SOLIS 4G series Manuel utilisateur

User Manual

for 4G Series Grid Inverter - Solis-1P(6-10)K-4G-US

Version 1.0, Release Date: 12,2022

Applicable Models

Solis-1P6K-4G-US

Solis-1P7.6K-4G-US

Solis-1P10K-4G-US

Applicable System

Single phase Grid-Tie system

● Product specifications are subject to change without notice. Every attempt has been made to

make this document complete, accurate and up-to-date. Individuals reviewing this document and

installers or service personnel are cautioned, however, that Solis reserves the right to make changes

without notice and shall not be responsible for any damages, including indirect, incidental or

consequential damages caused by reliance on the material presented including, but not limited to,

omissions, typographical errors, arithmetical errors or listing errors in the material provided in this

document.

● Solis accepts no liability for customers' failure to comply with the instructions for correct

installation and will not be held responsible for upstream or downstream systems Solis

equipment has supplied.

● The customer is fully liable for any modifications made to the system; therefore, any hardware or

software modification, manipulation, or alteration not expressly approved by the manufacturer

shall result in the immediate cancellation of the warranty.

● Given the countless possible system configurations and installation environments, it is essential to

verify adherence to the following:

● There is sufficient space suitable for housing the equipment.

● Airborne noise produced depending on the environment.

● Potential flammability hazards.

● Solis will not be held liable for defects or malfunctions arising from:

● Improper use of the equipment.

● Deterioration resulting from transportation or particular environmental conditions.

● Performing maintenance incorrectly or not at all.

● Tampering or unsafe repairs.

● Use or installation by unqualified persons.

● This product contains lethal voltages and should be installed by qualified electrical or service

personnel having experience with lethal voltages.

Important Notes

Table of Contents

10 Appendix

9 Specifications

8 Troubleshooting

7 Maintenance

6 Operation

5 Start and Stop

4 Installation

3 Overview

2 Safety Instructions

1 Introduction

Contents

1. Introduction

2. Safety Instructions

2.1 Safety Symbols

2.2 General Safety Instructions

2.3 Notice For Use

3. Overview

3.1 Front Panel Display

3.2 LED Status Indicator Lights

3.3 Keypad

3.4 LCD

4. Installation

4.1 Select Location for the Inverter

4.2 Mounting the Inverter

4.3 Electrical Connections

…………………………

………………………………………

…………………………………………………

…………………………………

…………………………

………………………………………………

…………………………………………………

………………………………………………

………………………

………………………………

5. Start & Stop

5.1 Start-up procedure

5.2 Shutdown procedure

………………………………………………

…………………………………

………………………………

………………………………………………

……………………………………

1.1 Product Description 1

…………………………………

1.2 Inverter Knockouts 3

…………………………………

1.3 Wiring Box Interior View 3

……………………………

3.5 Wiring Circuit Diagram 9

……………………………

1.4 Packaging 4

……………………………………………

1.5 Tools Required for Installation 4

………………………

1.6 Storage 5

………………………………………………

2.4 Notice For Disposal 7

…………………………………

Contents

6. Operation 24

………………………………………………

…………………………………………

6.1 Main Menu

………………………………………

6.2 Information

6.3 Settings

6.4 Advanced Info.

……………………………………………

………………………………………

6.5 Advanced Settings 30

……………………………………

7. Maintenance

8. Troubleshooting

9. Specifications

……………………………………………

…………………………………………

……………………………………………

6.6 ARC Fault ……………………………………………

1. Introduction User Manual

Wiring box

LCD display

4 buttons

LED lights

Figure1.1 Front view of inverter and and Wiring box (The wiring box components

1.1 Product Description

Solis single phase US series inverters can invert the DC power from (PV) solar modules

into AC power which can support home loads and feed back to the grid.

This product manual is valid for the below listed Solis 1φ inverters

1- Solis-1P6K-4G-US

2- Solis-1P7.6K-4G-US

3- Solis-1P10K-4G-US

vary based on the MLRSD transmitter choice)

1.1.1 Front View of the inverter

DC Switch Meter

DC input

AC input

RS 485

COM

1. Introduction User Manual

1.1.2 Bottom and Side View

Figure1.2 Bottom view

Figure1.3 Side view (Right) and back view (left) of the inverter

1.3 Wiring Box Interior View

1. Introduction User Manual

Table 1.1 Knockout quantity and size

The inverter comes equipped with the following knockouts at the bottom, back and

the side of the wiring box, Adding additional knockouts shall void the inverter warranty

1.2 Inverter Knockouts

Location Quantity Size of Conduit Purpose

Bottom 3

1 x 1"

1 x 1/4"

