Solight 1D37 Manuel utilisateur
EN Solight 1D37 Flammable Gas Detector
Dear Valued Customer, allow us to thank you for purchasing our product. Read and
follow the following instructions carefully. Doing so will avoid improper use or damage to the product.
Carefully keep the present operating manual. Intended for indoor use. Never expose to environments with
high humidity (such as bathroom), avoid contact with fluids.
Introduction
This device is designed to detect flammable gases that may leak from mains or general household
appliances. However, it cannot detect the toxic carbon monoxide (CO) or smoke. The detector is capable of
detecting liquefied petroleum gas, natural gas, coal gas, methane, propane and butane.
butane
heavier than air
methane
lighter than air
propane
heavier than air
coal gas
lighter than air
natural gas
lighter than air
liquefied petroleum gas
heavier than air
Installation
As shown in the table above, some gases are lighter than air and others are heavier. Therefore, it is
important to realize what gas may start to leak and to choose the proper location accordingly. Do not place
the device to locations exposed to draughts, close to ventilation devices or other areas that may logically
affect proper operation.
Gas lighter than air: Place the detector 0.3 to 1m
from the ceiling within 3m of the gas appliance.
Gas heavier than air: Place the detector 0.3 to 1m
from the floor within 3m of the gas appliance.
Insert a rechargeable 9V battery into the battery
compartment. Now place the detector to the
selected location and plug it into a 220-240V, 50Hz
power socket. The green LED will go on and the
light LED will start flashing. After approx. three
minutes the device is ready to detect flammable
gases.
Alarm
The device will trigger an audible audible and visual (red flashing LED) signal upon detection of an identifiable
gas at a concentration exceeding 2500PPM. In this case, close the gas supply and ventilate the room. In case
of occurring false alarms, check the correct location of the device.
Maintenance
Wipe the device with a dry or slightly damp cloth at monthly intervals. Do not use detergents or inject
anything into the device. Have the device checked by a service centre or a specialist half-yearly.
Parameters
Sensor sensitivity
2500PPM (±1500PPM)
Sensor service life
3 years
Backup battery life
2 hours standby mode / 30 minutes alarm
Audible signal
85dB / 0.3m
Dust and water ingress protection
IP30
Cable length
135cm
Operating temperature / humidity
0 –50°C / 10 – 95%
This flammable gas detector has a certificate confirming its compliance with the requirements of the Czech
technical standard ČSN-EN 50194-1:2009, Electrical apparatus for the detection of combustible gases in
domestic premises. Compliance with this standard has been confirmed by the independent research
laboratory ISET (Testing Certification Technology).
Certificate number: IT111935JB160325S; Test Report No.: POCE16072203BRS
Importer: Solight Holding, s.r.o., Na Brně 1982, Hradec Králové 500 06, Czech Republic
Manufacturer:
SHENZHEN JIKAIDA TECHNOLOGY CO., LTD
A301, Buiding 31, Taixing lndustrial Park, Hongxing
community, Songgang Street, Bao'an District,
Shenzhen City, Guangdong Province, China
Table des matières
Autres manuels Solight Détecteur de gaz
Manuels Détecteur de gaz populaires d'autres marques
Macurco
Macurco GD-6 Manuel utilisateur
Evikon
Evikon E2632 Manuel utilisateur
Critical Environment Technologies
Critical Environment Technologies CGAS-A Series Manuel utilisateur
MSA
MSA altair 5 Manuel utilisateur
DOD Technologies
DOD Technologies ChemLogic CL96 Manuel utilisateur
DEGA
DEGA NS III LCD Series Manuel utilisateur
