611
GETTING STARTED
Battery Placement
Open the battery compartment by sliding the battery
door on the back of the Receiver down and insert the 2
Rechargeable batteries as indicated (+ and – symbols are
molded into the bottom of the battery compartment to
ensure proper placement). Repeat the process for the
Transmitter.
Channel Selection
TheSuperEarLoudandClearprovidesachoiceof
three channels,with theFrequency Selector Switch located
insidethe battery compartment, above thebatteries:
Channel 1 – Far Left Position – 72.2 MHz
Channel2 - Center Position– 72.8MHz
Channel3 –Far RightPosition– 75.8 MHz
The Channel Frequency can be easily changed for
the best possible reception. THE SAME CHANNEL
FREQUENCY MUST BE SELECTED FOR BOTH THE
RECEIVER AND THE TRANSMITTER. IF CHANNEL
FREQUENCIES ARE NOT SYNCHRONIZED,
TRANSMISSION AND RECEPTION WILL FAIL.
Channel frequencies are printed on the inside of the
battery compartment door for quick reference.
Belt Clip Installation/Removal
1) Place belt clip over the Battery Compartment
Door, with the top hinge centered between the two anti-
scuff pads and the clips over the retaining slots.
2) Slip the small joint into the slot located above the
Battery Compartment Door.
3) Apply pressure on both sides of the clip until the
clip retainers snap into the slots on the sides of the unit.
4) To remove, flex out one side of the clip retainer,
unsnap from the retaining slot and remove the clip.
Troubleshooting
If noise, distortion or static is present, check that:
•batteries are high quality and fully charged.
•Transmitter and Receiver are set to the same
Channel.
•there areno otherTransmitters intheimmediate
vicinity transmitting on the same frequency.
•all cables are fully connected.
•theMicrophonehasnotbeendamagedwith
excessive heat or moisture.
•Ear Buds havenot been damaged bypulling on the
wires.
If the above steps do not correct the problem,
contact Sonic Technology Products, Inc. for repair or
replacement.
611
GETTING STARTED
Battery Placement
Open the battery compartment by sliding the battery
door on the back of the Receiver down and insert the 2
Rechargeable batteries as indicated (+ and – symbols are
molded into the bottom of the battery compartment to
ensure proper placement). Repeat the process for the
Transmitter.
Channel Selection
TheSuperEarLoudandClearprovidesachoiceof
three channels,with theFrequency Selector Switch located
insidethe battery compartment, above thebatteries:
Channel 1 – Far Left Position – 72.2 MHz
Channel2 - Center Position– 72.8MHz
Channel3– FarRightPosition–75.8MHz
TheChannelFrequency canbeeasilychangedforthe
best possiblereception. THE SAME CHANNEL FRE-
QUENCY MUST BE SELECTED FOR BOTH THE RE-
CEIVERANDTHETRANSMITTER. IFCHANNEL
FREQUENCIESARENOTSYNCHRONIZED,
TRANSMISSIONANDRECEPTIONWILLFAIL.
Channelfrequenciesareprintedontheinsideofthebattery
compartmentdoorforquickreference.
Belt Clip Installation/Removal
1) Place belt clip over the Battery Compartment
Door, with the top hinge centered between the two anti-
scuff pads and the clips over the retaining slots.
2) Slip the small joint into the slot located above the
Battery Compartment Door.
3) Apply pressure on both sides of the clip until the
clip retainers snap into the slots on the sides of the unit.
4) To remove, flex out one side of the clip retainer,
unsnap from the retaining slot and remove the clip.
Troubleshooting
If noise, distortion or static is present, check that:
•batteries are high quality and fully charged.
•Transmitter and Receiver are set to the same
Channel.
•there areno otherTransmitters intheimmediate
vicinity transmitting on the same frequency.
•all cables are fully connected.
•theMicrophonehasnotbeendamagedwith
excessive heat or moisture.
•Ear Buds havenot been damaged bypulling on the
wires.
If the above steps do not correct the problem,
contact Sonic Technology Products, Inc. for repair or
replacement.