Knockout for DC input cable

Knockout for AC output cable

Knockout for communication cable

Back 2 1 x 3/4"

1 x 3/4"

knockout for DC input cable

knockout for AC output cable

Right Side 1 1 x 3/4" knockout for AC output cable

Left Side 1 1 x 3/4" knockout for DC input cable

Grounding

Terminal Tigo Transmier

DC Wiring

Terminal

AC Wiring

Terminal

Internal DC Wiring

Internal AC Wiring

Internal Meter

Wiring

Tigo Core (PLC Signal Inducer)

Internal COM Wiring

Figure1.4 Inside the Wiring Box (RSD Transmitter device can vary)

1.4 Packaging

When you receive the inverter, ensure a thorough inspection for any visible damage to

the packing case or the products and ensure that all the parts listed below are included:

1. Introduction User Manual

Manual

Inverter x1

Expansion screws x3

Locking screws x1 Manual x1

Mounting bracket x1

1.5 Tools Required for Installation

Technician Screwdriver Phillips Screwdriver Wire Strippers 12AWG to 6AWG Wire Strippers 20AWG to 10AWG

Drill and Impact Driver

Mulmeter (AC/DC amps)

Channel Locks

Smart Phone

Torque Wrench Screwdriver

In case of any damage and missing component, contact Solis US Service team at

ussales@solisinverters.com

1. Introduction User Manual

1.6 Storage

● Use the original packing box with the desiccant inside to pack the inverter.

Store the inverter in a clean and dry place, free of dust and dirt. The storage temperature ●

must be between -13~176 F and humidity should be between 0 to 95%, non-condensing.°

Do not stack more than four (4) inverters high on a single pallet. ●

Keep the box(es) away from corrosive materials to avoid damage to the inverter enclosure.●

Inspect the packaging regularly. If packing is damaged (wet, pest damages, etc.), repackage●

the inverter immediately.

Store inverters on a flat, hard surface -- not inclined or upside down.●

After 100 days of storage, the inverter and carton must be inspected for physical damage ●

before installing. If stored for more than 1 year, the inverter needs to be fully examined

and tested by qualified service or electrical personnel before using.

Restarting after a long period of non-use requires the equipment be inspected and, in ●

some cases, the removal of oxidation and dust that has settled inside the equipment will

be required.

Improper use may result in potential electric shock hazards or burns. This manual contains ●

important instructions that should be followed during installation and maintenance.

SAVE THESE INSTRUCTIONS – This manual contains important instructions for the following

models that shall be followed during installation and maintenance of the inverter

Solis-1P6K-4G-US

Solis-1P7.6K-4G-US

Solis-1P10K-4G-US.

If the inverter is not installed immediately, the following storage instructions and environmental

conditions must be followed

Autres manuels pour 4G series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SOLIS Onduleur

SOLIS

SOLIS Single Phase Inverter Manuel utilisateur

SOLIS

SOLIS Solis-125K-EHV-5G Manuel utilisateur

SOLIS

SOLIS S6-EH3P5K2-H Manuel utilisateur

SOLIS

SOLIS S5-GC75K Manuel utilisateur

SOLIS

SOLIS 4G Mini Manuel utilisateur

SOLIS

SOLIS S6-EH1P3.8K-H-US Manuel utilisateur

SOLIS

SOLIS S6-EH1P3.8K-H-US Manuel utilisateur

SOLIS

SOLIS S6-EA1P3K-L-S Manuel utilisateur

SOLIS

SOLIS S6 Series Manuel utilisateur

SOLIS

SOLIS 100K-5G-AU Manuel utilisateur

SOLIS

SOLIS RHI Series Manuel utilisateur

SOLIS

SOLIS 4G series Manuel utilisateur

SOLIS

SOLIS Solis-3P12K-4G Manuel utilisateur

SOLIS

SOLIS TURBO ENERGY Lithium Series Manuel utilisateur

SOLIS

SOLIS S5-GC75K-US Manuel utilisateur

SOLIS

SOLIS 1P6K-4G-US Manuel utilisateur

SOLIS

SOLIS Solis-100K-5G Manuel utilisateur

SOLIS

SOLIS S6 Series Manuel utilisateur

SOLIS

SOLIS S6 Series Manuel utilisateur

SOLIS

SOLIS S5-EH1P3K-L Manuel utilisateur

SOLIS

SOLIS S6-EH1P3.8K-H-US Manuel utilisateur

SOLIS

SOLIS RHI-HV 5G Series Manuel utilisateur

SOLIS

SOLIS 75K-5G-PRO Manuel utilisateur

SOLIS

SOLIS Solis-1P1K-4G Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur