SonoSite S Series Manuel utilisateur

Serial Bar Code Scanner

Installation Instructions

for S Series Stand

Contents

Bar code scanner

Basket

Overview

Follow these instructions to install the serial bar code scanner on the S Series stand. Installation includes the basket

for storing the bar code scanner.

For information on safety, cleaning, and disinfecting, see Bar Code Scanner User Guide.

WARNING: To avoid the risk of electrical shock or injury, do not connect

more than one peripheral on the S Series stand.

Interface cable

Power supply AC power

cord

Bar code

scanner

Grommets (6)

Adapter

Velcro

strips (2)

Adhesive pad

Hooks (2) Nut plates &

accessory

screws (2)

Basket Allen wrench

Connect AC Power Cord

If a printer or DVD recorder is connected, omit this task. The

AC power cord is already connected.

See also Table 1, “Cables and Connectors” on page 5.

1 Remove the system from the stand. For instructions, see

the S Series Stand User Guide.

2 Insert the AC power cord (J) through the top of the base:

• Insert the end that has prongs.

• Insert into the opening opposite the DC power supply

cord. See Figure 1.

3 Under the base, connect the AC power cord . See Figure 2.

Figure 1 Insert AC power cord (shown

without column attached).

Figure 2 Connect AC power cord.

Attach system to stand

Attach the system to the stand. For instructions, see the

S Series Stand User Guide.

Attach basket

Insert nut plates

1 Insert a nut plate into the groove at the lower back of the

column, and slide it up the column. See Figure 3 and

Figure 4.

The flat, rubber side of the nut plate faces toward the

column.

2 Insert the second nut plate, and slide it up the column.

Figure 3 Insert nut plate.

Position basket

1 Position the two nut plates where desired. Make sure that

their spacing accommodates the two holes on the

basket.

2 Place the basket (the side with two holes) onto the

column.

The two nuts pass through the two holes on the basket.

3 Using the Allen wrench, tighten an accessory screw in

each of the two holes on the basket.

4 Attach hooks to the basket.

The small bend attaches to the basket. The large bend

hangs outward.

Figure 4 Slide nut plate up column.

Attach interface cable

Connect the interface cable to the scanner as instructed

in the DS6707 Quick Start Guide provided.

Figure 5 Attach Interface Cable

Connect adapter and cable to system

1 Connect the adapter (U) to the RS-232 port on the

back of the system. See Table 1, “Cables and Connectors”

on page 5.

The nuts on the adapter face away from the system.

You can place the bar code scanner in the basket as

needed.

2 Connect the interface cable (V) to the adapter, securing

the connector by turning its thumb screws.

Connect and affix power supply

1 Connect the AC power cord (J) to the bar code scanner

power supply (W).

2 Wind up the excess AC power cord, and secure it with a

Velcro strip.

3 Remove the backing from one side of the adhesive pad,

and affix the pad to the power supply, on the side without

the label.

4 Remove the other backing from the adhesive pad, and

affix the power supply vertically to the back of the

column as follows:

• The power supply does not cover the vertical groove

on the column.

• The AC power cord is at the bottom.

Figure 6 Attach power supply to column

Connect power supply to scanner

Connect the bar code scanner power supply cable (W) to

the back of the interface cable connector. See Figure 7.

Figure 7 Connect Power Supply

Secure cables

1 Insert the following cables into the round hook behind

the system:

• Bar code scanner interface cable (V)

• Bar code scanner power supply cable (W)

2 If grommets are in the side of the column, temporarily

remove them.

3 Insert the bar code scanner power supply cable into the

groove along the side of the column, from the top to the

bottom.

4 Insert grommets into the groove, as needed. See Figure 8.

Grommets keep the cable in place.

Figure 8 Insert Grommets

Grommet

Set up system, and program scanner

1 In 2D imaging mode, do one of the following:

• Press Patient, and then press Setup on the horizontal

row of control keys.

• Press Setup on the vertical row of control keys.

2SelectConnectivity.

3IntheSerial Port list, select Bar Code Scanner.

4ClickYes to restart the system.

Restarting activates Bar Code Scanner connectivity.

5 Using the bar code scanner, scan the Carriage Return/

Line Feed bar code.

A copy of the Carriage Return/Line Feed bar code is in

DS6707 Quick Start Guide.

6 Scan additional programming bar codes as desired.

You can program the scanner with various user

preferences, such as beeper volume. Refer to DS6707

Quick Start Guide. For more comprehensive information,

refer to DS6707 Digital Imager Scanner Product Reference

Guide, available on the Mototola Web site at

www.symbol.com/manuals..

Table 1: Cables and Connectors

Letter Name Illustration

Connector 1

[Illustration]

[Connects to]

Connector 2

[Illustration]

[Connects to]

JAC power cord

39 in./1 m

Bar code scanner power supply AC adapter 2

(under stand base)

UBar code scanner

adapter Bar code scanner interface cable RS-232 port

(on back of system)

VBar code scanner

interface cable

Bar code scanner

Bar code scanner adapter and bar

code scanner power supply

WBar code scanner

power supply

Bar code scanner interface cable

AC power cord

S Series, SonoSite, and the SonoSite logo are either trademarks or registered trademarks of SonoSite, Inc.

The SonoSite product(s) referenced in this document may be covered by one or more of the following US patents: 5722412, 5817024, 5893363, 6135961,

6203498, 6364839, 6371918, 6383139, 6416475, 6447451, 6471651, 6569101, 6648826, 6575908, 6604630, 6817982, 6835177, 6962566, 7169108,

D456509, D461895, D509900, D538432, D544962, D558351, D559390, and by the following counterpart foreign patents: AU727381, AU730822,

CA2373065, CN98106133.8, CN98108973.9, DE60021552.0, DE60029777.2, DE60034670.6, DE69730563.5, DE6980539.6, DE69831698.3, FR0875203,

FR0881492, FR0815793, FR1180970, FR1175713, GB0875203, GB0881492, GB0815793, GB1180970, GB1180971, GB1175713, IT0881492, IT0815793,

IT1175713, KR532359, KR528102, NZ542968, RCD000897368-0001, SP0881492, SP0815793. Patents pending.

P09100-02

*P09100-02*

Caution: Federal (United States) law restricts this

device to sale by or on the order of a

physician.

SonoSite, Inc.

21919 30th Drive SE

Bothell, WA 98021 USA

T: 1-888-482-9449 or

1-425-951-1200

F: 1-425-951-1201

SonoSite Ltd

Alexander House

40A Wilbury Way

Hitchin, Herts

SG4 OAP UK

T: +44-1462-444800

F: +44-1462-444801

11/2008

SonoSite, Inc.

Autres manuels pour S Series

Table des matières

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur