Not Allow, and delete any conflicting

BD-Live data from the BD/DVD Viewing Settings menu. Then, set the

BD Internet Connection setting back to Allow, and try to play the disc

again.

Certain Blu-ray Disc players may require that a USB memory device has

been properly inserted into the EXT slot of the player prior to playing the

movie. If the Blu-ray Disc player being used does not have an EXT input,

skip this step.

NOTE: The USB memory device may need to be re-formatted to FAT32

format or the existing files on the USB device must be deleted prior to

using it with the player. Refer to the support website for details on how to

format the USB to FAT32 file system.

oDownload and install the latest system software. This will ensure that the player is

up-to-date on playback compatibility.

NOTES:

If the player is connected to an active high-speed Internet connection, the

latest system software update can be obtained through the Network

section of the menu.

Autres manuels pour BDP-S6700

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sony Lecteur Blu-ray

Sony

Sony HBD-E385 Manuel utilisateur

Sony

Sony NSZ-GT1 Marketing Manuel utilisateur

Sony

Sony BDP-BX58 Manuel utilisateur

Sony

Sony BDP-S770 - Blu-ray Disc™ Player Manuel utilisateur

Sony

Sony BDP-S5500 Manuel utilisateur

Sony

Sony UHP-H1 Manuel utilisateur

Sony

Sony BDP-S3100 Manuel utilisateur

Sony

Sony BDP-BX38 Manuel utilisateur

Sony

Sony BDP-S500 Manuel utilisateur

Sony

Sony BDP-BX670 Manuel utilisateur

Sony

Sony BDP-S1700ES - Blu-ray Disc™ Player Manuel utilisateur

Sony

Sony BDP-N460 - Blu-Ray Disc Player Manuel utilisateur

Sony

Sony Blu-ray Disc BDP-S485 Manuel utilisateur

Sony

Sony BDP-S3100 Manuel utilisateur

Sony

Sony BDP-S190 Manuel utilisateur

Sony

Sony BDP-BX1 - Blu-ray Disc™ Player Manuel utilisateur

Sony

Sony BDP-S1100 Manuel utilisateur

Sony

Sony BDP-S770 - Blu-ray Disc™ Player Manuel utilisateur

Sony

Sony BDP-S1700 Manuel utilisateur

Sony

Sony BDPS360 - Blu-Ray Disc Player Manuel utilisateur

Sony

Sony BDP-BX2 Manuel utilisateur

Sony

Sony BDP-S780 Manuel utilisateur

Sony

Sony BDP-BX320 Manuel utilisateur

Sony

Sony BDP-S1200 Manuel utilisateur

Manuels Lecteur Blu-ray populaires d'autres marques

Samsung

Samsung BD-F5900 Manuel utilisateur

Philips

Philips BDP3380K Manuel utilisateur

Samsung

Samsung BD-P4600 Manuel utilisateur

Sharp

Sharp BD-HP17U - AQUOS 1080p Blu-ray DiscTM Player Manuel utilisateur

Pioneer

Pioneer BDP-140 Manuel d'installation et d'exploitation

Samsung

Samsung BD-D8200A Manuel utilisateur

LG HLX50W Manuel utilisateur

Marantz

Marantz UD9004 Manuel utilisateur

Panasonic

Panasonic DMR-HCT230 Manuel utilisateur

LG BD611 Manuel utilisateur

Panasonic

Panasonic Diga DMR-PWT420 Manuel utilisateur

LG BD611 Manuel utilisateur

Marantz

Marantz BD7004 Guide de démarrage rapide

Kogan

Kogan KABRP3DWFIA Manuel utilisateur

Toshiba

Toshiba BDX2700 Manuel utilisateur

Samsung

Samsung BD-E5400 Manuel utilisateur

Samsung

Samsung BD-F5100 Manuel utilisateur

Philips

Philips BDP7100 Manuel utilisateur